ABB Bailey

E/I Converter

Input Signal:Voltage: 0-5V, 0-10V
Input Impedance:≥ 100 kΩ
Output Signal:Current: 0-20mA, 4-20mA
Output Load;0–850 Ω (for 20mA max)
Power Supply:20-30V DC (typical)
Power Consumption:< 1.5W (typical)
Accuracy:±0.1% of span (typical @ 25°C)

E/I Converter

Input Signal: 0-10 V DC 
(configurable depending on system requirements)
Output Signal: Standard 4-20 mA current loop
Accuracy: ±0.1% of full-scale value
Load Impedance: 0-600 Ω for 
current loop compatibility
Response Time: <10 ms

Transfer Relay Delay

Contact Configuration:
1 NO (Normally Open)
1 NC (Normally Closed)
Contact Rating:
AC: 250V AC, 10A (resistive)
DC: 24V DC, 10A (resistive)
Coil Voltage: 24V DC (Nominal)

Transfer Relay

AC: 250V AC, 10A 
DC: 24V DC, 10A 
Coil Voltage: 24V DC (Nominal)
Contact Material: Silver alloy for 
low contact resistance and enhanced durability
Switching Time: <10 ms 
Mechanical Life: 10 million operations
Electrical Life: 100,000 operations at rated load

Signal Monitor

Voltage: 24-240V AC/DC
Current: 0.1-5A AC 
Typically ≤ 1 ms 
Frequency:50/60 Hz (±10%) 
Contact Rating:5-8A @ 250V AC 
Power Consumption:< 3 VA

Signal Monitor

Voltage: 24-240V AC/DC
Current: 0.1-5A AC
Frequency:50/60 Hz (±10%)
Contact Rating:5-8A @ 250V AC
Isolation Voltage:2500V AC
Power Consumption:< 3 VA (typical)

118VAC Auxiliary Relay

Coil Voltage:118V AC (50/60 Hz)
Operate Voltage:80% of nominal voltage
Release Voltage:20% of nominal voltage
Coil Power Consumption: 2.2 VA
Operate Time:< 20 ms
Release Time:< 15 ms
Mechanical Life:10 x 10⁶ operations

24 AUX Relay

Coil Voltage:24V DC
Operate Voltage:80% of nominal voltage
Release Voltage:10% of nominal voltage
Coil Power Consumption:1.8 W (typical)
Contact Configuration:4 Changeover 
Contact Material:Fine Silver Alloy (AgCdO)
Operate Time:< 15 ms
Release Time:< 10 ms

3-Input Auctioneer

Input Channels:3 (isolated)
Input Signal:4-20 mA DC
Input Impedance:250 Ω 
Output Signal:4-20 mA DC 
Output Load:0–850 Ω
Power Supply:24V DC
Power Consumption:< 3W

3-Input Auctioneer

Input Channels:3 
Input Signal:4-20 mA DC
Input Impedance:250 Ω
Output Signal:4-20 mA DC
Output Load:0–750 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 2.8W

Square Root Extractor

Input Signal:4-20 mA DC 
Input Impedance:250 Ω
Output Signal:4-20 mA DC 
Output Load:0–850 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 1.8W

Rate Limted Follower

Input Signal:4-20 mA DC 
Input Impedance:250 Ω 
Output Signal:4-20 mA DC 
Output Load:0–850 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 2.0W

Derivative

Input Signal:4-20 mA DC
Input Impedance:250 Ω
Output Signal:4-20 mA DC 
Output Load:0–850 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 1.8W

Multiplier Error

Input Channels:3 (X, Y, Reference)
Input Signal:4-20 mA DC 
Input Impedance:250 Ω 
Output Signal:4-20 mA DC (Error = (X*Y) - Reference)
Output Load:0–850 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 2.5W

D.C Signal Generator

Current Output:0-20 mA, 4-20 mA
Voltage Output:0-10V, ±10V
Output Resolution:16-bit 
Current Accuracy:±0.05% of reading 
Output Load Current: 0–850 Ω
Power Supply:100-240V AC

Summer Bias Inverter

Input Channels:2 or 3
Input Signal:4-20 mA DC
Input Impedance:250 Ω
Output Signal:4-20 mA DC 
Output Load:0–850 Ω
Power Supply:24V DC (±10%)
Power Consumption:< 2.2W

Termination Unit

Wire Size (Field Side):0.5 - 2.5 mm² 
Contact Resistance:< 2 mΩ
Dielectric Strength:> 2.5 kV
Insulation Resistance :> 100 MΩ
Current Rating:10-12 A per terminal
Voltage Rating:300-400 V

FIP Interface

Supply Voltage:+5V DC
Power Consumption:500 mA 
Isolation:1500 V AC
FIPIO Port:9-pin D-sub
Data Rate:31.25 kbit/s (Fixed)
Bus Topology:Bus with trunk and drops

Analog Output Module

Analog Output 
Output Channels:16
Output Signal:4-20 mA 
Resolution:16-bit
Accuracy:±0.05% of span 
Load Impedance:≤ 850 Ω (at 20 mA)
Max Output Compliance:20 V

MCS Graphic Card Elographics

E27160MKIIA
CONTROL BOARD
Supply Voltage:+5 VDC and +24 VDC
Power Consumption:5 W (typical)
Microprocessor:16-bit or 32-bit 
Serial Communication:RS-232

Touchscreen Control Module

TOUCHSCREEN CONTROL MODULE 
FOR 90 SYSTEM IOS
Supply Voltage:Typically +24 V DC
Power Consumption:5 - 10 W
Screen Size:5.7 inches
Resolution:320 x 240 pixels

17" Color Monitor V80

E20FFA-BC1
17-inch Industrial Color Monitor
Supply Voltage:24 V DC
Power Consumption:35 W
Input Signals:VGA (D-Sub 15)
Screen Size:17 inches
Aspect Ratio:5:4 or 4:3

16" Industrial Color Monitor

INTECOLOR E01942-20F 
COLOR MONITOR
Supply Voltage:24 V DC (±10%)
Power Consumption:30 W
Input Signals:VGA (D-Sub 15-pin)
Screen Size:16 inches (diagonal)
Native Resolution:1280x1024 (SXGA)
Aspect Ratio:5:4
Panel Technology:TFT LCD

16" Industrial Color Monitor

INTECOLOR E01941-20F 
COLOR MONITOR
Power Supply:24 V DC (±10%)
Power Consumption:35 W (typical), <1 W (standby)
Input Voltage Range:20-30 V DC
Video Inputs:VGA (D-Sub 15-pin), DVI-D
Communication:USB for touch interface (if equipped)
Inrush Current:<20 A (at 24 V DC)

Digital Slave Input Module

DSI01
Digital Slave Input Module
Input Channels:16 points
Input Voltage:24 V DC (nominal)
Operating Range:19.2-30 V DC
ON Voltage:≥15 V DC
OFF Voltage:≤5 V DC
Input Current:≤3 mA per point (typical)
Input Impedance:7 kΩ