ABB

AC 800M Controllers

ISA Secure certified - Read more
Reliability and simple fault diagnosis procedures
Modularity, allowing for step-by-step expansion
IP20 Class protection without the requirement for enclosures
The controller can be configured with 800xA control builder
The controller has full EMC certification
Sectioned CEX-Bus using a pair of BC810 / BC820
Hardware based on standards for optimum communication connectivity
(Ethernet, PROFIBUS DP, etc.)
Built-in redundant Ethernet Communication ports

AC 800M Controllers

ISA Secure certified - Read more
AC 800M High up to SIL 3 certified using PM857/SM812,PM863/SM812
PM865/SM811 or PM867/SM812
Supports S800 I/O High Integrity 
(PM857, PM863, PM865, PM866A and PM891)
The controller can be configured with 800xA control builder
The controller has full EMC certification
TÜV Certified SIL 2 and SIL 3
Built-in redundant Ethernet Communication ports

Safety CPU module

Use with PM857, PM863 and PM867
Package including
SM812, Safety Module
TP868, Baseplate
TK852V10, Syncronization link cable

Digital input submodule

Rated Voltage:24 V DC (18 … 30 V)
Input Current:4 mA @ 24 V  
Thresholds:ON ≥ 15 V, OFF ≤ 5 V, 2 V hysteresis
Minimum Pulse:200 µs 
Isolation:500 V AC channel-to-back-plan 

FEEDER PROTECTION AND CONTROL

Three-phase non-directional overcurrent protection
Double earth-fault protection 
Non-directional earth-fault
Non-directional sensitive earth-fault
Directional earth-fault protection
Transient/intermittent earth-fault protection
Negative-phase-sequence protection
Phase discontinuity
Three-phase transformer inrush detector
Three-phase thermal overload, lines and cables
Circuit breaker failure protection
Electrically latched lockout relay

Power Supply

NSD570
1KHW002144R0001
Additional items NSD570
G3LK, Power Supply 110-250 VDC/VAC NSD570

Feeder Terminal

FEEDER TERMINAL
BASE UNIT
HUMAN INTERFACE

MACH 3 Distributed I/O unit

Input Voltage:24V DC (19.2-30V)
Power Consumption:12W (typical), 18W (max)
Backplane Current:800mA (max)
Isolation :1500V AC 
Digital Channels:32
Analog Channels:8 (16-bit resolution)
Protocols Supported:PROFINET IO, Modbus TCP
Data Rate:100Mbps (full duplex)
Cycle Time:≤1ms (synchronized)
Jitter:<1μs

Analog Signal Multiplier

Power Supply:24V DC (±10%)
Power Consumption:3.5W
Input Signals:2× (0-10V or 4-20mA)
Output Signal:0-10V or 4-20mA 
Input Impedance:1MΩ (voltage), 250Ω (current)
Isolation:1500V AC 
    

Splitter Board

Input Voltage:24V DC (±10%)
Power Consumption:2W max
Isolation Voltage:1500V AC
Input Channels:4 (configurable)
Output Channels:8 (1:2 splitting ratio)
Signal Types:4-20mA, 0-10V, digital

Exciter Control Module

Power Supply:110/220V AC ±10% or 24/48V DC
Power Consumption:50W (max)
Field Voltage :0-300V DC (adjustable)
Field Current:0-20A DC (continuous)
Control Accuracy:±0.25% of setpoint
Response Time:<10ms
Voltage Regulation:±0.5% of nominal
Frequency Range:40-70 Hz
Stability:<0.1% oscillation
Harmonic Distortion:<1% THD

Processor Unit Relay Card

Operating Voltage: 24V DC
Power Consumption: ≤5W
Isolation: 2.5kV AC 
Processor: 32-bit DSP
Memory:64MB Flash

Analog I/O Module

ANALOG I/O
MODULE 8AI
24 VDC
U/I/RTD
8/12BIT+SIGN 1/3-WIRE
CS31

OEI-BOARD

Power Supply:24V DC (-15%/+20%)
Power Consumption:6W typical
Optical Interfaces:2× 100BASE-FX (1300nm)
Electrical Interface:1× 10/100BASE-TX
Isolation:1500V AC
Data Rate:100Mbps full-duplex

AC centrifugal fan

FAN
CENTRIFUGAL
230 VAC
290WATT
50 HZ
0,88 A
2050 RPM
DRIVE MOUNT

Communication Gateway

MLink Hardware Version 2
Internal: Modbus TCP
Fieldbus: Profibus
Modbus RTU/TCP, PROFINET IO

CONTROL BOARD

Input Voltage:24V DC (±10%) 
Power Consumption:≤50W (max)
Relay Outputs:2x SPDT (5A @ 230V AC)
Digital Inputs:2x (24V DC)

Combined overcurrentand earth-fault relay

Protection Functions:3-Phase Overcurrent (OC) 
Rated Frequency:50/60 Hz
Rated Current (Iₙ):1 A or 5 A
Auxiliary Supply:24/48/110/125 V DC
Rated current:1 A
continuously:4 A
Input impedance:<100 mΩ

ANALOG INPUT MODULE

ANALOG INPUT MODULE
32 CHANNEL
P72122-4-0788722
Current: 4–20 mA, 0–20 mA
Voltage: 0–10 V, ±10 V, 1–5 V
Resolution: 16-bit 
Accuracy: ±0.1% of full scale

Charging Control Board

Input Voltage Range: 380-480V AC (3-phase)
Output Voltage: 12-600V DC 
Charging Current: 10-100A
Efficiency: >92%
Frequency: 50/60Hz ±5%
Voltage Accuracy: ±0.5% of full scale
Current Accuracy: ±1% of full scale

IGBT MODULE

Voltage Ratings: 1200 V
Nominal Collector Current: 300 A
IGBT: 0.08 K/W
Diode: 0.10 K/W
Gate-Emitter Threshold Voltage : 6 V

TZIDC ELECTRO-PNEUMATIC POSITIONER

Power Supply: 10.5–30V DC 
Analog: 4–20mA 
Digital: PROFIBUS DP/PA
Position Feedback: 4–20mA
Control Accuracy: ±0.5% of span
Supply Pressure: 1.4–7 bar (20–100 psi)
Output Pressure: 0–100% of supply pressure
Air Consumption: < 0.12 Nm³/h
Response Time: < 1 sec

IGCT Module

Nominal On-State Current (ITAV):2000A*
Maximum Surge Current (ITSM):20kA (1ms)
Critical di/dt:500A/μs
Maximum Blocking Voltage (VDRM):1700V
Repetitive Peak Reverse Voltage (VRRM):1700V
Gate Trigger Voltage (VGT):1.5-2.5V
Recommended Switching Frequency:≤500Hz

IGCT Module

Nominal On-State Current (ITAV):2500A
Peak Surge Current (ITSM):25kA (1ms)
Critical di/dt:800A/μs
Maximum Blocking Voltage (VDRM):4500V
Repetitive Peak Reverse Voltage (VRRM):4500V
Gate Trigger Voltage (VGT):1.5-2.5V

IGCT Module

Repetitive Blocking Voltage:4500V
Non-Repetitive Blocking Voltage (VDSM):4500V
Gate Trigger Voltage (VGT):1.5-2.5V
Average On-State Current (ITAV):3500A
Peak Surge Current (ITSM):30kA (1ms)
Critical di/dt:1000A/μs
Peak Gate Current (IG):50A
Gate Power Dissipation:20W