ABB Drives

Fiber Optic Repeater Module

RFO810
Up to 3 km
Supports HN800 or CW800 bus interfaces
Requires use of HBX01L/HBX01R for bus terminations
24V DC
20°C to +60°C

ACS800 R2 to R6 STO Frequency Converter

Safety Category:Category 3 (EN 954-1) 
Response Time:≤ 20 ms
Supply Voltage:24 V DC ±10%
Power Consumption:≤ 2 W
Input Signal:24 V DC (Pulse test: 0.5 Hz, 1 ms)
Input Current:6 mA per channel
Isolation Reinforced isolation : 500 V AC

Inverter Filter Plate

Rated Voltage:380–480 V AC, 3-phase (±10%)
Rated Current:100 A (at 40°C ambient)
Frequency:50/60 Hz
Leakage Current:< 5 mA (at 480 V AC)
Insulation Resistance:> 100 MΩ (500 V DC)
Dielectric Strength:3000 V AC

CONVERTER POWER BOARD

3-phase AC: 380–480 V AC
DC Bus Voltage:520–720 V DC
Power Rating:Typically 1–50 kW
Operating Temperature:-10°C to +50°C
Storage Temperature:-40°C to +85°C

CANopen Adapter Module

Product Type:CANopen Slave Interface Module
Catalog Number:160-NCAN-02C
Compatible Networks:CANopen
Power Supply:24V DC (±10%), 120 mA typical
Terminals:5-pin removable screw terminal

Circuit Board

Voltage: 24V DC
Input Impedance: 3 kΩ
Current: 0–20 mA, 4–20 mA
Resolution: 12-bit
Isolation Voltage: 2 kV AC
Altitude: ≤ 2000 m

AC drive

Output Current: 105 A
Integrated Filter: L500 
Frame Size: R7
Cooling Method: Air cooling 
Voltage:3-phase 380–480 V AC (±10%)
Frequency:47–63 Hz
 Input Current:120 A
Motor Power Range:55–75 kW 
 Apparent Power (S1):89 kVA (at 480 V)

Main Circuit Interface Card

System Voltage:24 V DC (19.2–30 V DC)
Power Consumption:≤ 1.5 W (typical)
Communication Protocol:Profibus DP-V1
Modbus RTU (via FCI module)
Isolation:Galvanic isolation between 

I/O Module Adaptor

Data Transfer Rate:Up to 12 Mbps (PROFIBUS)
Isolation Voltage:1.5 kV AC
Power Supply:24 V DC
Power Consumption:≤ 1.2 W

Drive Unit Drive Controller

Control Platform:32-bit RISC processor with FPGA logic
Control Methods:DTC , Scalar, Vector
I/O Capacity:16x DI
Operating Voltage:24 V DC (±10%)
Power Consumption:25 W (typical)
Memory:2 GB Flash (firmware/logs)
    

Controller Module

Model: KUC755AE117 / 3BHB005243R0117
Product Type: Controller Module
Power Supply Voltage: 24V DC 
Operating Temperature: 0°C to +55°C
Storage Temperature: -20°C to +70°C
Humidity: Relative humidity 5% -95%

OVERVOLTAGE MEASURING CD BOARD

UBC717AE101 
HIEE300927R0101
CIRCUIT BOARD
OVERVOLTAGE MEASURING CD BOARD

Drive Control Board

Control Methods:DTC 
Communication:Embedded
Operating Voltage:24 V DC (±10%)
Power Consumption:30 W (typical)
Memory:512 MB DDR3 RAM, 4 GB Flash

Main Control Board

DCS880
SDCS-CON-H01
Main Control Board
Operating Voltage:24 V DC (±10%)
Current Consumption:≤1.5 A
Digital I/O Channels:32 optoisolated DC I/O points
Analog I/O:±10 V DC / 4–20 mA

ACS880 AC Drive- 500V, 3PH, wall mount, regenerative

LV AC industrial wall-mounted regenerative single drive
Input Supply:3-phase 380–480V AC (±10%), 50/60 Hz
Output Power:5.5 kW (7.5 HP) @ 400V AC
Output Current:21 A continuous (40°C ambient)
Overload Capacity:110% for 60s, 150% for 2s
Output Frequency:0–500 Hz (motor-dependent)
Efficiency:>98% (at full load)
Power Factor:0.98 (min)

Terminal base

Terminal base
For AC500 V3. 1 slot for communication module. 
2 Ethernet interfaces
1 serial interface
1 CAN interface (TB5610-2ETH)

Main Control Board

Processor:PowerPC 750GL @ 400 MHz
Memory:128 MB SDRAM
Control Capacity:Up to 60,000 function blocks
Operating Voltage:5V DC
MTBF:>500,000 hours 
Mounting:AC 800M controller baseplate

Operating Panel

Display:2-line LCD with backlight
Control Keys:Navigation keys + Start/Stop/Jog buttons
Operating Voltage:24V DC 
Power Consumption:≤ 5 W

Binary Input Module

Input Channels:16x 
Input Voltage:24/48/110/125V DC
Input Threshold (ON);>60% of rated voltage
Input Current :3–8 mA
Response Time:<5 ms 
Isolation:2.5 kV AC
Power Consumption:≤ 4 W

Relay Control module

Number of Channels: 8 independent channels
Number: 6 dedicated
Contact Rating: 24 V DC / 30 mA 
Voltage: +24 V DC nominal 
Power Consumption: < 5 W

Industrial Control Module

Input Channels:16 (Grouped as 8+8)
Input Voltage:24 V DC (Nominal)
Voltage Range:19–30 V DC (Logic "1": ≥15 V)
Logic "0" Threshold:≤5 V DC
Input Current:6 mA per channel (typical)
Isolation:500 V AC (channel-to-channel)
Backplane Power :5 V DC (via P4 baseplate)

CIRCUIT BOARD

Supply Voltage:24 V DC ±10% 
Power Consumption:≤5 W
Isolation :500 V AC 
I/O Channels:Likely 8–16
Function:Fieldbus interface or signal conditioning
Status:Discontinued

CIRCUIT BOARD

Input Voltage:24 V DC ±10%
Output Voltage(s):±15 V DC or 5 V DC
Power Rating:10–20 W 
Isolation:1500 V AC
Protections:Short-circuit, over-temperature

PC BOARD

PC BOARD
PULSE TRANSFORM UNIT
RESISTIVE NETWORK
STATUS LED INDICATORS
YT204001-JB

DRIVE BOARD

DRIVE BOARD
TRIGGER PULSE
RESISTIVE NETWORK
YXU-168G