Outputs per module:32
Galvanic Isolation:2 groups of 16 outputs
Operating Voltage:10.5 to 32 VDC
Output Type:High side driver
Peak Voltage:32 VDC
AC Frequency:N/A
ON Voltage Drop:0.15 VDC @ 0.5 A load
EC402 ESB Bus Coupler Module
5 Standard type with no explosion protection
E Standard type with explosion protection
0 Basic type
1 With ISA Standard G3 option
Operating Voltage:24 V DC
Operating Temperature:-40°C to +85°C (-40°F to +185°F)
Humidity:5–95% RH (non-condensing)
SIMATIC S7-200 SMART
CPU SR60, CPU, AC/DC/relay
onboardI/O: 36 DI 24 V DC
24 DO relay 2A; Power supply
AC 85-264 V ACat 47-63 Hz,
Program/data memory 50 KB
PowerFlex 753 AC Drive, with Embedded I/O
Standard Protection, Forced Air, AC Input with DC Terminals
Open Type, 22 Amps, 11kW ND, 7.5kW HD
400 VAC, 3 PH, Frame 2, Filtered
CM jumper installed (preferred)
DB Transistor, Blank (No HIM)
Experience gained from over 100,000 units installed worldwide
Improved reliability
Optional HART® over 4-20mA output
Can detect a wide range of hydrocarbon gases including solvents
Increased reliability with no moving parts
Increased stability from self compensating optics
Immune to long term component drift
Remote functional gas test facility
Response time: T50 < 3 seconds, T90 < 4 seconds (methane)
Operational and certified: -40° to + 65°C temperature range
Number of Phases:3-phase
Degree of Protection:IP21
Enclosure Type NEMA:Type1
Altitude:1000 m
Operating Humidity (RHamb):5 ... 95
Sound dB (A):63 dB(A)
Frequency (f):47.5 ... 63 Hz
Frame Size:R5
Input Voltage (Uin):380 ... 480 V
Signal :Accepts from 1 to 4 proximityprobe signals
InputImpedance:10 kΩ
Peak-Peak filter Fixed:1 Hz to 600 Hz
Gap filter: -3 dB at 0.09 Hz
Average pistonposition Fixed:1 Hz to 600 Hz
Average Gap:-3 dB at 0.09 Hz
Input Voltage:24V DC ±10%
Gate Drive Output:+15V/-8V (typical for IGBTs)
Isolation Voltage:2500V AC
Current Sensing Accuracy:±1% of full scale
Switching Frequency:Up to 20kHz
Fiber optic for control signals
Terminal blocks for power connections
Multi-pin headers for auxiliary signals
DC Input 18~36 Vdc, max 7.5 W
Configurable Bandpass filter 0.2 Hz to 20 kHz
Scale Factorrange 5 to 1000 mV/g
Full scale range 2 to 80 g peak
Current Sink Source 3.3 mA ± 5%
Open Circuit Voltage -21 to -24 Vdc
Emitter Voltage:1700V
Collector Current: 300A @ 80°C
Pulsed Current : Up to 600A
Switching Frequency: Up to 20kHz
Low Saturation Voltage:2.0V
Isolation Voltage: 2500V AC (min)
Supply Voltage: 24V DC (±10%)
Power Consumption: <5W (typical)
Operating Current: 200mA @ 24V DC
Communication Speed: Up to 12Mbps
Optical: ST or BFOC type
Electrical: Terminal block or D-sub
330104 3300 XL 8 mm Probe
M10 x 1 thread,with armor
Minimum unthreaded length: 80 mm
Minimum case length: 160 mm
10 1.0 meter (3.3 feet)
02 Miniature coaxial ClickLocconnector
standard cable
00 Not required
Interface:RS-422/RS-485
Communication function:Half-duplex
Transmission code :ASCII/binary
Character length:7/8 bits
Stop bit length:1/2 bits
Lag time after data transmission:1 ms
Transmission distance:Maximum 1200 m
Number of outputs 16-channel, module isolation
Output voltage 24 V DC
Output voltage drop 1 V maximum
External power supply rating 24 V DC, 3.4 A minimum
Maximum leak current at output off status 1.6 mA
Output format Current source
Minimum load current 35 mA
Load resistance range 120 to 685 Ω
Output response time 30 ms maximum
24 binary outputs with enclosed relays (NO contacts)
Current carrying capacity of the relays: max. 1 A
Channel-by-channel isolation of the outputs
Module is capable of redundant operation
Monitoring of the module
Counter for switching cycles (channel by channel)
Rated Current (In): 1 A or 5 A
Current Input: ≤ 0.1 VA
Frequency Range: 45–65 Hz
Binary Inputs: 5 (24–250 V DC/AC)
LED Indicators: 9 (Trip, Start, Alarm, Ready, etc.)
Operating Temperature: -25°C to +55°C
Storage Temperature: -40°C to +70°C
Humidity: ≤ 95% RH (non-condensing)
Supply Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Isolation: 500V AC
2x RJ45 Ethernet ports
USB port for local configuration
8 digital inputs (24V DC)
4 digital outputs (24V DC, 0.5A)
2 analog inputs (±10V or 0/4-20mA)
2 analog outputs (0/4-20mA)
Supply Voltage: 24V DC (±10%)
Power Consumption: 2W
Backplane Current: 1A maximum per slot
Isolation: 500V AC
System Connection: S800 bus to main controller
Field Connection: Screw terminals for I/O wiring
Bus Speed: 1.5Mbps
