ALL MANUFACTURERS

Velomitor Piezo-velocity Sensor

Sensitivity3.94mV/mm/s (100 mV/in/s)±5%
Velocity Range 1270 mm/s (50 in/s) peak.
TransverseSensitivityLess than 5% of sensitivity
AmplitudeLinearity±2% to 152 mm/s (6 in/s)peak. 
Output BiasVoltage-12 ±3.0 VDC
overtemperature referenced toPin A
DynamicOutputImpedanceLess than 2400 Ω
Grounding Case isolated 

BASE UNIT TYPE A1 BU15-P16+A0+2D/T

Flash Memory Card - 256 MB

Base Unit

3300 NSv Proximity Probes

330910 3300 NSv Probe
M10X1 thread, witharmor
Minimum unthreaded length:0 mm
Minimum length: 120 mm
10 1.0 meter (39 in)
02 Miniature coaxial ClickLoc connector
standard cable
00 Not required

BRC400 Bridge Controller

CONTROLLER
HARMONY BRIDGE
BRC400
BUTTON CELL BATTERY
SINGLE PORT
RELAY OUTPUT

PS307 Power Supply - Outdoor Version

35mm-Simatic Stand.Sectional Rail

CPU 414-3 Central Processing Unit

Servo Control Board

Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs

CM DP FOR ET 200SP CPU

ET200SP, CM CAN Gateway to CAN

PC BOARD

JINTC1C
PC BOARD
PCB FOR ACS850-04-035A-5+E200+J400
ACS880 SERIES

DC drive motherboard

Memory:32MB SDRAM
Control Loop Time:100μs (speed)
Digital I/O:12x 24V DC inputs
Supply Voltage:24V DC ±10%
Power Consumption:15W max
Isolation :2500V AC 

Infeed Module

Relay Output module

Series:PACSystem RX3i
Part Number:IC694MDL930
No of Channels:Sixteen (16), individually isolated
Description:AC/DC Voltage Output Module
No. of channels:Eight (8), individually isolated
Operating Voltage:5 to 30 Volts DC or 5 to 250 Volts AC
Contact form:Normally Open (N.O.) Form A contacts
Output voltage range:5-250VAC / 5-30 VDC
Nominal output voltage:120-240 VAC; 24 VDC
Max. Backplane Draw:6.0 Milliamps
Minimum load:10 mA
Inrush Rating:5.0 Amps
Maximum inrush:5:00 AM
Relay contact life:150,000 -1,000,000 operations

CPU 1513-1 PN. 300KB PROG.. 1.5MB DATA

Control Board

Clock Speed:150MHz (DSP), 100MHz (FPGA)
Memory:512kB Flash, 68kB SRAM
Operating Voltage:24V DC ±10%
Power Consumption:12W typical
Isolation:2500V AC
Control Loop Update: 62.5μs (speed)
Analog Inputs:2 ch (16-bit, ±10V/4-20mA)
Digital Inputs:6 ch (24V DC, 3ms filter)
Relay Outputs:3 ch (250V AC/5A)
PTC Input:2 ch (Motor temp sensors)