PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
- We prepare clear, order-specific documentation for every international shipment, including the commercial invoice, packing list and available product or compliance documents. Before dispatch, our logistics team confirms the consignee details, declared value, shipping terms and destination requirements with you. Tracking information is provided after shipment, helping your team prepare for import clearance with confidence.
Documents checked before dispatch · Shipment details confirmed · Global tracking provided
- Payment
- Payment is by bank wire only in RMB/CNY, GBP, EUR or USD. Amikon does not accept credit cards or provide credit terms. Cleared payment is required before shipment unless the written quotation expressly states otherwise.
- Product Condition
- Factory New These are new and current items that are procured directly from the manufacturer.
New In Sealed Package Parts are new. They have not been used and still have their original package seal intact.
New in Original Package These parts are new. The packages were not originally sealed by their original manufacturer.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
AO561 sends engineered analog commands to field devices
ABB AO561 generates two configurable analog output signals for an AC500 S500-eCo station. Each channel can serve a voltage or current load through its assigned terminals; the unused signal terminal of that channel must remain disconnected.
Order 1TNE968902R1201 for AO561. Match the receiver burden, signal reference and selected range before energizing the output. The output circuits are not galvanically isolated, and hardware index E0 changes resolution and electrical consumption relative to earlier versions.
Order 1TNE968902R1201 for AO561. Match the receiver burden, signal reference and selected range before energizing the output. The output circuits are not galvanically isolated, and hardware index E0 changes resolution and electrical consumption relative to earlier versions.
BEFORE YOU BUY
Check the receiving circuit before ordering
ACTUAL APPLICATIONS
Where AO561 delivers analog control references
ABB documents drive-reference and analog-actuator connections. The receiver circuit, selected signal mode and load limits determine whether the installation is suitable.
-
01 · DRIVE REFERENCE
Provide a differential drive input signal
The MicroFlex e190 manual includes an AO561 connection to its analog input. Use the documented signal and return terminals, follow the drive-specific shield instruction and verify the programmed analog-input function before enabling motion. -
02 · CURRENT ACTUATION
Command a current-input actuator
Use the configured current-output terminal for a compatible analog actuator. Include receiver and wiring resistance in the 0 to 500 ohm load check, and leave the corresponding voltage-output terminal disconnected. -
03 · VOLTAGE ACTUATION
Set a voltage-input receiver reference
Connect the selected voltage output to a compatible receiver and common signal return. Keep the load within the maximum plus or minus 2 mA capability and make the installation safe during low-supply or power-transition conditions.
Technical specifications for AO561
-
Product ModelAO561
-
Product ParametersTwo-channel Analog Output Module
-
In stock1 unit
-
ManufacturerABB
-
Analog output channels2 configurable voltage or current outputs
-
Signal polarityBipolar voltage; unipolar current
-
Output resolution12 bits incl. sign; 13 bits incl. sign at E0 or later
-
Current-output load0 to 500 ohm
-
Voltage-output load currentMaximum +/-2 mA
-
Process supply rating24 V DC; -15% to +20%
-
Process supply consumption100 mA plus load; 10 mA plus load at E0 or later
-
Maximum module dissipation3.1 W; 1 W at E0 or later
-
Galvanic isolationNo
-
Output data length4 bytes
-
Conversion errorTypical +/-0.5% FS at +25 deg C; max. +/-2% FS at 0 to +60 deg C or EMC disturbance
-
Supply ripple limitMaximum 5%
-
Voltage-output terminalsChannel 0: 13; channel 1: 15
-
Current-output terminalsChannel 0: 14; channel 1: 16
-
Shielded signal cableUp to 100 m; conductor cross-section greater than 0.14 mm2
View all additional
Alternative Names
AO561
1TNE968902R1201
S500-eCo voltage/current output
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
S500-eCo ANALOG COMMANDS
Match output mode, reference and receiver burden
AO561 supplies two configured voltage or current commands through different terminal pairs. The two channels share the documented reference arrangement and do not provide galvanic isolation.
