ALL MANUFACTURERS

Pcb board

1 PORT CHANNEL
Operating Temperature Range: -40°C to +70°C. 
Power Consumption: Maximum of 5W
Data Transfer Rate: Up to 400 Mbps
Digital I/O Channels: Provides 32 digital

PROFIBUS INTERFACE CARD

PROFIBUS INTERFACE CARD
1 PORT CHANNEL
Operating Temperature Range: -40°C to +70°C. 
Power Consumption: Maximum of 5W
Data Transfer Rate: Up to 400 Mbps
Digital I/O Channels: Provides 32 digital

I/O Modnet 1/D

CBK 132.1 029.210 
753 Serial 
I/O Modnet 1/D

32bit-contr，W，|/O peri

CCU 132.08 590.037498 
32bit-contr，W，|/O peri

Current Input Module

Number of input channels 
16-channel input, isolated
Input signal 4 to 20 mA
Allowable input current 24 mA 
Accuracy ±0.1% of full scale
Data refresh cycle 10 ms
Transmitter power supply 24.0 to 25.5 V 
Temperature drift Max. ±0.01%/°C

Current Input Module

Number of I/O channels 
8-channel input, isolated channels 
I/O signal 4 to 20 mA 
Allowable input current 25 mA 
Accuracy ±16 µA 
Data update period 10 ms 
Temperature drift ±16 µA/10 °C
Maximum currentconsumption 
360 mA (5 V DC), 450 mA (24 V DC)

ELECTRONIC MODULE

SIMATIC DP
ELECTRONIC MODULE 
ET200S: 2AI HIGH SPEED I2WIRE
0 - 20MA, 4 - 20MA, 15BIT
15 MM WIDTH,FOR 2-WIRE 
TRANSDUCER,CYCLE TIME OF 
THE MOD.: 0.1MS,
WITH LED SF (GROUP FAULT)

Isolation Module 4-Port Benefits

High-Speed 1 MS/s 16-bit Isolation Module 
(4 ch) High Noise Immunity  
Suitable for testing and long-term monitoring 
for power generators and multi-output power supplies. 
Provides dynamic analysis of multi-channel 
data recording applications.
Applicable to DL350 and DL850 series

Vertical 12 volt 5 amp Battery Charger

FREQUENCY RANGE:45 Hz to 65 Hz
VOLTAGE RANGE:90 V to 305 V (L-N)
DC OUTPUT:5 A DC 12 V DC
RIPPLE AND NOISE:<1%
EFFICIENCY:>80%
LINE:<0.001% Vo
LOAD:1% Vo

Vertical 24 volt 5 amp Battery Charger

FREQUENCY RANGE:45 Hz to 65 Hz
VOLTAGE RANGE:90 V to 305 V (L-N)
DC OUTPUT:5 A DC 24 V DC
RIPPLE AND NOISE:<1%
EFFICIENCY:>80%

24 Volt 5 Amp Compact Battery Charger

VOLTAGE RANGE:90 V to 305 V (L-N)
DC OUTPUT:5 A DC 24 V DC at 13.7 V DC
RIPPLE AND NOISE:<1%
EFFICIENCY:>80%
REGULATION LINE：<0.001% Vo
LOAD：1% Vo

12 volt 5 amp Compact Battery Charger

AC SUPPLY VOLTAGE RANGE
90 V to 250 V (L-N)
DC OUTPUT
5 A DC 12 V DC at 13.7 V DC
RIPPLE AND NOISE:<1%
EFFICIENCY:>80%
REGULATION LINE:<0.001% Vo
LOAD:1% Vo

Auto Transfer Switch & Mains Control Module

CONTINUOUS VOLTAGE RATING
8 V to 35 V continuous
CRANKING DROPOUTS
Able to survive 0 V for 50 mS, 
providing supply was at least 10 V 
before dropout and supply recovers to 5 V. 
This is achieved without the need for internal batteries
MAXIMUM OPERATING CURRENT
460 mA at 12 V, 245 mA at 24 V
MAXIMUM STANDBY CURRENT
375 mA at 12 V, 200 mA at 24 V
CHARGE FAIL/EXCITATION RANGE
0 V to 35 V

Failure Load Share Control Modulee

CONTINUOUS VOLTAGE RATING
5 V to 35 V continuous
CRANKING DROPOUTS
Able to survive 0 V for 100 mS, 
providing supply was at least 10 V 
before dropout and supply recovers to 5 V. 
This is achieved without the need for internal batteries
MAXIMUM OPERATING CURRENT
530 mA at 12 V, 280 mA at 24 V
MAXIMUM STANDBY CURRENT
320 mA at 12 V, 160 mA at 24 V
CHARGE FAIL/EXCITATION RANGE
0 V to 35 V

