ALL MANUFACTURERS

Analog Input Module

Input Channels :16 Channels
A/D Converter Resolution:16 bits
Input Range:1 4-20 mA only (through 200 Ω)
Normal Mode Rejection Ratio, at 60 Hz:19 dB
Maximum Normal Mode Input: ± 30 Volts
Crosstalk, dc to 60 Hz (channel-to-channel):-60 dB
Input Scan Rate:50 ms

Analog Output Module

Power supply:24V DC
Rated Current:55mA at 24V
Power Consumption:1.32W at 20mA
Power/DCS to Field:1500 VAC
DCS side connections:
37 pin DSUB connector on CC-UGIA01
Voltage Input:24V DC
Interface to DCS:4 to 20mA with HART

MLink Control Unit

Model: M-Link (Motor Link)
Series: ABB MNS iS Intelligent MCC System
Processor:ARM Cortex-A9 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
MCC Bus Interface:MNS Connect
Operating Voltage: 110-240V AC (50/60 Hz)
Power Consumption:≤ 15 W

Drive Control Board

Control Methods:DTC 
Communication:Embedded
Operating Voltage:24 V DC (±10%)
Power Consumption:30 W (typical)
Memory:512 MB DDR3 RAM, 4 GB Flash

Current Input Module

Number of input channels 16 channels, module isolation
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C
Withstand voltage 1.5 kV AC between input signal and system for 1 minute

UNITROL 1010 Voltage Regulator

Generator Voltage:100–690V AC (50/60 Hz), 
Field Voltage (Output):10–250V DC
Regulation Accuracy:±0.5% 
Response Time:<30 ms 
Auxiliary Supply:24/48/110/250V 
Power Consumption:≤25 W (standby)

Handheld communicator

Mobility MFC Hand Held Configuration Device
Display:4.3" TFT LCD 
Touchscreen:Capacitive (glove-friendly)
Processor:ARM Cortex-A8 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
Charging:AC adapter (100–240V)
Operating System:Linux-based RTOS

Input Module

Number of inputs 16-channel, module isolation
Input current 6 mA ± 20 % 
Contact rating 24 V DC +20 % / -10 % 
External power supply 24 V DC +20 % / -10 % 
Input response time 40 ms maximum
Withstand voltage (*1) (*2) 2 kV AC 
between input signal and system for 1 minute
16-input line collectivelyconnected

Power Voting Unit

Input Channels:24V DC signals
Response Time:<10 ms
Operating Voltage:24V DC
Power Consumption:≤ 5 W
Isolation:1.5 kV AC

POWER SUPPLY BOARD

Acs880/580 Series Inverter
Input Voltage: 1-phase/3-phase input 
AC Input: 200–500 VAC
DC Input: 500–700 VDC
Frequency: 50/60 Hz
Output Power: ≤ 100 W
Output Voltage: Supplies +24 VDC
Load Capacity: 5 A @ 24 VDC

MC INTERFACE BOARD

Input Voltage: Typically 24V DC
Output Signals: Digital and analog signals for 
motor control and feedback.
Current Consumption:100-500mA 
Communication Voltage Levels: 3.3V or 
5V logic levels for digital communication.

Touch screen

Screen Size: 7 inches (diagonal).
Resolution: 800 x 480 pixels.
Display Type: TFT LCD with vibrant colors and excellent contrast.
Touch Screen Type: Resistive touch for accurate and reliable input.
Brightness: 400 cd/m².
Colors: 65,536 colors for sharp and detailed visualization.
Viewing Angle: ±70° )

Main Control Board

DCS880
SDCS-CON-H01
Main Control Board
Operating Voltage:24 V DC (±10%)
Current Consumption:≤1.5 A
Digital I/O Channels:32 optoisolated DC I/O points
Analog I/O:±10 V DC / 4–20 mA

ACS880 AC Drive- 500V, 3PH, wall mount, regenerative

LV AC industrial wall-mounted regenerative single drive
Input Supply:3-phase 380–480V AC (±10%), 50/60 Hz
Output Power:5.5 kW (7.5 HP) @ 400V AC
Output Current:21 A continuous (40°C ambient)
Overload Capacity:110% for 60s, 150% for 2s
Output Frequency:0–500 Hz (motor-dependent)
Efficiency:>98% (at full load)
Power Factor:0.98 (min)

Digital Output Module

INPUT/OUTPUT CARD DIGITAL OUT RELAY
8 CHANNELS
0-60 DEGREES CELSIUS OPERATING TEMPERATURE
250 VAC
30 VDC
4 AMPS MAX PER RELAY
40MA MAX AT 5 VDC
200MA MAX AT 24 VDC