















TERMINATION RESISTOR MODULE
LINKNET
Link Termination Resistor
TERMINATION RESISTOR MODULE
SCREW CLAMP TERMINALS
Linknet 6-Channel Analog Input Module
Display Type: 2 line x 24 characters
Accuracy: 1 % at 25 °C
Power Supply Input: (18 to 32) V (dc)
Network to I/O channel: 277 V (ac)
Power supply input to network: 277 V (ac)
Power supply input to I/O channel: 500 V
Humidity Standards: 20 and 55 °C at 95% for 48hrs
Input Voltage: +24 Vdc at 1 A
Keypad/Display: 30 Multi-function Keypad
Temperature Range: (–40 to +55) °C
Output module
Brand:GE Fanuc
Series:RX3i PacSystem
Part Number:IC694MDL742
Type:Output module
Rated Voltage:12/24V DC
Isolation:250V AC continuous;
Electronic Short-Circuit Protection (ESCP):Yes
LEDs:Yes
Hot Insertion and Removal:Yes
Discrete Output Module
Series:Versamax
Part Number:IC200MDL740
Number of Points:16 Outputs
Number of groups:1
Group to Group Isolation:None
Point to Point Isolation:None
Fuse:None
RX3i PACSystem option Module
Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CHS016
Product Description:Universal backplane
Grounding bar:Integrated
Module Hot-swap:Supported
Lifecycle status:Active
Mounting:Rack
No of slots:Sixteen (16)
Type:Universal backplane
Number of Slots:16
Input:+24 Volts
Recommended wire size:14 to 22 AWG
Enclosure:IP54 or greater
CPU MODULE
Series:RX3i PacSystem
Part Number:IC695CPE305
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Communication:RS-232
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Maximum Block Size:128 kilobytes
I/O pack
CARD
INPUT/OUTPUT PACK
PROTECTION TYPE
FOR MARK VIE TURBINE CONTROL SYSTEM
2 ETHERNET PORTS
POWER SUPPLY
LOCAL PROCESSOR
DATA ACQUISITION BOARD
Communications Module
UR7HH
DISCONTINUED BY MANUFACTURER
INTER-RELAY COMMUNICATIONS MODULE
HORIZONTAL UNIT
820 NM
MULTI MODE
LED
2 CHANNELS
Embedded Controller Module
Software: ControlST V04.03.18C
Relative humidity: 5% to 95%, no-condensing
Power Requirements +32 V dc to 18 V dc
Microprocessor: Freescale Power PC
(Power QUICC II PRO 667 MHz)
Memory: 256 MB DDR SDRAM
I/O carrier barrier style
Brand:GE Fanuc
Series:Versamax
Part Number:IC200CHS001
Product Type:Barrier-style I/O carrier
Barrier-Style Terminals:36
Carrier Mounting:DIN rail
Max. I/O Points:32
Current per Point:Max 2 Amps
Analog input module
Manufacturer:GE Fanuc
Series:Versamax
Part Number:IC200ALG240
Product Type:Analog Input Module
Number of Inputs:8
Intelligent Module:Yes
Input Data:16-Bit Input Data
Operating Modes:Current Mode or Voltage Mode
Current Range:1 to 20 milliamps
Voltage Range:-10 to 10 Volts DC
INTERFACE MODULE
Brand:GE Fanuc
Series:Versamax
Part Number:IC200PBI001
I/O Modules:64
Network Address:1-125
User Diagnostics Data:5 bytes
Connector:9 Pin D-sub
CONTROLLER APPLICATION BOARD
531X139APMARM7
DISCONTINUED BY MANUFACTURER
PC APPLICATION BOARD
CPU MODULE
Manufacturer:GE Fanuc
Series:RX3i PACSystem
Part Number:IC698CRE030
Product Type:CPU
User Memory:64 MB
CPU:Redundancy CPU

Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.