









G120 Standard Control Unit
SINAMICS G120 CONTROL UNIT
CU240E-2 E-TYPE SAFETY INTEGRATED
STO RS485-INTERFACE
USS-PROTOCOL 6DI, 3DO, 2AI, 2AO
MAX 1F-DI PTC/KTY INTERFACE
USB- AND SD/MMC-INTERFACE
PROTECTION IP20
AMBIENT TEMP 0 TO +50 DEG C
WITHOUT POWER MODULE AND PANEL
Driver Board
HV-IGBT modules: 1900A
Input Voltage Range:+24V DC
Isolation Voltage:min. 4000 V RMS
IGBT Voltage Monitoring:±5%
Gate Drivers Per Phase:2 channels
IGBT-TRANSISTOR MODULE
IGBT-TRANSISTOR MODULE
PRECHARGING RESISTOR 2 X 18 OHM
Voltage: 1500 V
DC Collector Current:160 A
Rated Pulse Current:320 A
Operating Junction Temperature:-40°C to +150°C
Genset Controller
EASYGEN 3200-5P2
Voltage Monitoring: 50–600 V AC
Current Monitoring: 1–5 A
Frequency Range: 40–70 Hz
Digital Inputs: 16
Digital Outputs: 8
Analog I/O: 4–20 mA/0–10 V DC
Operating Temperature: -40°C to +85°C
Storage Temperature: -50°C to +105°C
Isolated Analog Input Module
Input Channels: 8 or 16 channels
Channel-to-channel: 1500 V AC
Field-to-system: 2500 V AC
Current: 4–20 mA, 0–20 mA
Current: 4–20 mA, 0–20 mA
Power Supply: 24 V DC ±10%
Accuracy: ±0.05%
Current Transformer
CURRENT TRANSFORMER
2000 AMP
15-24VDC
AC Input Range: 0–2000 A AC
Overload Capacity: 130% of Ipn for 10 sec
DC Voltage or Current:4–20 mA (Two-Wire Loop)
Input Voltage: 15–24 V DC ±10%
Power Consumption: <2 W
SINAMICS DC LINK ADAPTER
SINAMICS DC link adapter set
for multi-tier configuration
Screw terminals 35-95 mm2
for all Line/Motor Modules
BUSBAR CURRENT TRANSFORMER
Primary Current (Ipn): Range 50–600 A
Secondary Current (Isn):1 A or 5 A
Frequency: 50/60 Hz
Insulation Voltage:720 V AC
Operating: -25°C to +60°C
Storage: -40°C to +70°C
PSB11-BOARD
PSB11-BOARD/R3 SIC
HP/MC - SINAMICS COMPONENTS (LD)
Link Voltage (DC): Supports 600/510–720 V D
Output Voltage (AC): Up to 480 V AC 3-phase
Continuous Motor Current: Up to 1,600 A
Peak Current: Short-term 2,500 A
Switching Freq: Up to 5–20 kHz

Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.