ABB

Digital Output Module

Channels: 20 single-ended channels 
Voltage: ±10 V DC
Current: 0–20 mA, 4–20 mA
Voltage Inputs: >1 MΩ.
Current Inputs: 250 Ω 
Noise Rejection: >80 dB (50/60 Hz)
Channel-to-Backplane: 1,500 V AC RMS

COMMUNICATION UNIT

Data Throughput: Up to 10,000
RAM: 512 KB
Voltage: +5V DC
Consumption: 10 W (typical)
Isolation:1500V AC 
Fiber optic: Up to 4 km
Max Nodes: Up to 250 devices per loop

Control unit

Processor:32-bit 
I/O Capacity Up to 1,024 I/O points
Voltage: +5V DC
Consumption: 15 W
Battery Backup:BCL003 battery module

Modbus TCP Interface Module

CI867AK01
Advant 800xA Modbus 
TCP Interface Communication Module 

Multi Fuel-flame Detector

Detection Range:Up to 40 meters 
Response Time:< 3 seconds 
Supply Voltage:24 V DC
Power Consumption:4–8 W (DC)
Relay Contacts: 2× SPDT 
Analog Output: 4–20 mA

SPEED MEASURING BOARD

Speed Range:0–12,000 RP
Accuracy:±0.1% of full scale (25°C)
Resolution:1 RPM 
Supply Voltage:+24 V DC (±10%) 
Power Consumption:≤5 W
Input Sensitivity:50 mV–30 V RMS (MPU)
Isolation :1500 V AC (channel-to-logic)

POWER INTERFACE BOARD

Input Voltage:24 V DC
Logic Voltage:+5 V DC (±5%), Max 8 A
Analog Voltage:±15 V DC (±5%), Max 1 A
Isolation 1500 V AC
2× Isolated Outputs
Power Redundancy:Supports dual power supplies

Inverter Board

DC Link Voltage:200–480 V DC 
Output Phase Voltage:0–480 V AC
Max Output Current:Up to 45 A 
Switching Frequency:4–16 kHz 
IGBT Technology:Trench-gate IGBTs

Safety Board

CPU Module

Model:PM590-ETH
Order Code:1SAP150000R0270
Type:Compact PLC Processor with Integrated Ethernet
Series:AC500-eCo 
Power Supply:24 V DC (±20%)
Consumption: 6 W (typical)
CPU:32-bit RISC Processor
Isolation :1500 V AC

IGBT MODULE + BOARD

NSULATED GATE BIPOLAR TRANSISTOR
500A I(C)
1200V V(BR)CES
N-CHANNEL
IGBT MODULE + BOARD
FOR INVERTER DRIVE

CEX-Bus Interconnection Unit

Bus Protocol:CEX-Bus
Data Rate:10 Mbps 
Fiber Type:62.5/125 μm multimode
Redundancy:Dual-path redundancy 
Node Capacity:Up to 32 nodes 
Power Supply:24 V DC (±10%)
Power Consumption;≤ 5 W
Isolation:2500 V AC

Softstarter

Type:Thyristor-Based Soft Starter
Rated Current:142 A 
Motor Power (400V):75 kW 
Input: 208–690V AC (±10%), 50/60 Hz
Control Circuit: 100–250V AC/DC
Current Limit: Adjustable (200–500% I_e)
Pump Stop: Anti-water-hammer control

Control Card

Power Supply:24V DC
Voltage: 15–30V DC
Current: 3–8 mA
Rating: 2A @ 250V AC
Resolution: 10-bit
Load Impedance: ≥500Ω (voltage)
Baud Rate: 9600–115200 bps
Isolation:1500V AC

SPEED UP UNIT

Input Voltage:24 V DC
Power Consumption:≤ 8 W
Torque Response: ≤ 2 ms
Accel/Decel Rates: Up to 3x faster vs
Overload Capability: 200%
Type:Dynamic Performance Module 

Analog Input Board

Power Supply:24V DC (±10%) 
Power Consumption:≤ 4 W
Voltage: 0–10V
Current: 0–20mA
Resistance: Pt100/Pt1000 RTDC
Resolution:16-bit 
Sampling Rate：10 ms/channel
Voltage: ≥1 MΩ
Current: 250Ω ±0.1%
Channel-to-Channel: 300V AC
Channel-to-Backplane: 1500V AC

ANALOG INPUT BOARD

Power Supply:24V DC (±10%) 
Power Consumption:≤ 3 W
Input Channels:8x Isolated Voltage Inputs 
Resolution:16-bit 
Accuracy:±0.1% of FS (Full Scale) at 25°C
Input Impedance ≥1 MΩ
Sampling Rate:10 ms/channel
Channel-to-Channel: 300V AC
Overvoltage Protection:±30V continuous

Analog Input Module

Overload Protection:±30V (voltage)
Power Supply:24V DC 
Power Consumption:≤ 1.5 W
Input Channels:4x Isolated Channels
Voltage: 0–10V, ±10V, 0–5V
Current: 0–20mA, 4–20mA
Resolution:12-bit 
Sampling Rate:2 ms per channel
Voltage: ≥100 kΩ
Isolation:1500V AC 

DIGITAL INPUT CIRCUIT BOARD

Type:8-Channel Isolated 
Sink/Source: Auto-detecting
Voltage Range: 15–30V DC
Input Current 3–8 mA
Response Time:≤ 2 ms
Isolation:1500V AC 
Power Supply:24V DC
Power Consumption:≤ 1.8 W

Digital Output Module

Output Signal: 24V DC
Load Current per Channel:0.5A to 2A
Max Switching Voltage: 30V DC
Isolation Voltage: 500V AC/DC
Response Time: <1ms 

CURRENT FEEDBACK BOARD

Supply Voltage:24V DC 
Current Input :3-phase AC
Isolation Voltage:2500V AC
Frequency Range:0–500 Hz

Industrial Circuit Board

Power Supply:24V DC
Analog Inputs: 4-20mA
Digital I/O: Opto-isolated inputs
Communication: Possible RS-485/Modbus 
Type: Industrial control

IGITAL OUTPUT MODULE

DRIVE BOARD
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-FK
Number of Channels: Typically 4 or 8 
Switching Capacity: Up to 2A per channel 
Supply Voltage: 24V DC 
Isolation Voltage: 1500V AC
Response Time: <1ms

Digital I/O card

Input Voltage:24V DC nominal (15-30V range)
Input Current :3-5mA per point 
Output Type:Relay (Form C) or Solid State 
Output Rating:2A @ 30V DC
Isolation Voltage:1500V AC 
Response Time:<1ms (input)

INTERCONNECTOR

Contact Configuration:96-position (48x2 rows)
Contact Material:Gold-plated copper alloy
Current Rating:1A per contact (max)
Voltage Rating:60V DC max
Contact Resistance:<20mΩ (initial)
Insulation Resistance:>100MΩ @500V DC
Mating Cycles: >500 insertions