Voltage signals use terminals 13 and 15; current signals use 14 and 16. The shared output return is terminal 17, with 24 V DC process supply on 19 and 20. Never connect both signal alternatives of one channel simultaneously.
Confirm the removable terminal block, receiver burden and safe output behavior during supply changes. Restore the engineered channel configuration and use the actual hardware index when checking resolution and power ratings.
Features:
- Select voltage or current deliberately
- Check load and reference potential
- Verify safe receiver behavior at power transitions
The ABB AO561 requires the selected output circuit, receiver loading and common reference to be checked before system integration and commissioning.
INTERCHANGEABILITY
Verify the complete replacement identity before commissioning
The ABB AO561 data sheet revision 12, dated 2024-11-15, lists this order as Active. Replacement assessment still depends on the installed hardware index and receiving circuit, not simply the presence of two analog channels.
Record each channel mode, scaling, receiver load and terminal assignment before exchange. A lower-power later index does not remove the need to inspect output behavior and validate the actual connected equipment.
Isolate all supply and process voltages before removing the module or terminal block. After replacement, compare controller commands with measured output and receiver response while keeping actuators in a safe test state.
Features:
- Preserve channel mode and scaling
- Check index-specific resolution and loading
- Validate actual receiver response before release
The ABB AO561 requires replacement verification of the output circuit, hardware index and receiver behavior before commissioning.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: These documents identify the ABB source edition and applicable output conditions. Terminal blocks, receivers and cables are included only when specified in the written quotation.
Features:
- AO561 source material distinguishes output mode and hardware-index conditions
- Software licensing and project backups remain the customer's responsibility
- Accessories are supplied only when listed in the quotation
Documentation for the ABB AO561 must match the receiver signal requirements and permitted load; confirm manual availability in the written quotation.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size13.4 × 7.3 × 4.3 cm
-
Shipping weight0.16 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference8538900000
-
OriginSwitzerland
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about AO561
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
Can both the voltage and current terminals of one AO561 channel feed different devices?
No. Only the terminals corresponding to the configured output mode may be connected. ABB warns that the voltage output is undefined in current mode and the current output is undefined in voltage mode. -
Why must the actuator remain safe while the 24 V supply ramps up?
ABB states that AO561 output is undefined when L+ is below 10 V. A slowly rising or falling supply can pass through that condition; the installation must prevent the resulting signal from causing unintended actuator movement. -
Can a 750 ohm receiver be driven directly in current-output mode?
It exceeds the documented 0 to 500 ohm load range. Check the complete receiver and cable burden before selecting AO561; do not assume a current output can maintain its command at any load resistance. -
How much load can a voltage receiver draw from AO561?
ABB specifies a maximum voltage-output load current of plus or minus 2 mA. Confirm the receiver input impedance and any parallel loads against that limit before connection. -
Is the output reference electrically separated from the rest of the module?
No. AO561 is specified without galvanic isolation. Review the receiver reference and grounding arrangement rather than assuming that its analog interface provides an isolation barrier. -
Which terminals does ABB use for an AO561 reference to MicroFlex e190?
The MicroFlex e190 manual shows AO561 terminal 13 connected to X3 pin 19 and terminal 17 to X3 pin 9. Follow that complete drive-specific diagram, including its shield instruction, and verify the configured input function before operation. -
Can an output-state LED confirm that the receiver is getting the requested analog value?
No dedicated indication of the analog output signal is specified. Measure the actual output under the intended load and compare it with the controller command and receiver indication during commissioning. -
What should MRO personnel check when a spare has a different hardware index?
Compare the index-specific resolution and electrical ratings. The ABB data sheet distinguishes 12-bit from 13-bit including-sign resolution at E0, and also changes power consumption; preserve the engineered signal scaling and validate the receiver response.
READY TO VERIFY YOUR PART?
Get a AO561 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
