General Electric

Turbine Protection Input Terminal Board

Series: Mark VIe
Simplex Primary Turbine Protection Input Terminal Board
Number of inputs: 4
Number of outputs: 2
MPU pulse rate range: 2 Hz to 20 kHz
Contact voltage sensing: 20 V dc
Technology: Surface mount
Temperature: -30 to +65C

CPU module

Series:RX3i PacSystem
Part Number:IC695CPE305CA IC695CPE305CA-BCAD
Compatibility:PACSystems RX3i
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Maximum Block Size:128 kilobytes
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Floating Point:Yes
Serial Communication:RS-232
Ethernet Port:Yes

Turbine Emergency Trip Terminal Board

Mark VI
Triple Modular Redundancy (TMR) 
Input Voltage Range: 24 VDC to 125 VDC
Operating Temperature: -30°C to +65°C
Storage Temperature: -40°C to +85°C
Humidity: Up to 95% non-condensing

Turbine Emergency Trip Terminal Board

3 independent trip solenoids
Solenoid voltage typically: 
24 VDC to 125 VDC
Operating Temperature: -30°C to +65°C
Storage Temperature: -40°C to +85°C
Humidity: Up to 95% non-condensing

Protective Termination Board

Series: Mark VI
Input Voltage:  0-10 VDC
Operating Temperature: -30°C to +65°C
Storage Temperature: -40°C to +85°C
Humidity: Up to 95% non-condensing

Analog Processor Module

Series: Mark VI
Function: Analog Processor Module
Input Voltage: 125 V dc
Output Voltage: 24 V dc
Operating temperature: -30 to +65oC
Mounting: DIN-rail
Model Type: Safety I/O Pack

Eight Port Serial Controller

Form Factor
PMCPCI  PMC-422 
Signaling: 3.3V and 5V
Specification 2.2
33 MHz/32-bit
3 watts total
0.3A @ 3.3V
0.4A @5V
Eight rear RS485/RS422/RS232 serial ports
Four RS232 ports on front; RJ45 connectors 
(frontports are not available for RS485 and RS422)

RTD Input Terminal Board

Function: RTD Input Terminal Board
Series: Mark VIe
Number of Channels: 8
Operating temperature: 0 to 60 o C
Input voltage: 125 V
Total Output: 400 W

Analog Input Terminal Board

Voltage Input:  ±10V, 0-10V, or 0-5V
Current Input:  4-20 mA
Nominal Supply Voltage: 24 VDC
Power Consumption:  250 mA
Operating Temperature: -40°C to +70°C (-40°F to +158°F)
Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Humidity: 5% to 95% non-condensing

TERMINATION BOARD

Span: 0.3532 to 4.054 V
Size: 17.8 cm high x 33.02 cm wide
Technology: Surface mount
Temperature Operating: -30 to 65oC
Product Type: Servo Terminal Board

Terminal Board

Series: Mark VI
Product Type: Terminal Board
Trip Solenoids: 3
Solenoid Rated Voltage/Current: 125 V dc
Solenoid Response Time: L/R time constant is 0.1 sec
Current Suppression: Metal oxide varistor
Control Relay Coil Voltage Supply: 28 V
Flame Detector Supply Voltage/Current: 335 V dc
Flame Detectors: 8

Sink I/O terminal block

Input voltage range: 10-30V DC
Output voltage: 24V DC typical
Input: Up to 2mA per channel
Output: Rated for up to 2A per channel
Wiring Capability:  typically 16-24 AWG
Operating Temperature: -40°C to +60°C
Humidity Tolerance: Up to 95% non-condensing

DC sink I/O terminal block

Series:Genius I/O
Voltage Ratings:12/24 Volts DC
Operating Temperature:0 to 60 degrees Celsius
Storage Temperature:-40 to 100 degrees Celsius
Relative Humidity:5%-95%, Non-condensing

Terminal block

Voltage Rating: Up to 250V AC/DC
Current Capacity: Typically up to 10A
Operating Temperature: -40°C to +70°C
Humidity Tolerance: 
Up to 95% non-condensing

Micro Controller

DC Inputs: 16
DC Outputs: 1 (24 V)
Relay Outputs: 11 (Normally-Open), 2 A
Nominal Power Requirement: 100-240 V
Voltage Type: DC
Series: VersaMax

I/O Expansion Unit

Power Supply:DC 24V
Digital Input: Typically 24V DC
Operating Temperature: 
Typically 0 to 50°C (32°F to 122°F)
Storage Temperature: 
Typically -20°C to 70°C (-4°F to 158°F)
Humidity: 30% to 85% RH, non-condensing

Expansion Unit

EXPANSION MODULE 
PLC 90-10A 
ADDITIONAL UNIT 1/056

Embedded Single Board

Up to 512MB PC100 SDRAM
(PC133 stepped down to 100 MHz)
Built-in SVGA support with 4 Mbytes DRAM display cache
Built-in dual 10/100 Mbit Ethernet
IDE drive support
Floppy drive support
Two RS232 serial ports
Dual USB ports
Real-Time clock/calendar
Front panel reset switch
Miniature speaker
Keyboard/Mouse port

CONTROL COMMUNICATION GATEWAY

Input Voltage: 24 VDC nominal 
Power Consumption: ≤ 15 W
Ethernet Ports: Dual 10/100 Mbps
Operating Temperature: -30°C to +70°C (-22°F to +158°F)
Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Humidity: 5% to 95% non-condensing
Data Transfer Rate: Up to 100 Mbps

SPINDLE DRIVE BOARD

POWER CONNECTION MODULE
DC300 SPINDLE DRIVE BOARD
CNC
Input/Output: typically 0-10V, 4-20mA
Operating Temperature Range: Typically -40°C to +70°C
Power Input: Receives AC or DC

MICRO ANALOG BOARD

Input/Output: 
typically 0-10V, 4-20mA
Operating Temperature Range: 
Typically -40°C to +70°C
Function: 
Processes and converts analog signals

Digital I/O Module

Nominal Voltage Options: 
24 VDC, 48 VDC, 125 VDC, or 250 VDC.
Input Voltage Range: ±20% of nominal value
Logic 0 (Low): 0-3 V
Logic 1 (High): 15-250 V 
Operating Temperature Range: -40°C to +70°C
Storage Temperature Range: -40°C to +85°C
Humidity: 5% to 95% (non-condensing)

CONTROL COMMUNICATION GATEWAY

Power Supply: Typically 24V DC
Operating Temperature Range: Typically -40°C to +85°C
Storage Temperature Range: -40°C to +85°C.
Humidity: humidity up to 95% (non-condensing).

TB Option Card

the DC-300 drive
Operating Voltage  24V DC
Operating Temperature Range: -10°C to +60°C
Storage Temperature Range: -20°C to +70°C

CMOS MEMORY BOARD

PC BOARD ASSEMBLY
CMOS MEMORY BOARD
Memory Capacity: 128KB to 1MB
Operating Voltage:operates on +5V DC
Operating Temperature: 0°C to +60°C 
Storage Temperature: Typically -40°C to +85°C.
Humidity: Generally 5% to 95% non-condensing