ABB

IGBT Module

Collector-Emitter Voltage (Vces):1200V
Collector Current (Ic @ 25°C):450A
Collector Current (Ic @ 80°C):300A
Pulse Current (Icm):900A
Power Dissipation (Ptot):1800W
Gate-Emitter Voltage (Vges):±20V
Turn-on Delay Time (tdon):110ns
Rise Time (tr):50ns
Turn-off Delay Time (tdoff):400ns
Fall Time (tf):120ns
Switching Frequency:Up to 20kHz

Bus Coupler

Supply Voltage: 24V DC (19.2-30V DC)
Power Consumption: 1.5W 
Current Capacity: 6A 
Isolation Voltage: 500V AC 
Fieldbus Protocol:PROFIBUS DP-V1
Data Rate:Up to 12 Mbps
Address Range:1-125 (PROFIBUS)
I/O Connection:S800 I/O bus

TEMP MEASURING BOARD

Input Channels:4 or 8 (isolated)
Supported Sensors:PT100/PT1000, TC (J/K/T/E), 0-20mA, ±10V
Measurement Accuracy:±0.1% FS (RTD), ±1°C (TC)
Resolution:0.01°C (RTD), 0.1°C (TC)
Update Rate:100ms per channel
Isolation:1500V AC 
Power Supply: 24V DC (±10%) via backplane
Power Consumption: <3W
Input Impedance: >1MΩ 
Max. Input Voltage: ±15V

Gate Circuit Board

DRIVE
IGBT
BOARD KIT
Modbus TCP/IP
-20°C to 60°C (-4°F to 140°F)
Number of Inputs: 16
Number of Outputs: 16

07KT98 Advant Controller 31 Basic Unit

Microprocessor-based protection
Three-phase trip-free mechanism
Front-connected auxiliary contacts
Integrated earth fault protection
Remote control and monitoring capabilities
High-performance AC800F platform
Supports a wide range of I/O modules
Supports a variety of programming languages
Suitable for a wide range of industrial applications
Compact and modular design

Frequency Converter Driver Board

Voltage Input: 380V to 690V AC (3-phase) 
Switching Frequency: 2–16 kHz range
Operating Temperature: -10°C to +50°C (ambient, typical)
Humidity: ≤95% non-condensing

Power Supply

Input Voltage Range: 85-264V AC (universal input)
Input Frequency: 47-63Hz
Inrush Current: <25A (at 115V AC), <50A (at 230V AC)
Power Factor: >0.95 (at full load)
Efficiency: 92% typical
Output Voltage: 24V DC
Output Current: 6A continuous
Current Limit: 7.5A 
Ripple & Noise: <150mV p-p 
Load Regulation: ±0.5% (10-100% load)
Line Regulation: ±0.2% (85-264V AC)

BRC400 Bridge Controller

CONTROLLER
HARMONY BRIDGE
BRC400
BUTTON CELL BATTERY
SINGLE PORT
RELAY OUTPUT

Servo Control Board

Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs

PC BOARD

JINTC1C
PC BOARD
PCB FOR ACS850-04-035A-5+E200+J400
ACS880 SERIES

DC drive motherboard

Memory:32MB SDRAM
Control Loop Time:100μs (speed)
Digital I/O:12x 24V DC inputs
Supply Voltage:24V DC ±10%
Power Consumption:15W max
Isolation :2500V AC 

Control Board

Clock Speed:150MHz (DSP), 100MHz (FPGA)
Memory:512kB Flash, 68kB SRAM
Operating Voltage:24V DC ±10%
Power Consumption:12W typical
Isolation:2500V AC
Control Loop Update: 62.5μs (speed)
Analog Inputs:2 ch (16-bit, ±10V/4-20mA)
Digital Inputs:6 ch (24V DC, 3ms filter)
Relay Outputs:3 ch (250V AC/5A)
PTC Input:2 ch (Motor temp sensors)

