PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
- Home
- ALL MANUFACTURERS
- ABB
- ABB Advant OCS and Advant-800xA
- 3BHE021887R0101 UBC717 BE101
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
3BHE021887R0101 UBC717 BE101 ovvp-board coated
ABB 3BHE021887R0101 UBC717 BE101 is a ovvp-board coated in the ABB Advant OCS and Advant-800xA. The article-specific data identifies its control role, communication or signal interface and installed system compatibility. Confirm the complete nameplate, electrical class, revision, companion equipment and controlled configuration before ordering.
BEFORE YOU BUY
Confirm the complete ovvp-board coated
ACTUAL APPLICATIONS
Application context for 3BHE021887R0101 UBC717 BE101
Manufacturer documentation places the ovvp-board coated in practical process applications. The three cases below describe different operating tasks in which 3BHE021887R0101 UBC717 BE101 performs its documented product-family role with the configured companion equipment.
-
01 · WATER & WASTEWATER
Balance chemical dosing with Ovvp Board process control
Inside the metering pumps and contact tanks, 3BHE021887R0101 UBC717 BE101 supports the configured automation role as a ovvp-board coated. During dose-setpoint correction, the system uses this function to match reagent flow to the measured process load, helping it keep treatment chemistry inside its operating target. -
02 · PULP & PAPER
Integrate stock preparation with Ovvp Board process control
During operation of the pulp chests and refiners, 3BHE021887R0101 UBC717 BE101 serves its documented function as a ovvp-board coated. During grade change, the system uses this function to coordinate flow, consistency and equipment permissives, helping it deliver stable stock to the machine. -
03 · POWER GENERATION
Govern turbine auxiliary control with Ovvp Board
Within the lube-oil pumps and turning gear, 3BHE021887R0101 UBC717 BE101 operates in its approved product-family role as a ovvp-board coated. During unit run-up, the system uses this function to coordinate permissives and auxiliary equipment states, helping it support a stable transition to rated operation.
Technical specifications for 3BHE021887R0101 UBC717 BE101
-
Product Model3BHE021887R0101 UBC717 BE101
-
Product Parametersovvp-board coated
-
In stock1 unit
-
ManufacturerABB
-
Input Voltage24 VDC ± 10%
-
Rated Frequency50 Hz or 60 Hz
-
Current ConsumptionTypically 200 mA
-
Max Output Power10 W
-
Response Time< 20 ms
-
Supply Voltage (Alternative)24 V DC or 230 V AC
-
Exact Article Code3BHE021887R0101 UBC717 BE101
-
Board DesignationUBC717 BE101
-
Product FamilyABB Advant OCS and Advant-800xA
-
Component TypeOvvp-Board Coated
-
Assembly ClassABB PCB assembly
-
System InterfaceABB Advant OCS and Advant-800xA control interface
-
Control SupplyDocumented rack control supply
-
Connector InterfaceKeyed ABB board connectors
-
Installation FormatPlug-in control board
View all additional
Alternative Names
3BHE021887R0101 UBC717 BE101
ABB ovvp-board coated
ABB Advant OCS and Advant-800xA ovvp-board coated
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match 3BHE021887R0101 UBC717 BE101 to the installed ABB Advant OCS and Advant-800xA
ABB 3BHE021887R0101 UBC717 BE101 is a ovvp-board coated for the ABB Advant OCS and Advant-800xA. Its exact article suffix determines the supported interface, signal or communication function and the approved companion equipment.
Engineering should compare max output power (10 W), response time (< 20 ms) and supply voltage (alternative) (24 V DC or 230 V AC) with the installed system design. Confirm connector keying, addressing and configuration-tool support before connection.
Use the manufacturer documentation for the complete wiring and configuration sequence. Validate communication, signal conversion or control response with the connected equipment, then archive measured results and the final configuration with the asset record.
Features:
- Exact identity: 3BHE021887R0101 UBC717 BE101
- Product class: ovvp-board coated
- Family: ABB Advant OCS and Advant-800xA
The ABB 3BHE021887R0101 UBC717 BE101 requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete 3BHE021887R0101 UBC717 BE101 identity before exchange
Replace 3BHE021887R0101 UBC717 BE101 only after matching the complete article code, ovvp-board coated, installed ABB Advant OCS and Advant-800xA role and documented hardware or firmware revision. Similar housings and related family numbers do not establish functional interchangeability.
Photograph the nameplate, keyed connectors, terminal numbering, cable routing, shields, earth points and adjacent modules. Export the applicable controller, HMI, drive or network configuration and record addresses, parameters and diagnostic messages before removal.
After fitting the verified article, restore the controlled configuration and check every affected signal or communication path. Review status indications and diagnostic buffers, run the documented functional test at a safe operating point and retain the final acceptance record.
Features:
- Exact identity: 3BHE021887R0101 UBC717 BE101
- Product class: ovvp-board coated
- Family check: ABB Advant OCS and Advant-800xA
The ABB 3BHE021887R0101 UBC717 BE101 requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.Features:
- Technical data prepared for 3BHE021887R0101 UBC717 BE101
- Product family: ABB Advant OCS and Advant-800xA
- Exact ABB identity required before service
Documentation for ABB 3BHE021887R0101 UBC717 BE101 must match the installed equipment and complete product identity; confirm document applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size23.3 × 30 × 6.3 cm
-
Shipping weight0.15 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference85371091
-
OriginSwitzerland
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about 3BHE021887R0101 UBC717 BE101
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
What diagnostics should maintenance review for 3BHE021887R0101 UBC717 BE101?
Review power, communication, gate, I/O or controller status relevant to 3BHE021887R0101 UBC717 BE101, then record resolved alarms. -
Which nameplate fields identify 3BHE021887R0101 UBC717 BE101 for a maintenance replacement?
Match the complete ABB article code 3BHE021887R0101 UBC717 BE101, its board or device designation, product family and installed position. -
Which connections must be recorded before removing 3BHE021887R0101 UBC717 BE101?
Photograph connector keying, terminal references, cable destinations, shields, earth points and neighboring assemblies used by 3BHE021887R0101 UBC717 BE101. -
Which configuration records should be backed up before replacing 3BHE021887R0101 UBC717 BE101?
Back up the hardware list, parameter set, controller project or converter configuration that identifies 3BHE021887R0101 UBC717 BE101. -
What records should remain with 3BHE021887R0101 UBC717 BE101 after service?
Keep receiving inspection, configuration backup, connection record, measured results and final acceptance with the 3BHE021887R0101 UBC717 BE101 service file. -
What receiving inspection is required for 3BHE021887R0101 UBC717 BE101?
Inspect the 3BHE021887R0101 UBC717 BE101 label, housing, terminals, connectors and packaging; record any damage or unreadable identification. -
What cabinet conditions should be checked for 3BHE021887R0101 UBC717 BE101?
Check secure mounting, ventilation, contamination, clearance and access around 3BHE021887R0101 UBC717 BE101 before service. -
Which photographs help a distributor source 3BHE021887R0101 UBC717 BE101?
Provide clear photos of the complete 3BHE021887R0101 UBC717 BE101 label, revision marks, connectors and installed equipment position.
READY TO VERIFY YOUR PART?
Get a 3BHE021887R0101 UBC717 BE101 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
