-
Please try to be as accurate as possible with your search.
-
We can quote you on 1000s of specialist parts, even if they are not listed on our website.
-
We can't find any results for “”.
CABLE
Series:RX3i PacSystem
Part Number:IC695CBL001
Compatibility:PACSystems RX3i
Cable Type:Energy pack cable
Type of Input/Output:Analog
Termination Resistor:Yes
Output Module
Brand:GE Intelligent Platforms/GE Fanuc
Series:Series 90-70
Part Number:IC697MDL340
Product Type:Output Module
Rated Voltage:120 V AC
Outputs:16
DC Power:No
AC Power:Yes
LED Indicators:Yes
INPUT MODULE
IC600BF841
DISCONTINUED BY MANUFACTURER
INPUT MODULE
SERIES SIX
4POINT
ANALOG
0-10VDC
Universal analog input module
Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG600
Module Type:Universal Analog
No of Channels:Eight (8)
Number of Inputs:8 general purpose
No. of groups:Two (2)
Cold Junction Compensation:2 channels
No. of channels per group:Four (4)
Power Dissapation:5.4W max
Humidity:5 to 95%, non-condensing
Module conversion method:Sigma-delta
Module resolution:11-16 Bits
Internal Power:3.3V: 350mA; 5V: 400 mA
printed circuit board
Input Voltage: 24V DC
Operating Temperature: Typically between -30°C to +65°C
Humidity: Typically 0-95% (non-condensing)
PACSystems RX3i Power Supply module
Part Number:IC695PSD140
Product Description:Power Supply module
Input voltage range:85 to 264 VAC 100 to 300 VDC
Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation:None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps
Analog Input HART module, 8 channels single ended, 4 channels differential,channels are configurable for voltage,current and current/ HART. Supports Current: 0 to 20mA, 4 to 20mA, +/- 20mA; Voltage: +/- 10V, 0 to 10V, +/- 5V, 0 to 5V, 1 to 5V. The anal
NETWORK INTERFACE MODULE
Brand:GE Fanuc
Series:Versamax
Part Number:IC200BEM003
Description:VersaMax master module
Data:3854 input/output
Data Rate:9.6 k baud to 12 M baud
Connector:9 Pin D-sub
Bus Voltage:5 Volts
Slave Devices:125
RX3i 24VDC power supply, 40 watts.
▪+5.1 VDC output
▪ +24 VDC relay output that can be used to power circuitson Output Relay modules
▪ +3.3 VDC. This output is used internally by RX3i moduleswith IC695 catalog numbers
▪Isolation NONE
▪Ripple (all outputs) 50 mV
▪Noise (all outputs) 50 mV
SR489P5LOA20
DISCONTINUED BY MANUFACTURER
GENERATOR MANAGEMENT RELAY
PHASE CURRENT INPUTS - 5 AMP
20-60 V DC
20-48 V AC
48/62 HZ
EIGHT 4-20 MA ANALOG OUTPUTS
BASIC DISPLAY
120/240VAC, 125VDC Multipurpose Power Supply is suitable for use in load -sharing and redundancy application. It must be installed in a PACsystems RX3i (IC695catalog number) Universal Backplane. It can be used as the only power supply in the backplane
