GE PACSystems RX3i

PROFIBUS Slave Module

Series:RX3i PacSystem
Part Number:IC695PBS301
Product Line:RX3i
Catalog:IC695
Product Type:PROFIBUS Slave Module
Backplane Support:Universal
Number of Slots:1 (single slot)
Ports:9-pin connector
Backplane Compatibility:RX3i PCI

Serial Communications Module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CMM004
Product Type:Communications module
No of ports:Two (2) RS232 / RS422 / RS485
Serial Ports:4
Physical Interface:RJ-45
Connectors:RJ45
Supported Configurations:RS-232, RS-422/485
No. of installations per rack:Up to Six (6) modules
Baud Rates:1200 baud to 115.2 kilobaud
Status LED indicators:Module OK, Port Fault, Port Status
Current rating:0.7 mA at 3.3 VDC, 0.150 mA at 5 VDC
Operating Temperature:0 to 60 degrees Celsius
Parity:Even, odd, none
Data bits:7, 8
Stop bits:1, 2

CABLE

Series:RX3i PacSystem
Part Number:IC695CBL001
Compatibility:PACSystems RX3i
Cable Type:Energy pack cable
Type of Input/Output:Analog
Termination Resistor:Yes

Universal analog input module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG600
Module Type:Universal Analog
No of Channels:Eight (8)
Number of Inputs:8 general purpose
No. of groups:Two (2)
Cold Junction Compensation:2 channels
No. of channels per group:Four (4)
Power Dissapation:5.4W max
Humidity:5 to 95%, non-condensing
Module conversion method:Sigma-delta
Module resolution:11-16 Bits
Internal Power:3.3V: 350mA; 5V: 400 mA

PACSystems RX3i Power Supply module

Part Number:IC695PSD140
Product Description:Power Supply module
Input voltage range:85 to 264 VAC 100 to 300 VDC
Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation:None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps

POWER SUPPLY

POWER SUPPLY
24 VDC
40 WATT
OCCUPIES ONE SLOT ON SYSTEM BASE

RX3i PACSystem option Module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CHS016
Product Description:Universal backplane
Grounding bar:Integrated
Module Hot-swap:Supported
Lifecycle status:Active
Mounting:Rack
No of slots:Sixteen (16)
Type:Universal backplane
Number of Slots:16
Input:+24 Volts
Recommended wire size:14 to 22 AWG
Enclosure:IP54 or greater

CPU MODULE

Series:RX3i PacSystem
Part Number:IC695CPE305
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Communication:RS-232
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Maximum Block Size:128 kilobytes

Input module, analog 16 point single ended, current.

INPUT MODULE
PACSYSTEMS RX3I
16 POINT
SINGLE ENDED
ANALOG CURRENT
HIGH DENSITY
10 VDC
0-20 MA

Analog Output module

Series:RX3i PacSystem
Brand:GE Fanuc / Emerson Automation
Output Current Range:4 to 20 mA and 0 to 20 mA
Output Voltage Range:0 to 10V and -10 V to +10V
External Supply Voltage Range:20 VDC to 30 VDC
External Power Supply Voltage Ripple:10% (maximum)

Analog output module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG728
Product Description:Non-isolated analog output module
Number of Channels:8
No of Channels:Eight (8) non-isolated
Voltage Range:0 to +10 Volts, -10 to +10 Volts
Output signals, Current:0-20 mA; 4-20 mA
Output signals:+/-10 VDC, 0-10 VDC; 0-20 mA, 4-20 mA
Current Range:0 to 20 milliamps, 4 to 20 milliamps
No. of HART Modems:Two (2)
External Current input::190 mA
Maximum current required:250mA
Maximum Output Load:850 Ohms
Current draw:340 mA maximum at 3.3V

ANALOG INPUT HART MODULE

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG626
Product Description:Non-isolated analog input module
Module Type:Analog Input w/HART comms
HART Protocol:Supported; HART Version 5.0
Current Range:0 to 20mA, 4 to 20mA, ±20mA
Input signals, Current:0-20 mA; 4-20 mA; +/-20 mA;
Humidity:5 to 95%, non-condensing
Internal Power:3.3V: 600mA, 5V: 450 mA
Overvoltage:±60 VDC continuous, maximum
Overcurrent:±28mA continuous, maximum
Open Circuit Detection time:1 second maximum
Autocalibration:Performed during power-up

PACSystems RX3i acommunication module

Manufacturer:GE Fanuc
Part Number:IC695PBM300
Product Description:Profibus Master Module
Communication interface:One (1) Profibus Master Port
Product Line:RX3i
Communication protocol:ProfiBus
Catalog:IC695
No. of supported DP slave:125
Product Type:PROFIBUS Master Module
Input data:244 Bytes
Number of Slots:1 (single slot)
Output data:244 Bytes

