Infi 90

IMAGING CARD

Supply Voltage:24V DC (±5%)
Power Consumption:25W (typical)
Isolation :1500V AC 
Sensor Interface:GigE Vision (2 ports)
Camera Support:Up to 8MP resolution @ 60fps
Pixel Depth:8/10/12-bit
Throughput:2.5 TOPS (INT8)

BRC400 Bridge Controller

CONTROLLER
HARMONY BRIDGE
BRC400
BUTTON CELL BATTERY
SINGLE PORT
RELAY OUTPUT

AOT 150 Analog Output Module

Output Channels: 16 single-ended
Voltage: 0-10V, ±10V
Current: 4-20mA, 0-20mA
Supply Voltage: 24V DC (±10%)
Power Consumption: 6W (typical), 8W (max)
Inrush Current: <2A for 20ms

Symphony Plus Bridge Controller Module

SPBRC410
Controller with Modbus TCP Interface
BRIDGE CONTROLLER
HARMONY RACK / SYMPHONY PLUS
W/ MODBUS TCP INTERFACE
INFI90 / BRC410 / SPBRC41000000

Digital Output Module

HARMONY BLOCK DIGITAL OUTPUT MODULE
3 AMP
24VDC
240VAC
16 OUTPUTS
FUSING/ON BOARD ELECTROMECHANICAL RELAYS
SPDT

AIN-220 Analog Input Module

Series: Harmony/800xA System
Model No.: P-HB-AIN-2200C100
Type: High-Density Analog Input Module
Voltage: ±10V, 0-10V, 1-5V
Current: 0-20mA, 4-20mA
Resolution: 16-bit (0.0015% of span)
Common Mode Rejection: >120dB @ 50/60Hz
Normal Mode Rejection: >60dB @ 50/60Hz

I/O Power Supply Module

NPCI03
I/O Power Supply Module 
24V DC power source
500V AC (input to output)
Input Voltage:5V DC  
Input Current:1.8A max
Output Voltage:24V DC (±0.5%, regulated)
Output Current:0.4A max (400 mA)
Output Power:9.6W (24V * 0.4A)
Ripple & Noise:< 50 mV peak-to-peak

Esacontrol Board

INFI 90 
SEAME08002
Esacontrol Board 
5 VA, +5 VDC
and +15 VDC

Esacontrol Board

INFI 90 
SEAM E08000
Esacontrol Board 
5 VA, +5 VDC
and +15 VDC

POWER SUPPLY

POWER SUPPLY
24 VDC OUTPUT
120/240 VAC INPUT

POWER RELAY

ODC24A
POWER RELAY
SOLID STATE
SPST-NO / 1 FORM A
18-32 VDC INPUT
60 VDC OUTPUT
3 AMP

OPTOCOUPLER MODULE

OPTOCOUPLER MODULE
ELECTRONIC INTERFACE
1 AMP
24 V
5-60 VDC
-20 TO +80 DEGREES C
DIN RAIL MOUNT

AC Output Module

OAC-24A
AC Output ModuleINFI 90
24 VDC
850 MA

PLC RACK

PLC RACK
CHASSIS
12 SLOT
19 IN
NET 90
140 VA

TERMINATION LOOP CABLE

TERMINATION LOOP CABLE
COMMUNICATION
INFI 90
6 FEET

TERMINATION LOOP CABLE

TERMINATION LOOP CABLE
INFI 90
10 FEET

ANALOG TERMINATION CABLE

ANALOG TERMINATION CABLE
300V. 22AWG
INFI 90

Boot-Terminator / Diagnostic ROM Module

Boot-Terminator 
Diagnostic ROM Module
Supply Voltage:+5V DC, +3.3V DC
Power Consumption :< 1W
Memory Type:Mask ROM or Flash ROM
Rated Voltage:300V
Rated Current:2A - 4A

MC-1 Card

L34701-A1  
MC-1 Card
Bailey Infi 90
DCS systems
Typically 24 VDC
Bailey DCS systems

Touchscreen Control Module

TOUCHSCREEN CONTROL MODULE 
FOR 90 SYSTEM IOS
Supply Voltage:Typically +24 V DC
Power Consumption:5 - 10 W
Screen Size:5.7 inches
Resolution:320 x 240 pixels

16" Industrial Color Monitor

INTECOLOR E01942-20F 
COLOR MONITOR
Supply Voltage:24 V DC (±10%)
Power Consumption:30 W
Input Signals:VGA (D-Sub 15-pin)
Screen Size:16 inches (diagonal)
Native Resolution:1280x1024 (SXGA)
Aspect Ratio:5:4
Panel Technology:TFT LCD

16" Industrial Color Monitor

INTECOLOR E01941-20F 
COLOR MONITOR
Power Supply:24 V DC (±10%)
Power Consumption:35 W (typical), <1 W (standby)
Input Voltage Range:20-30 V DC
Video Inputs:VGA (D-Sub 15-pin), DVI-D
Communication:USB for touch interface (if equipped)
Inrush Current:<20 A (at 24 V DC)

Digital Slave Input Module

DSI01
Digital Slave Input Module
Input Channels:16 points
Input Voltage:24 V DC (nominal)
Operating Range:19.2-30 V DC
ON Voltage:≥15 V DC
OFF Voltage:≤5 V DC
Input Current:≤3 mA per point (typical)
Input Impedance:7 kΩ

Digital Output Module

DO-02-16
Digital Output Module
Output Channels:16 points
Output Type:Transistor output (sink or source)
Rated Voltage:24 V DC
Operating Voltage:20-30 V DC
Max Load Current:0.5 A per channel
Max Inrush Current:2 A (100 ms)

Loop Command Controller

LOOP CONTROLLER
NET 90
LOOP COMMAND MODULE
20W
120/220 VAC
50/60 HZ