Synchronising & Load Sharing Auto Start Control Module

CONTINUOUS VOLTAGE RATING
8 V to 35 V continuous
CRANKING DROPOUTS
Able to survive 0 V for 50 mS, 
providing supply was at least 10 V 
before dropout and supply recovers to 5 V.
This is achieved without the need for internal batteries
MAXIMUM OPERATING CURRENT
460 mA at 12 V, 245 mA at 24 V
MAXIMUM STANDBY CURRENT
375 mA at 12 V, 200 mA at 24 V
CHARGE FAIL/EXCITATION RANGE
0 V to 35 V

Auto Mains (Utility) Failure Control Module

CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
Able to survive 0 V for 50 mS
providing supply was at least 10 V 
before dropout and supply recovers to 5 V
This is achieved without the need for internal batteries
LEDs and backlight will not be maintained during cranking
MAXIMUM OPERATING CURRENT
85 mA at 12 V, 96 mA at 24 V
MAXIMUM STANDBY CURRENT
51 mA at 12 V, 47 mA at 24 V

Auto Mains (Utility) Failure Control Module

Able to survive 0 V for 50 mS
providing supply was at least 10 V 
efore dropout and supply recovers to 5 V
This is achieved without the need for internal batteries. 
LEDs and backlight will not be maintained during cranking
CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
MAXIMUM OPERATING CURRENT
85 mA at 12 V, 96 mA at 24 V
MAXIMUM STANDBY CURRENT
51 mA at 12 V, 47 mA at 24 V
MAXIMUM SLEEP CURRENT
35 mA at 12 V, 32 mA at 24 V
MAXIMUM DEEP SLEEP CURRENT
<10 uA at 12 V, <10 uA at 24 V

Auto Mains (Utility) Failure Control Module

CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
5 V for up to 1 Minute
CRANKING DROPOUTS
Able to survive 0 V for 100 mS, 
providing supply was at least 10 V 
before dropout and supply recovers to 5 V. 
This is achieved without the need for internal batteries
MAXIMUM OPERATING CURRENT
510 mA at 12 V, 240 mA at 24 V
MAXIMUM STANDBY CURRENT
330 mA at 12 V, 160 mA at 24 V
CHARGE FAIL/EXCITATION RANGE
0 V to 35 V

Auto Mains (Utility) Failure Control Module

CONTINUOUS VOLTAGE RATING
8 V to 35 V Continuous
5 V for up to 1 minute
MAXIMUM OPERATING CURRENT
510 mA at 12 V, 240 mA at 24 V
MAXIMUM STANDBY CURRENT
330 mA at 12 V, 160 mA at 24 V
CHARGE FAIL/EXCITATION RANGE
0 V to 35 V

Auto Mains (Utility) Failure Control Module

Operating Voltage Range: 8 V to 35 V
Cranking Dropout: 
Able to withstand 0 V for 50 ms, 
provided the supply was at least 10 V 
before the dropout and recovers to 5 V 
afterward. No internal battery is required.
Maximum Operating Current: 
100 mA at 12 V, 105 mA at 24 V
Maximum Standby Current: 
60 mA at 12 V, 55 mA at 24 V
Maximum Sleep Current: 
40 mA at 12 V, 35 mA at 24 V

Generator Control Module

Back-lit icon LCD display
Front panel editing
LED and LCD alarm indication
Power Save mode
CAN and Magnetic Pick-up/Alt.
versions available (specify on
ordering)
PC configurable
6 Digital inputs
4 Outputs (2 configurable on
Magnetic Pick up/Alt., 4 configurable on CAN version)
Configurable timers and alarms
Alternative configuration
Remote Start input
Generator voltage display

ELECTRONIC MODULE

SIMATIC DP
ELECTRONIC MODULE FOR ET 200S
2 AI STAND.I-2DMU 15 MM WIDE
4 .. 20MA; 13 BIT FOR 
2-WIRETRANSDUCER CYCLE 
TIME 65 MS/CHANNEL WITH LED SF

POWER MODULE

SIMODRIVE 611 
POWER MODULE
2 AXES, 50A
INTERNAL HEAT DISSIPATION
RATED MOTOR CURRENTS: 
FEED = 18 A MAIN 
SPINDEL = 24 A

Swappable lens with C-mount connection

suitability for use Swappable lens with C-mount connection
suitability for operation lens for MV440
mechanical datacolor black
design, dimensions and weight
sheight 37.2 mm
diameter 29.5 mm

Kinetix 300 Servo Drive

120 Volts Doubler Mode:Yes
Continuous Output Current (0-peak):5.7 Amperes
Integrated AC (EMC) Line Filter:No
Input Voltage:120/240 Volts (AC), 1 Phase
Power Rating:800 W
Part Number/Catalog No.:2097-V31PR2-LM
Safe Torque-Off:Yes