
Carel Fan Speed Controller
Single-phase supply 230V +10%/-1
Frequency 50/60
Control signal 0 to 10V
Power supply for possible manual control (+V terminal) 20 Vdc 40
Input Voltage:230 VAC ± 10%, 50/60 Hz
Operating Temperature:0°C to +50°C
Storage Temperature: -20°C to +70°C
Relative Humidity:10% to 90% RH, non-condensing.
Analog I/O Module
Power Supply Voltage:24 VDC
Analog Input Channel :4 channels per module
Analog Input Range: ±10V
Digital Data Range :±2000
Resolution :12 bits (1LSB=5 mV)
Input Impedance :200 KΩ and above
Response Time: 3 ms × channels
Absolution Input Range :±15 V
Analog Output Range: 0~10V
Digital Data Range :0~4000
CYLINDRICAL PHOTOELECTRIC SENSORS
Housing design (light emission) Cylindrical
Housing length 70.2 mm
Thread diameter (housing) M18 x 1
Optical axis Axial
Sensing range max. 0.05 m ... 7 m
Sensing range 0.05 m ... 6 m
Type of light Visible red light
Light source LED
Adjustment Potentiometer, 270
Eddy Current Displacement Sensor
Operating temperature range: 0...+ 100°C
Operating frequency range: 0...15 kHz (-3dB)
Displacement measuring range: 2,15 mm
Sensitivity: 7,87 V/mm (200 mV/mil)
Mean voltage: -10,00 V
Power supply: -24 V nominal
Standard cable: 4 - core (4 x 0,2 mm2)
CONNECTING CABLE
Connecting cable
shielded for SIMATIC S7-300/1500
between front connectormodule and
Connection module 16x0.14mm
2 with IDC connectors, L = 1.0 m
PCB CARD
Operating Voltage:120/230 V AC
Current Rating :16 A
Power Output :1.6 kW
Communication Interface:Profibus DP
Control Signals:Up to 16 digital inputs and outputs
Temperature Range:-25°C to 55°C
Analog I/O module
SIMATIC S7-1500
Analog I/O modules
Fully modular connection
Connection module
at DC / rated value 24 V
rated value 50 V
at DC / maximum 50 V
current / rated value 1 A
during operation 0 ... 60 °C
during storage -40 ... +70 °C
SIMATIC S7-1500
mounting rail 245 mm (approx. 9.6 inch)
incl. grounding screw
integrated DIN rail for mounting of
incidentals such as terminals
automatic circuit breakers and relays
CPU MODULE
SIMATIC S7-1500
CPU 1511-1 PN
central processing unit with work
memory 300 KB for program
and 1.5 MB for data, 1st interface
PROFINET IRT with 2-port switch
25 ns bit performance
SIMATIC Memory Card
SIMATIC S7-200 SMART
CPU ST30, Standard CPU
DC/DC/DC,onboard
I/O: 18 DI 24 V DC; 12 DO 24 V DC
Power supply: DC20.4-28.8V DC
Program/data memory 30 KB
Digital output module
Product type designation DQ 8x24VDC/2A HF
HW functional status FS03
Firmware version V2.2.0
Rated value (DC) 24 V
permissible range, lower limit (DC) 19.2 V
permissible range, upper limit (DC) 28.8 V
Current consumption, max. 40 mA
Rated value (DC) 24 V
Power available from the backplane bus 0.9 W
Analog input module
SIMATIC S7-1500 Analog input module
AI 8xU/I/R/RTD BA
16 bit resolution,Accuracy 0.5%, 8 channels in groups of 8
Common mode voltage 4 V DC,Diagnostics
Hardware interrupts; Delivery including infeed element
shield bracketand shield terminal
Front connector (screw terminals or push-in)
to be orderedseparately
Accessories
Headers & Wire Housings
NANO-FIT TPA V0 BLK 3 CKT
Product:Accessories
Number of Positions:3 Position
Pitch:2.5 mm (0.098 in)
Tradename:Nano-Fit
Minimum Operating Temperature:- 40 C
Maximum Operating Temperature: + 115 C
Ethernet Switch
Switching Capacity: 32 Gbps
Forwarding Rate: 23.8 Mpps
MAC Address Table: 8K entries
Jumbo Frame Support: Yes (up to 9KB)
VLAN: Supports up to 256 VLANs
Power Supply Voltage: 12-48 VDC
Power Consumption: 20 W (typical)
Operating Temperature:-40°C to +75°C (-40°F to +167°F)
Storage Temperature:-40°C to +85°C (-40°F to +185°F)
Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.