ALL MANUFACTURERS

Control board

Voltage: 48-250V DC
Frequency: 50/60Hz (±10%)
Power Consumption: 15W typical
Memory: 256MB Flash
Sampling Rate: 4kHz
Binary Inputs: 16 
Binary Outputs: 8 

Communication adapter

Ethernet connector
Fibre optic SPA-bus connectors
Auxiliary power supply connector
SPA TX and RX LEDs
LAN and diagnostic LEDs

Ethernet Adapter

Ethernet connector
LON/SPA bus FO connector (optional)
LON/SPA Rx LED4. LON/LAN service pin
LAN and diagnostic LEDs

Servo Drive

Input Voltage:3-phase 200-480V AC (±10%)
Frequency:50/60Hz (±5%)
Power Range:3.0kW 
Peak Current :18A 
Output Current:6A RMS
Switching Frequency:8kHz (PWM)

Power Supply Unit

DC Output Voltage:24V DC (±1%)
Output Current:40A (continuous)
Power Rating:960W (max)
Efficiency:>90% (at full load)
Input Voltage:3-phase 200-480V AC (±10%)
Frequency:50/60Hz (±5%)
Input Current :10A (max @ 400V AC)
Inrush Current:30A (peak, for 10ms)

Main computer assembly

RAM:4GB DDR3
Storage:32GB SSD 
Input Voltage:24V DC (±10%)
Power Consumption:50W (typical)
Ethernet:10/100/1000 Mbps

Drive board

Input Voltage: 24 VDC (±10%)
Analog Inputs: 0–10 VDC or 4–20 mA
Operating Temperature: -25°C to +55°C (-13°F to +131°F).
Humidity: Up to 95% non-condensing.
Vibration Resistance: 5–150 Hz

Circuit Board

Power Supply: Typically 24 V DC
Input Voltage Range: typically 0-10V DC 
Operating Temperature Range: 
Typically -20°C to 70°C (-4°F to 158°F)
Storage Temperature Range: 
Typically -40°C to 85°C (-40°F to 185°F)
Humidity:  5% to 95%, non-condensing

F-series Extension Adapter

Voltage: 24V DC (±10%)
Consumption: 2.5W typical
Isolation: 1.5kV AC 
PROFIBUS DP (up to 12Mbps)
Modbus RTU (RS485)
CANopen (optional)

Frequency Converter

Frequency (f):47.5 ... 63 Hz
Frame Size:R3
Input Voltage (Uin):380 … 480 V
Mounting Type:Wall-mounted_NO UNIT$
Output Current, Normal Use (In):45 A
Output Current, Heavy-Duty Use (IHD):38 A
Output Power, Normal Use (Pn):22 kW
Output Power, Heavy-Duty Use (PHD):18.5 kW

Manual Motor Starter

Setting Range:28 ... 40 A
Rated Operational Current:40 A
Rated Insulation Voltage:690 V
Electrical Durability:25000 cycle
Ampere Rating UL/CSA:40 A
Rated Operational Power AC-3 (Pe) :hree Phase 18.5 kW
Maximum Operating Voltage UL/CSA Main Circuit:600 V AC

Interface board

Voltage: 24V DC
Consumption: 3.5W typical
Isolation: 1.5kV AC
PROFIBUS DP (up to 12Mbps)
Modbus RTU (RS485)
Node Capacity: Up to 124 devices
IEC 60870-5-101/104

Drive Control Uni

Power Supply:24V DC (±10%)
Power Consumption:5W (typical)
Isolation:1.5kV AC
Data Transfer Rate:Up to 12Mbps 
Fieldbus Protocols:PROFIBUS DP
DRIVE-CLiQ:For direct drive connection

Drive Control Unit

Processor: 32-bit dual-core ARM Cortex
Clock Speed: 800MHz
Memory: 512MB Flash
Power Supply:24V DC (±15%)
Power Consumption:8W (typical)
Isolation Voltage:2.5kV AC
I/O Capacity:16 DI/8 DO

Controller Circuit Board

Input Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Isolation: 4kV AC
Processor: 32-bit PowerPC @ 400MHz
Memory:64MB SDRAM

Control I/O Module

Digital Inputs:24V DC
Analog Inputs:0-10V/4-20mA
Input Isolation:2.5kV AC
Backplane Bus:Proprietary high-speed bus
Protocol Support:Modbus RTU, PROFIBUS DP 

Control Circuit Board

Power Supply:24V DC (±10%)
Power Consumption:8W (typical)
Processor:32-bit ARM Cortex-M7 @ 400MHz
Memory:64MB Flash, 32MB RAM
Cycle Time:≤100μs
Digital I/O:24V DC
Analog Inputs:0-10V/4-20mA

System Interconnection Cable

Cable type: 20 × AWG 22 
slot 1 to 18
Outer diameter (nominal): 9.93 mm / 0.39 in
Connector for systeminterconnection cables

CM30 Controller

Output Type:Analogue Relay
Supply Voltage:100 → 240 V ac
Number of Outputs:3
Control Type:ON/OFF
Communication Module Available:Yes
Display Type:LCD, Multi Line, TFT
IP Rating:IP66
Range:ControlMaster CM30
Additional Functionality:ON/OFF
Series:CM30
Panel Depth:121mm
Display Colour:Green, Red, Yellow

Servo Drive

Voltage: 3-phase 200-480V AC (±10%)
Frequency: 50/60Hz (±5%)
Power Range: 2.3kW to 7.5kW
Output Current: 6A to 18A RMS
Control Method: Field-Oriented Control 
Control Bandwidth: 1.5kHz
Speed Range: 0-6000 RPM
Positioning Accuracy: ±1 encoder count

AXIS Drive Unit

Input Voltage:3-phase 200-480V AC (±10%)
Frequency:50/60Hz (±5%)
Power Range:3.0kW 
Peak Current :18A 
Output Current:6A RMS
Switching Frequency:8kHz (PWM)

IGBT module

Collector-Emitter Voltage (Vces): 1700V
Gate-Emitter Voltage (Vges): ±20V
Turn-on Time (ton): 0.5μs (typical)
Turn-off Time (toff): 1.2μs (typical)
Switching Frequency: Up to 20kHz 
Power Dissipation: 1800W (max)
DC Link Voltage: 1000-1200V DC
Typical Applications:400-690V AC drives

Controller with Expanded Memory

Processor:32-bit ARM
Base Memory:512MB DDR4 RAM
Expanded Memory:2GB Flash
Execution Speed:0.05ms/1k instructions
I/O Scan Time:≤1ms (for 1000 I/O points)
Task Capacity:32 concurrent tasks
Digital I/O:Up to 2048 points
Analog I/O:Up to 512 channels
Input Voltage:24V DC (±15%) or 100-240V AC
Power Consumption:15W (typical)

Scanner head

Scanner head,
IR sensor.
3/4in threade
Power Supply: 24V DC (±10%)
Power Consumption: 50W (typical)
Wavelength Range: 900-1100nm
Spot Diameter: 0.2-3.0mm (adjustable)
Focal Length: 150-450mm (motorized adjustment)
Scanning Angle: ±30° (optical)
Positioning Accuracy: ±0.01°