PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
- Home
- ALL MANUFACTURERS
- DEEP SEA ELECTRONICS
- DSE8610MKII 8610-005-02
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
DSE8610MKII 8610-005-02 load sharing controller
Deep Sea Electronics DSE8610MKII 8610-005-02 is a load sharing controller for the DSE8610 MKII generator control systems. It is used to 530 mA at 12 V. Confirm the complete article identity, electrical limits, interfaces, companion hardware and controlled commissioning procedure before ordering.
BEFORE YOU BUY
Confirm the complete load sharing controller
ACTUAL APPLICATIONS
Application context for DSE8610MKII 8610-005-02
Manufacturer documentation places the Load Sharing Controller in practical generator applications. The three cases below describe different operating tasks in which DSE8610MKII 8610-005-02 performs its documented product-family role with the configured companion equipment.
- 01 · ENERGY
Protect renewable-source balancing during renewable-output change
Inside the generator sets, variable renewable sources and bus controls, DSE8610MKII 8610-005-02 operates in its approved product-family role as a Load Sharing Controller. During renewable-output change, the system uses this function to adjust generator contribution as variable supply changes, helping it keep the common bus balanced. - 02 · POWER GENERATION
Sequence mains-failure transfer with Load Sharing
During operation of the mains sensing, standby sets and transfer breakers, DSE8610MKII 8610-005-02 supports the configured automation role as a Load Sharing Controller. During confirmed utility loss, the system uses this function to start the available sets and establish the emergency bus, helping it restore power to the priority bus. - 03 · GENERAL MANUFACTURING
Synchronize production-load sharing with Load Sharing
Inside the parallel sets and high-demand production loads, DSE8610MKII 8610-005-02 operates in its approved product-family role as a Load Sharing Controller. During production peak, the system uses this function to share the electrical demand across the available sets, helping it support production without overloading one set.
Technical specifications for DSE8610MKII 8610-005-02
-
Product ModelDSE8610MKII 8610-005-02
-
Spare ModelDSE8610MKII
-
Product Parametersload sharing controller
-
In stock1 unit
-
Estimated Shipping Size24.8x18.8x5cm
-
ManufacturerDEEP SEA ELECTRONICS
-
Weight0.8 kg
-
Order Code8610-005-02
-
DC Supply8 to 35 V DC
-
Operating Current530 mA at 12 V
-
Standby Current320 mA at 12 V
-
Generator Sensing15 to 415 V phase-neutral
-
Bus Sensing25 to 720 V phase-phase
-
Frequency Range3.5 to 75 Hz
-
CT Inputs4 inputs; 1 A or 5 A
-
Analog Inputs4 configurable inputs
-
Digital Inputs12 negative-switching
-
Magnetic Pickup0.5 to 70 V peak
-
Pickup Frequency1 Hz to 10 kHz
-
Ethernet1 × 10/100 port
-
CAN Interfaces3 isolated CAN ports
-
Front ProtectionIP65 with gasket
View all additional
Alternative Names
DSE8610MKII 8610 005 02
DSE8610 MKII generator control systems load sharing controller
Deep Sea Electronics load sharing controller
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match DSE8610MKII 8610-005-02 to the installed DSE8610 MKII generator control systems
Deep Sea Electronics DSE8610MKII 8610-005-02 is a load sharing controller used in the DSE8610 MKII generator control systems. Use DSE8610MKII 8610-005-02 as the load sharing controller in the DSE8610 MKII generator control systems. Confirm operating current 530 mA at 12 V and the exact installed arrangement before connection.
Record the product label, analog inputs (4 configurable inputs), cable identification, grounding and adjacent hardware before removing the installed unit. Confirm 15 to 415 v phase-neutral, 25 to 720 v phase-phase, the exact mechanical position and the approved system configuration before connection.
After installation, verify can interfaces (3 isolated CAN ports), check diagnostics and test the affected function before returning the equipment to service. Use qualified personnel, keep the applicable manufacturer instructions at the work location and retain the measured results with the equipment service record.
Features:
- Exact identity: DSE8610MKII 8610-005-02
- Product class: load sharing controller
- Family: DSE8610 MKII generator control systems
The Deep Sea Electronics DSE8610MKII 8610-005-02 requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete DSE8610MKII 8610-005-02 identity before exchange
Replace DSE8610MKII 8610-005-02 only after matching the full article identity, load sharing controller, installed 4 inputs; 1 a or 5 a and documented system role. A similar family name or physical outline does not establish interchangeability.
Before removal, photograph the product label, mounting position, 12 negative-switching, cable routing, shields, earth connections and adjacent assemblies. Preserve the approved configuration or parameter backup for recovery.
After installation, restore all controlled settings and complete ip65 with gasket. Review status indications and diagnostics, test the affected function at a safe operating point, and record the final maintenance acceptance evidence.
Features:
- Exact identity: DSE8610MKII 8610-005-02
- Connection: 12 negative-switching
- Test: IP65 with gasket
The Deep Sea Electronics DSE8610MKII 8610-005-02 requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.Features:
- Technical values prepared for DSE8610MKII 8610-005-02
- Installation checks matched to DSE8610 MKII generator control systems
- Exact Deep Sea Electronics identity required before service
Documentation for Deep Sea Electronics DSE8610MKII 8610-005-02 must match the installed equipment and complete product identity; confirm manual applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed sizeConfirm before dispatch
-
Shipping weightConfirm before dispatch
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference8537101190
-
OriginUnited Kingdom
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about DSE8610MKII 8610-005-02
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
Which operating current must engineering verify for DSE8610MKII 8610-005-02?
For DSE8610MKII 8610-005-02, verify the documented operating current is 530 mA at 12 V and confirm the remaining nameplate limits before connection. -
How should maintenance document the analog inputs before removing DSE8610MKII 8610-005-02?
Photograph the analog inputs, which is 4 configurable inputs, plus terminal labels, cable routing, shields and adjacent hardware for DSE8610MKII 8610-005-02. -
What does the dc supply value mean when sourcing DSE8610MKII 8610-005-02?
The exact documented value for DSE8610MKII 8610-005-02 is 8 to 35 V DC; use it with the full article code when checking the supplied configuration. -
Which generator sensing limit applies during commissioning of DSE8610MKII 8610-005-02?
Apply 15 to 415 V phase-neutral for generator sensing on DSE8610MKII 8610-005-02; also confirm protection, polarity and the approved startup procedure. -
Can a distributor quote DSE8610MKII 8610-005-02 from a shortened code?
No. Quote the complete identity DSE8610MKII 8610-005-02, manufacturer, quantity, destination, product photos and required documentation scope. -
What receiving inspection is appropriate for the load sharing controller DSE8610MKII 8610-005-02?
Inspect DSE8610MKII 8610-005-02 for the full label, connector condition, revision markings, shipping damage and consistency with DSE8610 MKII generator control systems. -
Which system record should be retained after replacing DSE8610MKII 8610-005-02?
Retain the incoming inspection, original connection record, configuration backup, measured results and service approval for DSE8610MKII 8610-005-02. -
How is the restored load sharing controller function tested for DSE8610MKII 8610-005-02?
Check status indications, diagnostics and the affected load sharing controller response, then record the final result against DSE8610MKII 8610-005-02.
READY TO VERIFY YOUR PART?
Get a DSE8610MKII 8610-005-02 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
