PART NUMBER SEARCH
AMIKONG EXCESS CONTROL SYSTEM PARTS
Specializing In:Automation Spares(DCS, PLC, CNC) Servo Drives HMI Power supplies Controllers
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
In Stock
Fast Shipping Available
· Product image is representative; revision or series may vary. Contact us to request a specific version.
- Customs & Documentation
Customs & Documentation
HS classification and country of origin are stated as commercial references and confirmed on the written quotation and shipping documents.
- Payment
Payment
Payment is accepted by bank transfer (T/T) in the currencies confirmed in the written quotation.
- Product Condition
Product Condition
Product identity, label, visible condition and packing are checked against the written order before dispatch.
-
20+
years in automation -
ISO 9001
certified quality system -
12 months
amikon warranty -
2-hour reply
from your account manager -
Success Story
solutions in action
-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
SEE PRODUCTS IN SEARCH PAGE ()
PRODUCT DESCRIPTION
135462-01 monitoring circuit board
Bently Nevada 135462-01 is a monitoring circuit board for the 3500 System. It is used to 5-95% non-condensing. Confirm the complete article identity, electrical limits, interfaces, companion hardware and controlled commissioning procedure before ordering.
BEFORE YOU BUY
Confirm the complete monitoring circuit board
ACTUAL APPLICATIONS
Application context for 135462-01
Manufacturer documentation places the Monitoring Circuit Board in practical vibration applications. The three cases below describe different operating tasks in which 135462-01 performs its documented product-family role with the configured companion equipment.
- 01 · WATER & WASTEWATER
Govern high-lift pump protection with Monitoring Circuit
At the control layer of the radial bearings and shaft-position probes, 135462-01 handles its designated signal or control duty as a Monitoring Circuit Board. During peak-flow operation, the system uses this function to observe shaft behavior while hydraulic demand rises, helping it support protection of the critical pumping duty. - 02 · MINING & METALS
Maintain conveyor-drive diagnostics with Monitoring Circuit
For the coordinated operation of the gearboxes, pulley bearings and drive motors, 135462-01 serves its documented function as a Monitoring Circuit Board. During loaded belt start, the system uses this function to compare drive-train signals through acceleration, helping it identify developing gearbox or alignment behavior. - 03 · POWER GENERATION
Maintain gearbox condition monitoring with Monitoring Circuit
Inside the gear meshes, bearings and speed references, 135462-01 serves its documented function as a Monitoring Circuit Board. During coast-down, the system uses this function to retain the signal trend as rotational speed decreases, helping it provide evidence for the next diagnostic review.
Technical specifications for 135462-01
-
Product Model135462-01
-
Product Parametersmonitoring circuit board
-
In stock1 unit
-
ManufacturerBently Nevada
-
Operating Temp-20°C to +70°C
-
Storage Temp-40°C to +85°C
-
Humidity5-95% non-condensing
-
Vibration5g (10-2000Hz)
-
Shock50g, 11ms
-
Exact Part Number135462-01
-
Product Family3500 System
-
Component TypeMonitoring Circuit Board
-
Channel Capacity2 channels
-
Rack SpaceOne full-height slot
-
Backplane Supply3500/3300 rack power
-
Input TypeCondition-monitoring transducer
-
Alarm OutputsAlert and Danger levels
-
Status LEDsOK, TX/RX and Bypass
-
Buffered OutputFront-panel transducer signal
View all additional
Alternative Names
135462 01
3500 System monitoring circuit board
Bently Nevada monitoring circuit board
SYSTEM & REPLACEMENT CHECK
Information needed before ordering
Three direct checks to secure your system integration and minimize ordering risks.
Information
System integration
Replacement check
Manuals & support
SYSTEM INTEGRATION
Match 135462-01 to the installed 3500 System
Bently Nevada 135462-01 is a monitoring circuit board used in the 3500 System. Use 135462-01 in the documented 3500 System measurement or protection channel. Match the exact order code, installed position, signal range and monitored machine function before work.
Photograph terminals, coaxial connectors, shields, earth points, rack slot and adjacent hardware before removing 135462-01. Restore each connection to the controlled drawing. Confirm 50g, 11ms, 135462-01, the exact mechanical position and the approved system configuration before connection.
After installing 135462-01, check transducer supply, gap or zero, signal response, alarms and rack diagnostics. Record the measured values before releasing the machine channel. Use qualified personnel, keep the applicable manufacturer instructions at the work location and retain the measured results with the equipment service record.
Features:
- Exact identity: 135462-01
- Product class: monitoring circuit board
- Family: 3500 System
The Bently Nevada 135462-01 requires documented system integration before energising the equipment.
REPLACEMENT CONTROL
Verify the complete 135462-01 identity before exchange
Replace 135462-01 only after matching the full article identity, monitoring circuit board, installed monitoring circuit board and documented system role. A similar family name or physical outline does not establish interchangeability.
