PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
- Home
- ALL MANUFACTURERS
- ABB
- ABB Advant OCS and Advant-800xA
- ABB AC 800PEC
- 3BHE024747R0101 GDC801A
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
3BHE024747R0101 GDC801A rigi crowbar drive pcb
ABB 3BHE024747R0101 GDC801A is a rigi crowbar drive pcb in the ABB AC 800PEC. The article-specific data identifies its control role, communication or signal interface and installed system compatibility. Confirm the complete nameplate, electrical class, revision, companion equipment and controlled configuration before ordering.
BEFORE YOU BUY
Confirm the complete rigi crowbar drive pcb
ACTUAL APPLICATIONS
Application context for 3BHE024747R0101 GDC801A
Manufacturer documentation places the rigi crowbar drive pcb in practical drive applications. The three cases below describe different operating tasks in which 3BHE024747R0101 GDC801A performs its documented product-family role with the configured companion equipment.
-
01 · OIL & GAS
Coordinate cooling-fan control with Rigi Crowbar
At the control layer of the air coolers, fan motors and temperature feedback, 3BHE024747R0101 GDC801A supports the configured automation role as a rigi crowbar drive pcb. During ambient-load change, the system uses this function to trim fan speed to the measured cooling requirement, helping it hold outlet temperature without unnecessary fan power. -
02 · PULP & PAPER
Coordinate dryer-section control with Rigi Crowbar
As part of the steam groups and dryer drives, 3BHE024747R0101 GDC801A handles its designated signal or control duty as a rigi crowbar drive pcb. During moisture correction, the system uses this function to align thermal and drive response with the running sheet, helping it support the target moisture profile. -
03 · AUTOMOTIVE
Align body transfer with Rigi Crowbar process control
At the control layer of the skid conveyors and lift stations, 3BHE024747R0101 GDC801A serves its documented function as a rigi crowbar drive pcb. During model change, the system uses this function to coordinate motion requests and station interlocks, helping it keep the assembly takt moving.
Technical specifications for 3BHE024747R0101 GDC801A
-
Product Model3BHE024747R0101 GDC801A
-
Product Parametersrigi crowbar drive pcb
-
In stock1 unit
-
Estimated Shipping Size20.7x18.4x3.5cm
-
ManufacturerABB
-
Weight0.55 kg
-
Power Supply24V
-
Exact Article Code3BHE024747R0101 GDC801A
-
Board DesignationGDC801A
-
Product FamilyABB AC 800PEC
-
Component TypeRigi Crowbar Drive Pcb
-
Assembly ClassABB PCB assembly
-
System InterfaceABB AC 800PEC control interface
-
Control SupplyDocumented rack control supply
-
Connector InterfaceKeyed ABB board connectors
-
Installation FormatPlug-in control board
-
Signal DomainControl and diagnostic signals
-
Service PositionDocumented rack slot
-
Configuration BasisInstalled ABB hardware list
-
Replacement BasisExact article and board revision
-
Protective CheckESD and protective-earth control
View all additional
Alternative Names
3BHE024747R0101 GDC801A
ABB rigi crowbar drive pcb
ABB AC 800PEC rigi crowbar drive pcb
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match 3BHE024747R0101 GDC801A to the installed ABB AC 800PEC
ABB 3BHE024747R0101 GDC801A is a rigi crowbar drive pcb for the ABB AC 800PEC. Its exact article suffix determines the supported interface, signal or communication function and the approved companion equipment.
Engineering should compare product family (ABB AC 800PEC), component type (Rigi Crowbar Drive Pcb) and assembly class (ABB PCB assembly) with the installed system design. Confirm connector keying, addressing and configuration-tool support before connection.
Use the manufacturer documentation for the complete wiring and configuration sequence. Validate communication, signal conversion or control response with the connected equipment, then archive measured results and the final configuration with the asset record.
Features:
- Exact identity: 3BHE024747R0101 GDC801A
- Product class: rigi crowbar drive pcb
- Family: ABB AC 800PEC
The ABB 3BHE024747R0101 GDC801A requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete 3BHE024747R0101 GDC801A identity before exchange
Replace 3BHE024747R0101 GDC801A only after matching the complete article code, rigi crowbar drive pcb, installed ABB AC 800PEC role and documented hardware or firmware revision. Similar housings and related family numbers do not establish functional interchangeability.
Photograph the nameplate, keyed connectors, terminal numbering, cable routing, shields, earth points and adjacent modules. Export the applicable controller, HMI, drive or network configuration and record addresses, parameters and diagnostic messages before removal.
After fitting the verified article, restore the controlled configuration and check every affected signal or communication path. Review status indications and diagnostic buffers, run the documented functional test at a safe operating point and retain the final acceptance record.
Features:
- Exact identity: 3BHE024747R0101 GDC801A
- Product class: rigi crowbar drive pcb
- Family check: ABB AC 800PEC
The ABB 3BHE024747R0101 GDC801A requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.Features:
- Technical data prepared for 3BHE024747R0101 GDC801A
- Product family: ABB AC 800PEC
- Exact ABB identity required before service
Documentation for ABB 3BHE024747R0101 GDC801A must match the installed equipment and complete product identity; confirm document applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size28 × 22 × 10 cm
-
Shipping weight0.40 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference85371091
-
OriginSwitzerland
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about 3BHE024747R0101 GDC801A
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
Which nameplate fields identify 3BHE024747R0101 GDC801A for a maintenance replacement?
Match the complete ABB article code 3BHE024747R0101 GDC801A, its board or device designation, product family and installed position. -
Which connections must be recorded before removing 3BHE024747R0101 GDC801A?
Photograph connector keying, terminal references, cable destinations, shields, earth points and neighboring assemblies used by 3BHE024747R0101 GDC801A. -
Which configuration records should be backed up before replacing 3BHE024747R0101 GDC801A?
Back up the hardware list, parameter set, controller project or converter configuration that identifies 3BHE024747R0101 GDC801A. -
What records should remain with 3BHE024747R0101 GDC801A after service?
Keep receiving inspection, configuration backup, connection record, measured results and final acceptance with the 3BHE024747R0101 GDC801A service file. -
What receiving inspection is required for 3BHE024747R0101 GDC801A?
Inspect the 3BHE024747R0101 GDC801A label, housing, terminals, connectors and packaging; record any damage or unreadable identification. -
What cabinet conditions should be checked for 3BHE024747R0101 GDC801A?
Check secure mounting, ventilation, contamination, clearance and access around 3BHE024747R0101 GDC801A before service. -
Which photographs help a distributor source 3BHE024747R0101 GDC801A?
Provide clear photos of the complete 3BHE024747R0101 GDC801A label, revision marks, connectors and installed equipment position. -
How should a distributor quote the exact 3BHE024747R0101 GDC801A assembly?
Quote ABB 3BHE024747R0101 GDC801A, quantity, product family, visible revision marks and the destination equipment in the request.
READY TO VERIFY YOUR PART?
Get a 3BHE024747R0101 GDC801A quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
