ABB

Circuit Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 15W (typical)
Operating Current: 0.5-1A
Isolation Voltage: 2000V AC 
Main Processor: 32-bit DSP or microcontroller
Clock Speed: 100-200MHz

IGCT MODULE

Voltage Rating:4500V (VCES)
Current Rating:4000A (IT(RMS))
Max. Turn-off Current:6000A (ITGQM)
On-State Voltage Drop:1.85V (typical @ 4kA)
Switching Frequency:Up to 500Hz 
Gate Driver Voltage:±20V (isolated)

Power supply module

Input Voltage Range:85-264V AC (47-63Hz) 
Output Voltage: 24V DC (±1% regulation)
Output Current: 10A 
Power Rating: 240W
Inrush Current: <30A (at 230V AC)
Overvoltage Protection: 28V DC 
Overcurrent Protection: 110-130% of rated current
Line Regulation: ±0.5% (85-264V AC)
Load Regulation: ±1% (20-100% load)

Driver board

Model Number: UF C911B108 3BHE037864R0108
Input Voltage: 24V DC 
Output Voltage: Adjustable based on application requirements
Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Storage Temperature: -40°C to 85°C (-40°F to 185°F)
Humidity Range: 5% to 95% (non-condensing)

Communications I/O Module

Supply Voltage: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Primary Protocol: Profibus DP
Data Rate: 9.6kbps to 12Mbps
Connector Type: 9-pin D-sub
Isolation: 1500V AC
Digital Inputs: 8 channels

Communications I/O module

Supply Voltage:24V DC (±10%)
Power Consumption:4W (typical)
Inrush Current:<15A (20ms)
Backplane Current:500mA max
Output Isolation:3000V AC
Data Rates:9.6 kbps – 12 Mbps
Connector:9-pin D-sub (RS-485)
Address Range:0–126
Isolation:1500V AC

Exciter Control Module

Supply Voltage: 110/220V AC ±10%
Power Consumption: ≤15W
Generator current: 0-5A AC (CT input)
Field voltage: ±200V DC
Field current: ±5V DC
Response Time: <20ms for 95% step response

Control Board

Supply Voltage:24V DC (±10%)
Power Consumption:≤10W
Isolation:1500V AC
Processor:32-bit RISC microcontroller/DSP
Clock Speed:100-200 MHz
Analog Inputs:4-8 channels
Digital I/O:8-16 channels

Power Supply Module

Input Voltage:3-phase: 380-480V AC (±10%), 50/60Hz
Output Voltage:24V DC (±1%)
Output Current:20A (continuous)
Power Rating:480W
Efficiency:>92% (at full load)
Inrush Current:<40A (at 480V AC)

Control Board

Supply Voltage: 24V DC (±10%)
Power Consumption: 8W (typical)
Processor: 32-bit DSP
Clock Speed: 150 MHz
ADC Channels: 16-bit, 12 channels
Analog Inputs:6 channels 
Isolation:2500V AC

Control Board

Processor: Dual-core 32-bit DSP 
Clock Speed: 300 MHz
Power Supply: 24V DC 
Power Consumption: 12W (typical)
Isolation:3000V AC
Control Loop Speed: 25μs (basic)
PWM Resolution: 16-bit @ 8kHz
Protection Response: <10μs 

Control Module

Supply Voltage:24V DC 
Processor:Triple-core 32-bit DSP
Clock Speed:400 MHz 
Memory:512KB SRAM
Power Consumption:18W (typical)
Analog Inputs:12× 18-bit ΣΔ ADC (±15V, 500kS/s)
Analog Outputs:6× 16-bit DAC (0-10V/4-20mA)
Digital I/O:24× configurable (5V TTL to 30V DC)

Control board

Supply Voltage: 24V DC
Power Consumption: 6W typical
Isolation:2500V AC
Processor: 32-bit RISC
Clock Speed: 216 MHz 
Memory SRAM: 256KB
Analog Inputs:6 channels
Digital I/O:12 opto-isolated inputs 

INVERTER INTERFACE BOARD

Supply Voltage:24V DC (±10%)
Power Consumption:≤5W
Isolation Voltage:2500V AC (input-to-output)
Analog I/O:Range ±10V, 4-20mA
Digital I/O:24V DC 
Overvoltage:Auto-cutoff at 30V DC
Short Circuit:Current limiting
ESD Protection:±8kV (all ports)