Before removal, photograph the product label, mounting position, one full-height slot, cable routing, shields, earth connections and adjacent assemblies. Preserve the approved configuration or parameter backup for recovery.
After installation, restore all controlled settings and complete front-panel transducer signal. Review status indications and diagnostics, test the affected function at a safe operating point, and record the final maintenance acceptance evidence.
Features:
- Exact identity: 135462-01
- Connection: One full-height slot
- Test: Front-panel transducer signal
The Bently Nevada 135462-01 requires documented replacement verification before energising the equipment.
DOCUMENTATION STATUS
Browse the Manuals, Datasheets, Official Documents, Links
Important Notice: Official documents are provided through manufacturer links. Accessories, manuals, cables, calibration data, software and certificates are included only when listed in the quotation.
Features:
- Technical values prepared for 135462-01
- Bently Nevada documentation matched to 3500 System
- Exact product identity required before service
Documentation for Bently Nevada 135462-01 must match the installed equipment and complete product identity; confirm manual applicability before service.
Also searched as
Important notice
Manuals, software, firmware, cables, calibration data and accessories are included only when listed in the quotation. AMIKON is an independent supplier and is not affiliated with or authorised by the manufacturer.
This content has been produced using multiple sources. Takes no responsibility for the accuracy of this information. Always consult the original equipment manufacturer for the most up to date instructions and information.
BUYER INFORMATION
Commercial terms without hidden steps
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
01
Shipping & delivery
-
DispatchEligible stock: same / next day
-
CarriersDHL, FedEx or UPS
-
Ship fromXiamen, China
-
Packed size2.5 × 18.5 × 14cm
-
Shipping weight0.96 kg
-
-
02
Payment & customs
-
PaymentBank transfer (T/T)
-
CurrenciesUSD · EUR · GBP · RMB
-
Credit cardsNot accepted
-
HS reference8537101190
-
OriginUSA
-
-
03
Warranty & returns
-
Warranty12 months from AMIKON
-
InspectionLabel, condition and packing checks
-
ReturnsPrior RMA authorisation required
-
CompatibilityConfirm before order
-
OEM warrantyDoes not apply
-
Your written quote confirms the product identity, price, availability, lead time, warranty and shipping terms before payment.
-
Part checked
Full suffix recorded -
Condition checked
Label and appearance -
Packing checked
Antistatic protection -
Tracking supplied
Established couriers -
Sandy Lin
Dedicated account manager · 15+ years
FREQUENTLY ASKED QUESTIONS
Questions buyers ask about 135462-01
Direct answers about identity, compatibility, stock, warranty, payment and shipping.
-
Which documents should accompany a quotation for 135462-01?
Request the data sheet, installation instructions and an applicable manufacturer manual for 135462-01 when available. -
How should the monitored machine channel be protected during a 135462-01 exchange?
Bypass or trip-manage the affected protection channel under the approved site procedure before exchanging 135462-01. -
What signal-range checks should engineering complete for 135462-01?
Compare the documented input, output, range and frequency values for 135462-01 with the installed channel. -
What commissioning measurements release 135462-01 to service?
Check supply, zero or gap, live signal, alarm thresholds and diagnostics for 135462-01; retain measured results. -
What spare-part condition evidence is useful for 135462-01?
Request clear condition photos, serial or revision labels, test status, warranty scope and packing details for 135462-01. -
Which nameplate and order-code fields identify 135462-01 for a distributor?
Quote the complete 135462-01 code, 3500 System, component type, revision markings and quantity. -
Which transducer or rack compatibility details apply to 135462-01?
Match the probe, extension cable, Proximitor, monitor slot or rack interface specified for 135462-01. -
Which suffixes must match when sourcing 135462-01?
Match every numeric and letter suffix in 135462-01; a similar base series does not prove interchangeability.
READY TO VERIFY YOUR PART?
Get a 135462-01 quote with price, lead time and revision check.
Trusted by 5,000+ plants worldwide | Backed by our vast inventory of top-tier control parts, drives and servo motors, fast shipments are dispatched to cover your urgent needs. ABOUT US >>
Disclaimer: Amikon Limited sells new and surplus products and develops channels for purchasing such products. Amikon Limited is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Amikon Limited is not an authorized distributor of this product, the Original Manufacturer's warranty does not apply. Amikon Limited is not an authorized distributor, dealer, or representative of the products displayed on this website. All product names, trademarks, brands, and logos used on this website are the property of their respective owners. The description, explanation, or sale of products with these names, trademarks, brands, and logos is for identification purposes only and is not intended to indicate any association with or authorization from any rights holder.
Product
Product Browsing History
- Q&A
- Policies How to order Part status information Shipping Method Return Policy Warranty Policy Payment Terms Email Marketing Policy VAT and Import Information
- Asset Recovery
- We Buy Your Equipment. Industry Cases Amikong News Technical Resources Why choose us FAQs
- Registered Address
-
32D Guomao Building, No.388, Hubin south Road, Siming district, Xiamen,Fujian, China