Redundancy Memory Xchange module

Series:RX3i PacSystem
Manufacturer:Emerson Automation
Part Number:IC695RMX128
Type:Redundancy memory module
User Memory:128 MB SDRAM
Nodes:Up to 256 per network
Configurable Network:Yes
Network Error Detection:Yes
Hot Insertion and Removal:Yes

7-Slot Rack

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CHS007
Product Description:Universal backplane
Series:PACSystem RX3i
Mounting:Panel mount
Type:Universal backplane
Current rating:600 mA at 3.3 VDC, 240 mA at 5 VDC.
Number of Slots:7
Bus connectors:PCI Bus / Serial Bus
Input:+24 Volts
Dimensions:10.43 in W x 5.8 in D x 5.57 in H
Recommended wire size:14 to 22 AWG
Enclosure:IP54 or greater
Grounding terminal:Included
Terminal Strip (TB1):Isolated +24 VDC

Genius Bus controller module

Series:RX3i PacSystem
Part Number:IC694BEM331
Product Type:Genius Bus controller module
Protocol Support:Genius
Entity Type:Master
Data Length:128 bytes per message
Communications:Global Data and Datagrams
Backplane Support:No Backplane Restrictions
Description:Genius Bus Controller
Baud rate (standard/extended):153.5 K
Bus termination:75/100/120/150 ohm resistor
Transient:1500 Volts
Current:300 mA
Voltage:5 Volts DC

High-speed counter module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695HSC308
Product Type:High-speed counter module
Compatibility:PACSystems RX3i
Product Description:High Speed Counter Module
Counters:8
Inputs:16
Output Voltage Range:4.7 to 40 Volts DC
No. of I/Os:16 inputs and 14 outputs
Outputs:14
Output Voltage Range:4.7 to 40 Volts DC
Maximum Count Rates:1.5 MHz
I/O Interrupts:Supported
Output Voltage Range:4.7 to 40VDC

RX3i Mid range controller

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CPE310
Product Description:RX3i CPU
Communication ports:One (1) Ethernet; Two (2) serial ports
Number of Slots:2
Number of Local Racks:8
Discrete I/O memory:32 K
Program Storage:10 MB of User Memory
Analog I/O memory:32 K
Processor Speed:1.1 Ghz
Boolean execution speed:0.72 ms/k
Local Rack:Up to Eight (8) local racks
Floating Point:Yes
Ethernet Port:Yes
Backplane:Universal backplane

Discrete input module

INPUT MODULE
24 DC
32 POINT
SUPPORTED BY SERIAL BUS
REQUIRES A TERMINAL BLOCK 

HIGH SPEED CONTROLLER

Series:RX3i PacSystem
Part Number:IC695CHS012
Compatibility:RX3i PACSystem, Series 90-30 and option modules
Number of Slots:12
Backplane Support:Supports both PCI and High Speed Serial
How Swap Support:Yes
Internal Power, 5VDC:240 milliamps
Internal Power, 3.3 VDC:600 milliamps
Mounting:Rack
Type:Universal backplane
Input:+24 Volts
Backplane Orientation:Horizontal

Power Supply

IC695PSA040
RX3I POWER SUPPLY
120/240VAC
125VDC
40 WATTS
OCCUPIES TWO SLOTS ON SYSTEM BASE

Ethernet interface module

Series:RX3i PacSystem
Part Number:IC695ETM001 IC695ETM001-LDAB
Product Type:Ethernet interface module
Compatibility:PACSystems RX3i
Ethernet Ports:2x 10/100 Mbps
Serial RS-232:Yes
Serial Data Rates:1200 bps to 115200 bps
Hot-swappable:Yes
Autosensing Ports:Yes
Ethernet Processor speed:200 MHz

CPU module

CONTROL MODULE
RX3I CPU
1 GHZ PROCESSOR
2 SERIAL PORTS
RS-485 / RS-232
20 MB USER MEMORY

Positive Logic discrete output module

Series:PACSystem RX3i
Part Number:IC694MDL754
No. of groups:Two (2)
Description:32-Point Output Module
No of Channels:Thirty-Two (32)
Output voltage range:10.2-30.0 VDC
Operating Voltage:12/24 Volts DC
No. of output groups:Two (2)
Output current:0.75 Amps per point
Switching Current:0.75 Amps per Point
No. of channels per group:Sixteen (16), isolated
Response time, maximum (On and Off):0.5 ms
I/O Capacity:32 Discrete Outputs