ABB Drives

Drive Control Board

Control Methods:DTC 
Communication:Embedded
Operating Voltage:24 V DC (±10%)
Power Consumption:30 W (typical)
Memory:512 MB DDR3 RAM, 4 GB Flash

Main Control Board

DCS880
SDCS-CON-H01
Main Control Board
Operating Voltage:24 V DC (±10%)
Current Consumption:≤1.5 A
Digital I/O Channels:32 optoisolated DC I/O points
Analog I/O:±10 V DC / 4–20 mA

ACS880 AC Drive- 500V, 3PH, wall mount, regenerative

LV AC industrial wall-mounted regenerative single drive
Input Supply:3-phase 380–480V AC (±10%), 50/60 Hz
Output Power:5.5 kW (7.5 HP) @ 400V AC
Output Current:21 A continuous (40°C ambient)
Overload Capacity:110% for 60s, 150% for 2s
Output Frequency:0–500 Hz (motor-dependent)
Efficiency:>98% (at full load)
Power Factor:0.98 (min)

Terminal base

Terminal base
For AC500 V3. 1 slot for communication module. 
2 Ethernet interfaces
1 serial interface
1 CAN interface (TB5610-2ETH)

Main Control Board

Processor:PowerPC 750GL @ 400 MHz
Memory:128 MB SDRAM
Control Capacity:Up to 60,000 function blocks
Operating Voltage:5V DC
MTBF:>500,000 hours 
Mounting:AC 800M controller baseplate

Operating Panel

Display:2-line LCD with backlight
Control Keys:Navigation keys + Start/Stop/Jog buttons
Operating Voltage:24V DC 
Power Consumption:≤ 5 W

Binary Input Module

Input Channels:16x 
Input Voltage:24/48/110/125V DC
Input Threshold (ON);>60% of rated voltage
Input Current :3–8 mA
Response Time:<5 ms 
Isolation:2.5 kV AC
Power Consumption:≤ 4 W

Relay Control module

Number of Channels: 8 independent channels
Number: 6 dedicated
Contact Rating: 24 V DC / 30 mA 
Voltage: +24 V DC nominal 
Power Consumption: < 5 W

Industrial Control Module

Input Channels:16 (Grouped as 8+8)
Input Voltage:24 V DC (Nominal)
Voltage Range:19–30 V DC (Logic "1": ≥15 V)
Logic "0" Threshold:≤5 V DC
Input Current:6 mA per channel (typical)
Isolation:500 V AC (channel-to-channel)
Backplane Power :5 V DC (via P4 baseplate)

CIRCUIT BOARD

Supply Voltage:24 V DC ±10% 
Power Consumption:≤5 W
Isolation :500 V AC 
I/O Channels:Likely 8–16
Function:Fieldbus interface or signal conditioning
Status:Discontinued

CIRCUIT BOARD

Input Voltage:24 V DC ±10%
Output Voltage(s):±15 V DC or 5 V DC
Power Rating:10–20 W 
Isolation:1500 V AC
Protections:Short-circuit, over-temperature

PC BOARD

PC BOARD
PULSE TRANSFORM UNIT
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-JB

DRIVE BOARD

DRIVE BOARD
TRIGGER PULSE
RESISTIVE NETWORK
YXU-168G

PC BOARD

PC BOARD
PULSE TRANSFORM UNIT
RESISTIVE NETWORK
YXU-168F

DRIVE BOARD

DRIVE BOARD
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-FK

PC BOARD

PC BOARD
COMPUTER UNIT
MULTI INPUT/OUTPUT
ON BOARD RAM
YT204001-JN

ANALOG OUTPUT BOARD

ANALOG OUTPUT BOARD
RESISTIVE NETWORK
STATUS LED INDICATOR
YT204001-AA

DIGITAL SPEED INPUT BOARD

DIGITAL SPEED INPUT BOARD
RESISTIVE NETWORK
STATUS LED INDICATOR
YT204001-FC

Communication Module

Data Rate:31.25 kbit/s
Power Supply:24 V DC (via controller backplane)
Power Consumption:Typically 0.8 W per channel
Isolation:500 V AC
RUN (Green): Module operation
COM (Green/Yellow): Communication status
ERR (Red): Fault indication

MEMORY BOARD

MEMORY BOARD
5.5 V
1 F
YT204001-DF

PC BOARD

PC BOARD
RESISTIVE NETWORK
STATUS LED INDICATORS
YPQ-103C

ACS800 Drive Board

Input Voltage:380–480 V AC
DC Link Voltage:540–650 V DC
Auxiliary Voltage:24 V DC
Product Line:ABB ACS800 Industrial Drives 
Isolation Voltage:2.5 kV AC

ACS800 Drive Board

Input Voltage:380–480 V AC (±10%)
DC Link Voltage:540–650 V DC
Protections:DC over/undervoltage
Auxiliary Voltage:24 V DC 
Isolation Voltage:2.5 kV AC

MAIN CIRCUIT INTERFACE BOARD

Input Voltage:200–480 V AC
DC Link Voltage:280–650 V DC 
Auxiliary Voltage 24 V DC
PWR (Green): 24V OK
RDY (Yellow): Drive ready
ERR (Red): Fault detected
Isolation Voltage:2.5 kV AC

IGCT Module

Configuration:Single IGCT
Voltage Rating:4500 V
Current Rating:1200 A 
Critical dv/dt:1000 V/μs (min.)
Isolation Voltage:10 kV RMS
Mounting Force:35–45 kN