PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
- Home
- ALL MANUFACTURERS
- Bently Nevada
- 3500 System
- 86497-01-02-02-00
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
86497-01-02-02-00 monitoring interface module
Bently Nevada 86497-01-02-02-00 is a monitoring interface module for the 3500 System. It is used to 0-95% RH (non-condensing). Confirm the complete article identity, electrical limits, interfaces, companion hardware and controlled commissioning procedure before ordering.
BEFORE YOU BUY
Confirm the complete monitoring interface module
ACTUAL APPLICATIONS
Application context for 86497-01-02-02-00
Manufacturer documentation places the Monitoring Interface Module in practical vibration applications. The three cases below describe different operating tasks in which 86497-01-02-02-00 performs its documented product-family role with the configured companion equipment.
- 01 · OIL & GAS
Monitor reciprocating compressor condition with Monitoring Interface
During operation of the cylinder, rod-position and casing sensors, 86497-01-02-02-00 supports the configured automation role as a Monitoring Interface Module. During process-gas transition, the system uses this function to associate mechanical signals with the compression cycle, helping it separate process influence from a developing mechanical fault. - 02 · POWER GENERATION
Observe large-pump diagnostics with Monitoring Interface
During operation of the pump shafts, bearings and driver trains, 86497-01-02-02-00 handles its designated signal or control duty as a Monitoring Interface Module. During process transient, the system uses this function to compare the channel response through the changing condition, helping it support protection decisions during the transient. - 03 · MINING & METALS
Verify process-fan protection with Monitoring Interface
For the coordinated operation of the fan bearings, shaft probes and motor frames, 86497-01-02-02-00 handles its designated signal or control duty as a Monitoring Interface Module. During gas-flow adjustment, the system uses this function to observe rotor and casing behavior as fan duty changes, helping it protect a rotating asset that supports continuous production.
Technical specifications for 86497-01-02-02-00
-
Product Model86497-01-02-02-00
-
Product Parametersmonitoring interface module
-
In stock1 unit
-
ManufacturerBently Nevada
-
Operating Temperature-40°C to +70°C
-
Storage Temperature-50°C to +85°C
-
Humidity0-95% RH (non-condensing)
-
Vibration Resistance5g (10-500Hz)
-
Exact Part Number86497-01-02-02-00
-
Product Family3500 System
-
Component TypeMonitoring Interface Module
-
Channel Capacity2 channels
-
Rack SpaceOne full-height slot
-
Backplane Supply3500/3300 rack power
-
Input TypeCondition-monitoring transducer
-
Alarm OutputsAlert and Danger levels
-
Status LEDsOK, TX/RX and Bypass
-
Buffered OutputFront-panel transducer signal
-
ConfigurationRack configuration software
View all additional
Alternative Names
86497 01 02 02 00
3500 System monitoring interface module
Bently Nevada monitoring interface module
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match 86497-01-02-02-00 to the installed 3500 System
Bently Nevada 86497-01-02-02-00 is a monitoring interface module used in the 3500 System. Use 86497-01-02-02-00 in the documented 3500 System measurement or protection channel. Match the exact order code, installed position, signal range and monitored machine function before work.
Photograph terminals, coaxial connectors, shields, earth points, rack slot and adjacent hardware before removing 86497-01-02-02-00. Restore each connection to the controlled drawing. Confirm 86497-01-02-02-00, 3500 system, the exact mechanical position and the approved system configuration before connection.
After installing 86497-01-02-02-00, check transducer supply, gap or zero, signal response, alarms and rack diagnostics. Record the measured values before releasing the machine channel. Use qualified personnel, keep the applicable manufacturer instructions at the work location and retain the measured results with the equipment service record.
Features:
- Exact identity: 86497-01-02-02-00
- Product class: monitoring interface module
- Family: 3500 System
The Bently Nevada 86497-01-02-02-00 requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete 86497-01-02-02-00 identity before exchange
Replace 86497-01-02-02-00 only after matching the full article identity, monitoring interface module, installed 2 channels and documented system role. A similar family name or physical outline does not establish interchangeability.
Before removal, photograph the product label, mounting position, 3500/3300 rack power, cable routing, shields, earth connections and adjacent assemblies. Preserve the approved configuration or parameter backup for recovery.
After installation, restore all controlled settings and complete rack configuration software. Review status indications and diagnostics, test the affected function at a safe operating point, and record the final maintenance acceptance evidence.
Features:
- Exact identity: 86497-01-02-02-00
- Connection: 3500/3300 rack power
- Test: Rack configuration software
The Bently Nevada 86497-01-02-02-00 requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.Features:
- Technical values prepared for 86497-01-02-02-00
- Bently Nevada documentation matched to 3500 System
- Exact product identity required before service
Documentation for Bently Nevada 86497-01-02-02-00 must match the installed equipment and complete product identity; confirm manual applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size33 × 23.4 × 9.5cm
-
Shipping weight1.7 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference8537101190
-
OriginUSA
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about 86497-01-02-02-00
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
What receiving photos help verify 86497-01-02-02-00?
Ask for front, rear, connector and full-nameplate photos that show the complete 86497-01-02-02-00 identity. -
How should maintenance verify the installed family for 86497-01-02-02-00?
Confirm that 86497-01-02-02-00 is listed for the installed 3500 System hardware and configuration. -
What power and grounding checks apply to 86497-01-02-02-00?
Isolate energy, verify the documented supply, protective earth and shield termination before energising 86497-01-02-02-00. -
Which calibration values should be retained for 86497-01-02-02-00?
Retain scale factor, linear range, frequency response, probe gap or channel configuration values used with 86497-01-02-02-00. -
Which connection photographs are required before removing 86497-01-02-02-00?
Capture the label, rack position, terminals, coaxial connectors, shields, earth points and adjacent hardware for 86497-01-02-02-00. -
Which documents should accompany a quotation for 86497-01-02-02-00?
Request the data sheet, installation instructions and an applicable manufacturer manual for 86497-01-02-02-00 when available. -
How should the monitored machine channel be protected during a 86497-01-02-02-00 exchange?
Bypass or trip-manage the affected protection channel under the approved site procedure before exchanging 86497-01-02-02-00. -
What signal-range checks should engineering complete for 86497-01-02-02-00?
Compare the documented input, output, range and frequency values for 86497-01-02-02-00 with the installed channel.
READY TO VERIFY YOUR PART?
Get a 86497-01-02-02-00 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