Touch screen

2x Ethernet 10/100Mbit
1x RS-232/-422/-485
2x USB 2.0 Host
1x SD-card slot
2x Expansion slot
Storage capacity user data: 256 MB
Storage type user data: Flash Disk
Storage type user program: DDR RAM
Power consumption (@Pcons): 24 W
Power supply: 24 (18 ... 30) V DC
Screen colors: 64k colors

IMAGING CARD

Supply Voltage:24V DC (±5%)
Power Consumption:25W (typical)
Isolation :1500V AC 
Sensor Interface:GigE Vision (2 ports)
Camera Support:Up to 8MP resolution @ 60fps
Pixel Depth:8/10/12-bit
Throughput:2.5 TOPS (INT8)

Control Unit

Processor: Dual-core 32-bit RISC processor
Clock Speed: 800 MHz
Ethernet:4× 10/100/1000 Mbps (RJ45)
Serial:2× RS-485 (Modbus RTU)
IEC 61850:MMS, GOOSE, SV (Class 1)
Fieldbus:PROFIBUS DP-V1 (optional)
Power Supply: 48-250V DC or 100-240V AC
Power Consumption: 15W (typical)
Isolation: 4kV AC

Charging controllers

Input Voltage:380-480V AC, 3-phase (±10%)
Output Voltage:115 V AC or 230 V AC  ±10%, 50/60 Hz
Current Rating:20A (continuous), 30A (peak)
Efficiency:>94% (at full load)
Power Factor:>0.98 (at full load)
Overvoltage:+15% of setpoint
Overcurrent:110% for 60min
Reverse Polarity:Instant cutoff
Short Circuit:<1ms response

Servo Motor

Rated Power:4.5 kW
Rated Torque:28 Nm
Peak Torque:84 Nm (300% overload)
Rated Speed:1500 rpm
Max Speed:5000 rpm
Voltage:400V AC (3-phase)
Current:9.5A (rated), 28A (peak)
Torque Constant:1.8 Nm/A
Back EMF:110 V/krpm
Rotor Inertia:0.012 kg·m²
Stator Resistance:0.8 Ω (line-to-line)
Thermal Time Constant:45 minutes

REF542plus HMI Unit

Supply Voltage:24V DC (18-36V range)
Power Consumption:8W (typical)
Isolation :2kV AC 
Display Type:5.7" TFT LCD (color)
Resolution:320 × 240 pixels
Touch Panel:Resistive (single-touch)
Backlight:LED (50,000h lifespan)
Ethernet:10/100 Mbps (IEC 61850 MMS)
Optical Port: IR interface for local config
USB:Type B

Multi flame detector - control unit

Power Supply:120-220 Vac +/- 20%, 
45-65 Hz 24Vdc +/- 20%
AC input: 30 VA (6A / 5 ms inrush current)
DC input: 22 W (24A / 2 ms inrush current)
Operating: 0 - 60°C (32 - 140°F)
Storage: -25 - 85°C (-13 - 185°F)
Contact rating: 250 Vac 3 A 750 VA cosΦ 0.4
220 Vdc 300 mA 66 W

16 Bit Profibus DP Adapter Module

Up to 12 Mbps.
Auto-detection of baud rate
Address Range: Configurable from 0 to 126
Supply Voltage: 24 VDC ±10%.
Power Consumption: < 2 W
Operating Temperature: -10°C to +55°C.
Storage Temperature: -40°C to +70°C

CONTROL CIRCUIT BOARD

Input Voltage: +5V, +12V
Current Consumption: Typically under 2A
RS-232/RS-485
Operating Temperature: 0°C to 50°C.
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 85% (non-condensing)

Traction Voltage Sensors

Nominal primary voltage:2000V r.m.s
Measuring range:±3000
Primary turn number:20000
Secondary turn number:2000
Secondary current at UPN:50
Accuracy at UPN:≤±1
Offset current:≤±0.3
Linearity:≤±0.1
Thermal drift coefficient:-25 … +70°C ≤±5 

Power Supply Rack

Overvoltage:28V DC
Input Voltage:400-480V AC, 3-phase (±10%)
Output Voltage:24V DC regulated
Output Current:50A (continuous), 60A (peak)
Power Rating:1.2kW (per module)
Efficiency:>93% (at 50% load)
Power Factor:>0.95