
























Kindly Reminder
Can't Find Your Required Components?
If your specific control system parts are not listed on our website, contact us immediately.
Our procurement specialists will source genuine new components tailored to your technical requirements.
All Amikon-supplied automation parts include:
12 Months Warranty
24h /7 online Service ( info@amikon.cn | +86 18020776786 )
Original new Factory Sealed
DIGITAL I/O MODULE CABLE
1492CABLE025TBCH
DIGITAL I/O MODULE
READY CABLE
40 CONDUCTORS
18 AWG
300 VAC
DIGITAL CABLE CONNECTION PRODUCTS
CABLE WITH 36-POINT 1756-TBCH WIRING ARM
2.5 METER (8.2 FEET)
CABLE ASSEMBLY
1492CABLE025TBNH
CABLE ASSEMBLY
PRE-WIRED REMOVABLE TERMINAL BLOCK
1756-TBNH
20 CONDUCTOR
2.5 METER CABLE LENGTH
FOR 1756 DIGITAL I/O MODULE
Thermocouple I/O Module
1797IRT8
INPUT MODULE
FLEX EX
THERMOCOUPLE / RTD INPUT
8 CHANNEL
INTERNAL BUS CONFIGURABLE
40-100 MV
IP20
Overload Relay
COMMUNICATION MODULE
E300 OVERLOAD RELAYS
IEC
DEVICENET
193/592 IEC/NEMA
Current/Ground Fault Sensing Module
Current/Ground Fault Sensing Module
for E300 Overload Relays,
0.5-30A
DIN Rail / Panel Mount,
with Line- and Load-Side Power Conductor Terminals,
Directly Replaces 193-ECPM2
Series A
Isolated Analog Output Module
1794OF4I
ANALOG OUTPUT MODULE
FLEX I/O
4 CHANNEL
0-20 MA
24 VDC
16 BIT RESOLUTION
TB2/TB3/TB3S/TB3T/TB3TS/TBN TERMINAL BASE
SCREW CONNECTION
Flex 16 Point Digital Input Module
Number of inputs:16, nonisolated
On-state voltage, min:159V AC
On-state voltage, nom:240V AC
On-state voltage, max:264V AC
On-state current, min:5.30 mA
On-state current, max:13.29 mA
Nominal input impedance:22.2 kΩ
Nominal input current:11 mA @ 240V AC
Flexbus current:32 mA @ 5V DC
Power dissipation, max:6 W @ 264V AC
Flex 16 Point Digital Output Module
Number of I/O channels:16, nonisolated
On-state current:50 mA min per output
Surge current:7 A for 40 ms each
Off-state leakage, max:2.5 mA
Field Bus current:116 mA
Power dissipation, max:6 W @ 264V AC
Thermal dissipation, max:20.47 BTU/hr @ 264V AC
Flex Controlnet Adapter
1794ACNR15
NETWORK ADAPTER
FLEX I/O
CONTROLNET
DUAL MEDIA
24 VDC
OPEN STYLE
DIN RAIL MOUNT
Flex 8 Point Relay Output Module
1794OW8
OUTPUT MODULE
8 POINT
ISOLATED RELAY CONTACTS
5.5 W
2 AMP
230 VAC
125 VDC
FLEX I/O
Tariff Code: 8538907080
Country of Origin: United States
Flex I/O communication adapter
1794ACN15
ADAPTER
COMMUNICATION/NETWORK
FLEX I/O TO CONTROLNET
24 VDC
OPEN STYLE
DIN MOUNT
IP20
REPEATER ADAPTOR
1786RPA
REPEATER ADAPTOR
CONTROLNET
COMMUNICATION MODULE
24 V DC
COAXIAL BNC
SINGLE CONNECTOR
DIN RAIL MOUNTING
ControlNet Fiber Ring Medium Repeater
1786RPFM
RING REPEATER
CONTROLNET
DUAL FIBER OPTIC CHANNEL
DIN RAIL MOUNTING
FIBER OPTIC
USE TO 3000 M
FOR 62.5/125 UM MULTI-MODE
Stratix 6000 8 port Managed Switch
Transmission speed:10/100 Mbps
No. of Ports:Eight (8)
Series:Stratix 5700
Part Number:1783-EMS08T
Product type:Managed Ethernet switch
Copper ports:8
Fiber port:1
Input voltage:12 to 48 Volts DC
Peak power dissipation:5.8 Watts
Peak thermal dissipation:24.6 BTU / hour
1715 EtherNet/IP Comms Adaptor Module
Product Line Bulletin:1715 Redundant I/O module
Communication Module:Ethernet/IP Adapter
Module Type:EtherNet/IP Adapter
Modules supported:24 per Adapter Pair
Wire Size:12 AWG
Power Dissipation:8 Watts
Flex 8 Thermocouple Input Module
Power Dissipation:3W maximum @ 31.2V
Resolution:16 bits (2.384 microvolts typical)
Product Type:Thermocouple / milivolt Input Module
Product Family:Flex I/O Modules
millivolt signal: +/- 76. 5mV
Data Format:16-bit 2’s complement or offset binary (unipolar)
Indicator:1 red/green power status indicator
CJC unit:A-B Part Number 969424–0

Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.