PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
- Home
- ALL MANUFACTURERS
- ABB
- ABB Advant OCS and Advant-800xA
- ABB AC 800PEC
- 3BSE018137R1 CI858-1
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
3BSE018137R1 CI858-1 drivebus interface module
ABB 3BSE018137R1 CI858-1 is a drivebus interface module in the ABB AC 800PEC. The article-specific data identifies its control role, communication or signal interface and installed system compatibility. Confirm the complete nameplate, electrical class, revision, companion equipment and controlled configuration before ordering.
BEFORE YOU BUY
Confirm the complete drivebus interface module
ACTUAL APPLICATIONS
Application context for 3BSE018137R1 CI858-1
Manufacturer documentation places the drivebus interface module in practical drive applications. The three cases below describe different operating tasks in which 3BSE018137R1 CI858-1 performs its documented product-family role with the configured companion equipment.
-
01 · OIL & GAS
Observe cooling-fan control with Drivebus Interface
Within the air coolers, fan motors and temperature feedback, 3BSE018137R1 CI858-1 handles its designated signal or control duty as a drivebus interface module. During ambient-load change, the system uses this function to trim fan speed to the measured cooling requirement, helping it hold outlet temperature without unnecessary fan power. -
02 · WATER & WASTEWATER
Monitor aeration-blower output with Drivebus Interface
Across the blower motors, air headers and oxygen-control loops, 3BSE018137R1 CI858-1 operates in its approved product-family role as a drivebus interface module. During oxygen-setpoint change, the system uses this function to coordinate blower speed with the required air delivery, helping it match aeration energy to treatment demand. -
03 · AUTOMOTIVE
Regulate paint-shop conveying with Drivebus Interface
Within the carrier tracking and booth interfaces, 3BSE018137R1 CI858-1 handles its designated signal or control duty as a drivebus interface module. During carrier accumulation, the system uses this function to route carriers by production status, helping it preserve body order through the process.
Technical specifications for 3BSE018137R1 CI858-1
-
Product Model3BSE018137R1 CI858-1
-
Product Parametersdrivebus interface module
-
In stock1 unit
-
ManufacturerABB
-
Operating temperature-20°C to +60°C
-
Storage temperature-40°C to +85°C
-
Humidity5-95% RH (non-condensing)
-
Data rate10 Mbps
-
Max. distance100m (fiber length)
-
Supply voltage24 VDC (±10%)
-
Power consumption<5 W
-
Isolation1500 VAC
-
Exact Article Code3BSE018137R1 CI858-1
-
Board DesignationCI858-1
-
Product FamilyABB AC 800PEC
-
Component TypeDrivebus Interface Module
-
Assembly ClassABB PCB assembly
-
System InterfaceABB AC 800PEC control interface
-
Control SupplyDocumented rack control supply
View all additional
Alternative Names
3BSE018137R1 CI858 1
ABB drivebus interface module
ABB AC 800PEC drivebus interface module
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match 3BSE018137R1 CI858-1 to the installed ABB AC 800PEC
ABB 3BSE018137R1 CI858-1 is a drivebus interface module for the ABB AC 800PEC. Its exact article suffix determines the supported interface, signal or communication function and the approved companion equipment.
Engineering should compare data rate (10 Mbps), max. distance (100m (fiber length)) and supply voltage (24 VDC (±10%)) with the installed system design. Confirm connector keying, addressing and configuration-tool support before connection.
Use the manufacturer documentation for the complete wiring and configuration sequence. Validate communication, signal conversion or control response with the connected equipment, then archive measured results and the final configuration with the asset record.
Features:
- Exact identity: 3BSE018137R1 CI858-1
- Product class: drivebus interface module
- Family: ABB AC 800PEC
The ABB 3BSE018137R1 CI858-1 requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete 3BSE018137R1 CI858-1 identity before exchange
Replace 3BSE018137R1 CI858-1 only after matching the complete article code, drivebus interface module, installed ABB AC 800PEC role and documented hardware or firmware revision. Similar housings and related family numbers do not establish functional interchangeability.
Photograph the nameplate, keyed connectors, terminal numbering, cable routing, shields, earth points and adjacent modules. Export the applicable controller, HMI, drive or network configuration and record addresses, parameters and diagnostic messages before removal.
After fitting the verified article, restore the controlled configuration and check every affected signal or communication path. Review status indications and diagnostic buffers, run the documented functional test at a safe operating point and retain the final acceptance record.
Features:
- Exact identity: 3BSE018137R1 CI858-1
- Product class: drivebus interface module
- Family check: ABB AC 800PEC
The ABB 3BSE018137R1 CI858-1 requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.
Features:
- Technical data prepared for 3BSE018137R1 CI858-1
- Product family: ABB AC 800PEC
- Exact ABB identity required before service
Documentation for ABB 3BSE018137R1 CI858-1 must match the installed equipment and complete product identity; confirm document applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size23.3 × 30 × 6.3 cm
-
Shipping weight0.76 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference85371091
-
OriginSwitzerland
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about 3BSE018137R1 CI858-1
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
Which photographs help a distributor source 3BSE018137R1 CI858-1?
Provide clear photos of the complete 3BSE018137R1 CI858-1 label, revision marks, connectors and installed equipment position. -
How should a distributor quote the exact 3BSE018137R1 CI858-1 assembly?
Quote ABB 3BSE018137R1 CI858-1, quantity, product family, visible revision marks and the destination equipment in the request. -
Which ABB system documents apply to 3BSE018137R1 CI858-1?
Use ABB documentation for ABB AC 800PEC and confirm that the exact 3BSE018137R1 CI858-1 assembly is covered by the hardware scope. -
How should the signal or power interface for 3BSE018137R1 CI858-1 be verified?
Compare every connected circuit with the controlled drawing and verify the approved electrical class before connecting 3BSE018137R1 CI858-1. -
Which electrical checks apply before energising 3BSE018137R1 CI858-1?
Confirm the documented supply, interface, insulation condition and protective earth before energising 3BSE018137R1 CI858-1. -
What commissioning evidence is needed after fitting 3BSE018137R1 CI858-1?
Record power-up status, diagnostics, the affected function test and final maintenance approval for 3BSE018137R1 CI858-1. -
Which companion hardware must match 3BSE018137R1 CI858-1?
Verify the documented rack, control unit, power stage, connector assembly and adjacent hardware paired with 3BSE018137R1 CI858-1. -
What drawings should engineering review before installing 3BSE018137R1 CI858-1?
Review the installed hardware list, cabinet drawing, connection diagram and controlled ABB AC 800PEC service documentation for 3BSE018137R1 CI858-1.
READY TO VERIFY YOUR PART?
Get a 3BSE018137R1 CI858-1 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
