
GATE/POWER MODULE BOARD
GATE/POWER MODULE BOARD
SIMOREG DRIVES
POWER-INTERFACE
GATING + SV(POWER-INTERFACE)
(C98043-A1601-L1)
Machinery Control
Series:MM430
Input Voltage:380–480V AC ±10%
Input Frequency:50/60Hz ±5%
Output Power:7.5 kW
C751-009 I/O Module
Digital Inputs (DI) : 8 × 24V DC
Digital Outputs:4 × Relay Outputs
AC capacity:≤250V
Operating Voltage DC:+24 VDC +10%
Power Consumption:≤5W
Storage Temperature:-10˚C- +60˚C
Rectifier interfaces Module
Rectifier interfaces Module
PER2 for infeed/regenerative
feedback Supply units
with Designs H and K 3 AC 500-575V
50/60 Hz and 660-690V 3AC
50/60 Hz
INVERTER CPU BOARD
Processor: Infineon C167xx-series
Flash EPROM: ≥1 MB
SRAM: 128‒512 KB data cache
EEPROM: 8‒16 KB
On-Board Power: +5VDC ±1%
Temperature operating:-15˚C to +70˚C
Replacement IPD card
SINAMICS S120
Replacement IPD card
for air-cooled Basic Line Module
1100kW 500-690V 3AC/1400A
Synchronous servo motor
SIMOTICS S synchronous servo motor
1FK7 Compact 6.0 Nm, 100K, 4500 rpm 1.74 kW
naturally cooled IM B5 (IM V1, IM V3)
power/signal connector plug rotatable by 270°
ABSOLUTE ENCODER 2048 P/REV (ENCODER A-2048)
WITH DRIVE-CLIQ INTERFACE
PERFORMANCE REDUCTION BY 10% DUE TO
ABSOLUTE ENCODER
PLAIN SHAFT, TOLERANCE N
WITH HOLDING BRAKE DEGREE
OF PROTECTION IP64
IGBT Silicon Module
Insulation Class:2500 V
Collector (DC Link) Voltage:1200 V
Emitter Voltage:1200 V
Collector Peak:≤1800 A
Isolation (DC Link):≥5.0 kV RMS
Short Circuit Peak Current Limit:≤1.8kA
Replacement IPD card
SINAMICS S120
Replacement IPD card
for air-cooled Motor Module
500-690V
450kW
Replacement IPD card
SINAMICS S150
Replacement IPD card
for air-cooled Motor Module
basic unit 380-480V
110kW
Replacement IPD card
SINAMICS S120
Replacement IPD card
for air-cooled Motor Module
500-690V, 710kW
Synchronous servo motor
SIMOTICS S synchronous servo motor
1FK7 Compact 11 Nm
100K 3000 rpm
2.29 kW naturally cooled IM B5 (IM V1, IM V3)
power/signal connector plug rotatable by 270°
ABSOLUTE ENCODER 2048 P/REV (ENCODER A-2048)
WITH DRIVE-CLIQ INTERFACE
PERFORMANCE REDUCTION
BY 10% DUE TO ABSOLUTE ENCODER
PLAIN SHAFT, TOLERANCE N
WITH HOLDING BRAKE DEGREE
OF PROTECTION IP64
Replacement IPD card
SINAMICS S120
Replacement IPD card
for air-cooled Basic Line Module
560kW 500-690V
3AC/680A
Replacement IPD card
SINAMICS S120
Replacement IPD card
for air-cooled Basic Line Module
560kW 500-690V
3AC/680A
HR 2-AXIS CONTROL-LOOP BLOCK
SIMODRIVE 611 UNIVERSAL
HR 2-AXIS CONTROL-LOOP BLOCK
INCREMENTAL ENCODER SIN/COS 1 VPP
ABSOLUTE VALUE ENCODER ENDAT
SPEED/TORQUE SETPOINT POSITIONING
EXPANDABLE BY OPTIONS
G120 Standard Control Unit
SINAMICS G120 CONTROL UNIT
CU240E-2 E-TYPE SAFETY INTEGRATED
STO RS485-INTERFACE
USS-PROTOCOL 6DI, 3DO, 2AI, 2AO
MAX 1F-DI PTC/KTY INTERFACE
USB- AND SD/MMC-INTERFACE
PROTECTION IP20
AMBIENT TEMP 0 TO +50 DEG C
WITHOUT POWER MODULE AND PANEL
Driver Board
HV-IGBT modules: 1900A
Input Voltage Range:+24V DC
Isolation Voltage:min. 4000 V RMS
IGBT Voltage Monitoring:±5%
Gate Drivers Per Phase:2 channels
IGBT-TRANSISTOR MODULE
IGBT-TRANSISTOR MODULE
PRECHARGING RESISTOR 2 X 18 OHM
Voltage: 1500 V
DC Collector Current:160 A
Rated Pulse Current:320 A
Operating Junction Temperature:-40°C to +150°C
Current Transformer
CURRENT TRANSFORMER
2000 AMP
15-24VDC
AC Input Range: 0–2000 A AC
Overload Capacity: 130% of Ipn for 10 sec
DC Voltage or Current:4–20 mA (Two-Wire Loop)
Input Voltage: 15–24 V DC ±10%
Power Consumption: <2 W
SINAMICS DC LINK ADAPTER
SINAMICS DC link adapter set
for multi-tier configuration
Screw terminals 35-95 mm2
for all Line/Motor Modules
BUSBAR CURRENT TRANSFORMER
Primary Current (Ipn): Range 50–600 A
Secondary Current (Isn):1 A or 5 A
Frequency: 50/60 Hz
Insulation Voltage:720 V AC
Operating: -25°C to +60°C
Storage: -40°C to +70°C
Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.