Honeywell

FTE BRIDGE MODULE

Communication Protocol Ethernet
with fault-tolerant mechanisms
Redundancy Support
Dual redundant communication paths
Input Voltage 24 VDC or 120/240 VAC
Power Consumption Low power, typically under 10 W
Operating Temperature Range  -20°C to +60°C
Storage Temperature Range -40°C to +85°C
Humidity 5% to 95% non-condensing

Sub-D to Knife terminals FTA

37-pole sub-D male connector 
(CN1) that must be connected 
with (16) RUSIO channelsl 16 sets 
of two knife terminals for the sixteen channels
Each channel has a the following knife 
terminal connections:l A+ terminal that is the (RUSIO) 
signal connection.l A- terminal that is 
the common 0 Volt connection.

Earth Fault Monitor

Temperature -40°C to +75°C
(-40°F to +167°F )
Approvals CE, TUV
DIN EN rails: TS32 / TS35 x 7.5
Input voltage:24 VDC +30/-15% 
Input current:10 mA maximum 25 mA
Voltage typically +4.1 VDC
Resistor (R)approximately 2.8 kOhm

PWA / I/O LINK MODULE

Module Type I/O Link Module 
Power Supply 24 VDC 
Operating Temperature -20°C to +60°C
Storage Temperature -40°C to +85°C
Humidity 5% to 95% non-condensing

Interface Board

TDC3000
TDC3000 framework
5 VDC
Approx. 1.5 W
300 mA (nominal)
TDC-specific protocols for 
data transfer and communication

WSI2 Unix coprocessor card

100 MHz
without graphics
used in the UxS and AxM.
with 32, 64, or 128 MB of RAM memory

Tpdgc I/O Circuit Board

TPDG I/O BOARD
INTERFACE FOR PERIPHERALS
6 PERIPHERAL CONNECTIONS  

CIRCUIT BOARD

TDC 3000 systems
Input Voltage: 24 V DC (typical)
Power Consumption: ≤10W
Operating Temperature: -20°C to +70°C
Storage Temperature: -40°C to +85°C

Interface Converter Board

24V DC internal power supply 
within the system
-20 ° C to 70 ° C
5% to 95%, no condensation
Multiple digital/analog input/output interfaces
DIN rail installation or rack mounted installation

Control Card

Voltage: 24 VDC (±10%)
Channel-to-Channel: 250 VAC minimum
Channel-to-Bus: 500 VAC reinforced isolation
Channels: 8 or 16
Resolution: 16-bit 
Accuracy: ±0.1% of full scale
Operating Temperature: -40°C to +70°C (-40°F to +158°F)
Humidity: 0–95% RH, non-condensing

RACK 10 SLOT

TKFXX102
RACK 10SLOT COATED
5.1VDC - 15/6AMP
24VDC - 2.8/2.8AMP
3.3VDC - 4/4AMP

MPU TRANSITION MODULE

TMPU1002
DISCONTINUED BY MANUFACTURER
MPU TRANSITION MODULE
COPPER TRANS MOD FOR EXTREME ENG CPU 18-410051-001 DUAL DIODE MODULE
DIN
6A DUAL DIODE MODULE

UCN Series Module

Output Frequency:50 kHz
Processing Capacity:High-speed data processing
Communication Protocol:Supports multiple industry-standard protocols
Operating Temperature:-40°C to +70°C
Memory Size:Extended memory capacity for enhanced system functionality

Low Level Analog Mux Module

Manufacturer : Honeywell
Product No. : 51309218-125
Product type : Low Level Analog Input Multiplexer RTD FTA
Not CE compliant, not conformally coated
Redundancy not supported
Input channels : 16
Teminals : compression
LLMux RTD FTA with compression terminals
Single IOP interface

Digital Input Power Module

Pulse Input FTA - MC-TPIX52
CE compliant, conformally coated
Use with IOP MU-PPIX02 or MC-PPIX02
Redundancy not supported
Input Points - 8
Terminals - Screw
Size B - 12 inches (307 mm)

Analog Input Module

Low Level Multiplexer Thermocouple FTA - MC-TAMT13
CE compliant, conformally coated
Redundancy not supported
Input channels - 16
Teminals - compression
Size B - 12 inches (307 mm)

Purbo Peripheral Display Generator

Temp: 0°C to 50°C
Power: Standard Honeywell supply
Humidity: 5% - 90% RH
Refresh: Real-time
Type: DCS Display

MEMORY BOARD

Model: 51401072-300
Type: Memory Board
Function:  Used in process control systems
System Compatibility: Honeywell TDC 3000 Process Control System
Operating Temperature Range: 0°C to 60°C (32°F to 140°F)

CONTROL BOARD

51401551301
CONTROL BOARD
K2LCN-3
MULTI INPUT/OUTPUT
PANEL MOUNT
SINGLE SLOT

Digital Input Module

Input Channels:32
Galvanic Isolation:1000 VAC RMS
Isolation Technique:Optical (in IOM)
DI Power Voltage Range:18 to 30 VDC
ON Sense Voltage/Current:13 VDC (min) or 3 mA (min)
OFF Sense Voltage/Current:5 VDC (max) or 1.2 mA (max)
Input Impedance:4.2 K
Absolute Delay Across Input Filter and Isolation:5 ms ± 20%

SC S300 SAFETY CONTROLLER

Safety Standard Compliance 
IEC 61508 SIL3, ISO 13849-1
Operating Voltage 24 VDC
Power Consumption <15 W
Operating Temperature -10°C to +60°C
Storage Temperature -40°C to +85°C
Mounting Options DIN rail or panel mount

FTA interconnection cable

System Interconnection Cable For Chassis IO
FS-SICC-0001/Lx (where × = length)
20 × AWG 22 (= 0.34 mm²) double shielded
9.93 mm / 0.39 in
3 = 3m