General Electric

SafetyNet Controller

SAFETYNET CONTROLLER
12 VDC
FOR USE IN SIL2 SAFETY APPLICATIONS
COMMUNICATES UP TO 64 I/O MODULES

9 slot plus power supply

Series:Series 90-70
Product Description:9-slot , rear mount, rack
Part Number:IC697CHS790
Voltage:5 Volts DC
Mounting:Panel mounting
Current:20 Amperes
VME System:VME standard C.1
Product lifecycle:Discontinued
Rear mounting:10" (255 mm) enclosure
Rack extension:Supported
Standard:VME
Front Mounting:19" Standard rack
Supported:Two (2)
Number of Slots:9
Current Required from I/O Bus:0.5 amps
Enclosure Depth:10 inches

Discrete output module

Series:Series 90-70
Manufacturer:GE Fanuc; Emerson Automation (Current)
Part Number:IC697MDL750
Rated voltage:24 to 48 Volts DC
No of Channels:Thirty-Two (32)
No. of output groups:Four (4)
Channels per group:Eight (8)
Current draw:0.25 A
Required current:0.25 Amps
Wiring configuration:Positive Logic
Output voltage range:20-60 VDC
Number of outputs:32
On response time, maximum:1 ms
Off response time, maximum:1 ms
Output signal range:20 - 60 VDC
Isolation voltage:1500 Volts

Motion Controller Module

Series:RX3i PacSystem
Part Number:IC695PMM335
Catalog:IC695
No. of Axes:4
No of Master axes:1
Backplane Support:Universal Support
Motion Path Planning:1ms
Number of Slots:1 (single slot)
Position Loop Update Rate:500μs
Controlled Axes/Module:4
FSSB Velocity Loop Update Rate:125μs
Motion Path Planning:1 ms
FSSB Torque Loop Update Rate:62.5μs
Power Consumption at 5 V:0.45 A
Servo Command Interface:Fiber Optic
Power Consumption at 3.3 V:1.1 A
Floating Point:Yes

Redundant fault-tolerant control system

Input Voltage: 24V DC
Current Consumption: 1.5A typical
Isolation: 1500V AC channel-to-channel
Trip Contact Ratings:5A @ 30V DC resistive
Analog Inputs: 8 channels  
Relay Outputs: 8 channels
Communication Ports: 2x Ethernet for diagnostics

Resistance Temperature Device

RTD INPUT MODULE
8 CHANNEL
14-BIT
15 OHMS MAX.
2 ETHERNET PORTS
FOR MARK VI TURBINE CONTROL SYSTEM

Thermocouple Input Module

IO PACK
THERMOCOUPLE
2 ETHERNET PORTS
AMBIENT TEMPERATURE RATING: 
-30 TO + 65°C (-22 TO +149 °F)

Discrete Contact Input I/O Module

Power Supply:28VDC
Functional Revision 1:A
Mark VI Series Grouping:Group 1
Number of Channels:16 (isolated)
Input Type:Dry contact (volt-free) or wet contact (24–125V DC)
Voltage Range:24–125V DC (configurable)
Input Current :2–20mA per channel
On-State Voltage:≤3V DC (for dry contact)
Off-State Leakage:<1mA

Analog I/O Module

CARD
INPUT/OUTPUT PACK
ANALOG IN/OUT
200 MA TYPE
FOR MARK VIE TURBINE CONTROL SYSTEM

Discrete input module

Series:PACSystem RX3i
Manufacturer:GE Fanuc
Part Number:IC694MDL240
Description:Input module
No of Channels:Sixteen (16)
Points:16
Input signal range:0-132 VAC
Voltage:120 Volts AC
Nominal Input voltage:0-120 VAC
Current:7 milliamps
Input Frequency:47-63 Hz
Power consumption:90 milliamps
Input current:12mA per channel
Input current:12 mA
Bus voltage:5 Volts
Current draw:90 mA (all inputs active)
Off response time, maximum:45 ms
On state current:6 mA
On response time, maximum:30 ms
Product Lifecycle Status:Active
Off state current:2.2 mA
On–state Current:6mA minimum
On response time, typical:30 ms

