ABB Drives

POWER INTERFACE BOARD

Compatibility: DCS800 series drives
Operating Temperature: 
Typically -10°C to +55°C (14°F to 131°F)
Humidity: humidity up to 95%

POWER INTERFACE BOARD

Compatibility: DCS800 series drives
Operating Temperature: 
Typically -10°C to +55°C (14°F to 131°F)
Humidity: humidity up to 95%

COMMUNICATION BOARD

Series: SDCS
Operating Voltage: Typically 24V DC 
Power Consumption:  5-10 W
Current Consumption: 200-400 mA 
Operating Temperature Range: -20°C to 70°C (-4°F to 158°F)
Storage Temperature Range: -40°C to 85°C (-40°F to 185°F)

Ethernet Adapter module

Estimated min. lifetime: 100 000 h
All materials UL/CSA-approved
Maximum Segment Length: 
100 m / 328 ft
Topology: Star
Serial Communication Type: 
Half or Full Duplex
Transfer Rate: 10Mbps or 100Mbps

FlashDrop

PC cable
Battery charger
Battery charger (AC power) cable 
with a set of plugs
User Manual
DrivePM CD

INTERFACE BOARD

Input Voltage: 5 VDC (typical)
Power Consumption: ≤ 2 W
Signal Type: Digital and analog signal transmission
Operating Temperature: -20°C to +70°C (-4°F to +158°F)
Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Humidity: 5% to 95% non-condensing

Excitation module

Type: DCS400 Excitation Module
Input Voltage: AC 85 - 264 V
Output Voltage: DC 0 - 250 V
Output Current: Maximum 30 A
Frequency Range: 50/60 Hz
Operating Temperature: -20°C to +60°C

I/O Board

Input Voltage Range: 24 V DC 
Current Consumption: 
Depends on the configuration of the I/O channels
Signal Type: Digital
Input Type: 24 V DC 
Output Type: Relay contacts or transistor outputs
Relay Output Rating:  30 V DC / 2 A per relay

Interface Board

Low power design
typically <10 W
Multiple I/O ports for 
interfacing with sensors
actuators, and controllers
Optimized for high-speed 

Interface Board

24 VDC
Low power design
typically <10 W
Multiple I/O ports for 
interfacing with sensors
actuators, and controllers.
Optimized for high-speed 
communication to minimize latency

Circuit Board

Voltage: 24V DC
Current: Varies based on the specific application
Number of Inputs: 16
Number of Outputs: 16
Input Voltage: 24 VDC
Output Voltage: 24 VDC
Operating Temperature: -20°C to 60°C (-4°F to 140°F)

CONTROL CARD

Main control board 
16 Ch. 218/48
I/O Module
24-250 VAC/DC relays

Drive Control Unit

DRIVE CONTROL UNIT
COATED
BLANK
24 VDC
(64607901)

Fiber Optic Repeater Module

RFO810
Up to 3 km
Supports HN800 or CW800 bus interfaces
Requires use of HBX01L/HBX01R for bus terminations
24V DC
20°C to +60°C

ACS800 R2 to R6 STO Frequency Converter

Safety Category:Category 3 (EN 954-1) 
Response Time:≤ 20 ms
Supply Voltage:24 V DC ±10%
Power Consumption:≤ 2 W
Input Signal:24 V DC (Pulse test: 0.5 Hz, 1 ms)
Input Current:6 mA per channel
Isolation Reinforced isolation : 500 V AC

Inverter Filter Plate

Rated Voltage:380–480 V AC, 3-phase (±10%)
Rated Current:100 A (at 40°C ambient)
Frequency:50/60 Hz
Leakage Current:< 5 mA (at 480 V AC)
Insulation Resistance:> 100 MΩ (500 V DC)
Dielectric Strength:3000 V AC

CONVERTER POWER BOARD

3-phase AC: 380–480 V AC
DC Bus Voltage:520–720 V DC
Power Rating:Typically 1–50 kW
Operating Temperature:-10°C to +50°C
Storage Temperature:-40°C to +85°C

CANopen Adapter Module

Product Type:CANopen Slave Interface Module
Catalog Number:160-NCAN-02C
Compatible Networks:CANopen
Power Supply:24V DC (±10%), 120 mA typical
Terminals:5-pin removable screw terminal

Circuit Board

Voltage: 24V DC
Input Impedance: 3 kΩ
Current: 0–20 mA, 4–20 mA
Resolution: 12-bit
Isolation Voltage: 2 kV AC
Altitude: ≤ 2000 m

AC drive

Output Current: 105 A
Integrated Filter: L500 
Frame Size: R7
Cooling Method: Air cooling 
Voltage:3-phase 380–480 V AC (±10%)
Frequency:47–63 Hz
 Input Current:120 A
Motor Power Range:55–75 kW 
 Apparent Power (S1):89 kVA (at 480 V)

Main Circuit Interface Card

System Voltage:24 V DC (19.2–30 V DC)
Power Consumption:≤ 1.5 W (typical)
Communication Protocol:Profibus DP-V1
Modbus RTU (via FCI module)
Isolation:Galvanic isolation between 

I/O Module Adaptor

Data Transfer Rate:Up to 12 Mbps (PROFIBUS)
Isolation Voltage:1.5 kV AC
Power Supply:24 V DC
Power Consumption:≤ 1.2 W

Drive Unit Drive Controller

Control Platform:32-bit RISC processor with FPGA logic
Control Methods:DTC , Scalar, Vector
I/O Capacity:16x DI
Operating Voltage:24 V DC (±10%)
Power Consumption:25 W (typical)
Memory:2 GB Flash (firmware/logs)
    

Controller Module

Model: KUC755AE117 / 3BHB005243R0117
Product Type: Controller Module
Power Supply Voltage: 24V DC 
Operating Temperature: 0°C to +55°C
Storage Temperature: -20°C to +70°C
Humidity: Relative humidity 5% -95%

High voltage inverter board

Rated System Voltage:3300V AC (2.3–4.16 kV range)
DC Link Voltage:5600V DC (max)
IGCT Control :24x Gate driver channels 
Gate Drive Voltage:+20V / -5V
Auxiliary Power:24V DC (±10%), 150W
Isolation Voltage:6 kV AC 
Response Time:<2 µs