POWER SUPPLY CARD

Input Voltage Range: 85–264 VAC
Input Frequency: 47–63 Hz
Input Current: 3.5 A max @ 120 VAC, 1.8 A max @ 240 VAC
Inrush Current: 30 A (typical, cold start)
Power Factor: >0.95 (at full load)
Output Voltage: 24 VDC (±1%)

Digital Output Module

Relay Version: 5–250 VAC/VD
Solid-State Version: 24 VDC
Switching Frequency Relay: ≤5 Hz
Solid-State: ≤100 Hz
Channel-to-Channel: 500 VAC
Channel-to-Backplane: 1500 VAC

Main Control Circuit Board

PROFIBUS DP
PROFINET
Modbus RTU/TCP
Ethernet/IP
Clock Speed: ≥200 MHz 
Supply Voltage: 24 VDC (±10%)
Power Consumption: Typically <15W

Communication Module

PROFIBUS: 9.6 kbps to 12 Mbps
Modbus TCP: 10/100 Mbps
PROFIBUS: 9-pin D-sub
Ethernet: RJ45
Terminal blocks for serial communication
PROFIBUS: Up to 124 slaves
Modbus: 247 RTU devices 
Isolation: 1500 VAC 

Interface Board

Number of channels: 16 (configurable)
Voltage range: 24 VDC (18-30V)
Input impedance: 3kΩ
Isolation: 500V channel-to-channel
Switching capacity: 0.5A @ 24VDC
Supply Voltage: 24 VDC (±10%)
Power Consumption: <3W typical

Robot Drive Unit

Input Voltage:3-phase 200-480VAC (±10%)
DC Bus Voltage: 600VDC nominal
Power Rating: 7.5kW (varies by configuration)
Peak Current: 25A (3 sec)
Continuous Current: 12A
PWM Frequency: 8kHz
Control Cycle Time: 0.5ms
Overload Capacity: 200% for 3 seconds

Control Board

Main Processor: 32-bit DSP + FPGA
Clock Speed: ≥300 MHz
Memory Flash: 128MB 
Control Cycle Time: <100μs
Digital Inputs: 8 channels (24VDC)
Digital Outputs: 4 channels (relay)
Analog Inputs: 2 channels (±10V/4-20mA)
Analog Outputs: 2 channels (0-10V/4-20mA)

DriveBus Interface Module

Data rate: 10 Mbps
Max. distance: 100m (fiber length)
ModuleBus connection to AC 800M
Supply voltage: 24 VDC (±10%)
Power consumption: <5 W
Isolation: 1500 VAC 
Supports up to 12 drives per module

Optical Module

Operating Voltage: 24 Vdc (±10%).
Data Rate: 100 Mbps
Operating Temperature: -40°C to +70°C
Humidity: 5–95% non-condensing

Control Module

Clock Speed: 500-800 MHz
RAM: 256MB-512MB DDR
Flash Storage: 512MB-1GB
Digital Inputs: 16-32 channels 
Analog Inputs: 8-16 channels
2x Ethernet (10/100/1000 Mbps)
1x RS-232/485 (configurable)
1x USB (Type A, for maintenance)

Speed Module

Power Supply:24V DC (±10%)
Tachometer input: 0-10V DC or 4-20mA
Pulse input: Up to 100kHz frequency
Analog output: ±10V DC or 4-20mA
Relay outputs: 2x SPDT (5A @ 250V AC)
Speed Range: 0-10,000 RPM (configurable)
Resolution: 0.1% of full scale or better
Digital outputs: 24V DC, 0.5A

Analog output module

Voltage: 0-10V DC, ±10V DC
Current: 4-20mA, 0-20mA 
Load Capacity:Voltage: ≥1kΩ
Isolation:1500V AC channel-to-channel
Backplane Power: 5V DC @ 500mA (typical)
Field Power: 24V DC (±10%) for outputs
Power Consumption: 6W (typical)

High Voltage Inverter Board

Voltage Rating: 1200V–1700V
Input Voltage (DC Link): 300–1000V DC
Output Voltage (AC): 3-phase, 0–480V AC
Current Rating: Up to 500A 
Switching Frequency: 2–20 kHz