Power Transducer Module

Series:Series 90-30
Manufacturer:GE Fanuc (Former); Emerson Automation (Current)
Part Number:IC663PTM101
Description:Power Transducer module
Voltage:10-120 Volts AC
Mounting:Any Series 90-30 Baseplate
Current:0-7.5 Amperes
Compatible Series 90-30 CPU:Any CPU module
Dissipation:4 Watts
Frequency:35-70 Hertz
Resolution:14-bit
Total Power Dissipation:4W max
Backplane isolation Voltage:1500 Volts
Product Lifecycle Status:Discontinued/Obsolete

LAN Communications Card

TURBINE CONTROL SYSTEM
MARK V
SPEEDTRONICS
W/FIRMWARE
16 DIGIT DISPLAY

Power Excitation Board

Mark V
DS200RTBAG3AHC
Turbine Control System
Relay Terminal Board

Analog output module

Manufacturer:GE Fanuc
Series:RX3i PacSystems
Part Number:IC694ALG391
Product Type:Output Module
Module Type:Analog
Number of Outputs:2

Analog input module

Manufacturer:Emerson Automation
Series:PACSystem RX3i
Product Description:Analog input module
Part Number:IC694ALG221
No of Channels:Four (4) input channels
Product Type:Input Module
Nominal Input signal:0-20 mA; 4-20 mA
Module Type:Analog
Channel update rate:2 ms
Number of inputs:4
Digital Resolution:12 bit
Input filter response:325 Hz
Input impedance:250 ohms
Input Filter Response:325 Hz
Common Mode Voltage:200 volts

UNIVERSAL RELAY

UNIVERSAL RELAY
SERIES UR
CT/VT MODULE
3-PHASE
1A/5A

GAS DETECT IO

IS220YAICS1A
DISCONTINUED BY MANUFACTURER
GAS DETECT IO
SIL IO PACK
ANALOG IO
BPPB BASED

IO PACK

IS220YDOAS1A
DISCONTINUED BY MANUFACTURER
IO PACK
CONTACT OUT SIL

Discrete output module

Series:PACSystem RX3i
Manufacturer:GE Fanuc
Part Number:IC694MDL940
Product Description:Relay output module
Description:Relay Output Module
Response time:15 ms
Product Lifecycle Status:Active
No. of channels:Eight (8)
No. of groups:Four (4)
Switching current:2.0 Amps
No. of channels per group:Four (4)
Output voltage, range:5 - 30 VDC; 5 - 250VAC (50/60 Hz);
Max. Backplane Draw:135 Milliamps
Rated voltage:24 VDC; 120/240 VAC
Inrush Rating:5.0 Amps
Max. Response Time:15 Milliseconds
Minimum load:10 mA
Location:PacSystems PLC I/O Slots
Maximum inrush:5:00 AM

Thermocouple Input Board

Voltage: 24 V DC ±10%
Consumption: ≤15 W (typical)
Channel-to-Channel: ≥250 V AC
Field-to-System: 1500 V AC
Signal Range: -200°C to +1800°C

ETHERNET CONNECTION BOARD

PC BOARD ASSEMBLY
ETHERNET CONNECTION BOARD
CONTROLLER WITH 2 IS BUS CHANNELS
MARK VI

Discrete Input Pack

Channels:16x isolated
Voltage Range:24-125V DC
Current Rating:5mA (min)
Isolation:1500V AC
Power Supply:24V DC (±10%) from backplane
Power Consumption:6W (typical)
Response Time:<1ms (input), <0.5ms (output)
Contact Rating:50,000 operations @ rated load

Vibration Transducer Interface Module

Series: Mark VI
Product Type: Vibration Transducer Interface Module
Board rating: 125 V dc
Common Mode Voltage Range: ±5 V
Dimensions: 11.00 x 9.00 x 3.00
Operating temperature: 0 to 60 °C
No.of Analog Voltage Inputs: 6

Relay Output Terminal Board

Product Type: Relay Output Terminal Board
Number of channels: 16
Relay Type: SPDT
Relay Contact Rating: 10A
Input Voltage Range: 12V, 24V
Number of Relay Channels: 4, 8
Relay Switching Current: Max 10A
Mounting Type: DIN rail
Output Resolution: 12-bit
Output Impedance: 10 Ohm
Analog outputs: 0-20 mA

VME Analog Input board

IS200VAICH1D
MARK VI
INPUT CARD
ANALOG
VME