ABB

POWER SUPPLY

Input Voltage Range:85-264V AC
Input Frequency: 47-63Hz 
Input Frequency: 47-63Hz 
Output Voltage: 24V DC
Voltage Adjustment Range: 22-28V DC
Ripple & Noise: <150mV p-p (typical)
Load Regulation: ±1% (10-100% load)
Line Regulation: ±0.5% (85-264V AC)

FILTER

Rated Voltage: 250V AC
Current Rating: 5A (continuous)
Frequency Range: 50/60Hz 
Filter Type: π-type (C-L-C) filter
Common Mode Attenuation: >60dB @ 1MHz
Differential Mode Attenuation: >40dB @ 100kHz

FILTER

Rated Voltage: 250V AC
Current Rating: 5A (continuous)
Frequency Range: 50/60Hz 
Filter Type: π-type (C-L-C) filter
Common Mode Attenuation: >60dB @ 1MHz
Differential Mode Attenuation: >40dB @ 100kHz

Cross Profile

Cross Profile
62mm W, 
1m L For Use With TriLine

Industrial module

Channels:8/16 DI or DO
Input Voltage:24V DC
Output Type:Relay/Transistor
Isolation:1.5kV AC
PROFIBUS DP (via coupler)
Modbus RTU (RS-485)
EtherNet/IP (optional)

Control Board

Operating Voltage: 24V DC (±10%)
Power Consumption: <5W typical
Isolation Voltage: 1500V AC
Analog Inputs:2 channels
Digital Inputs:24V DC, optically isolated
Relay Outputs:250V AC/30V DC, 2A
PROFIBUS DP
Modbus RTU
DeviceNet

Control Module

Input Channels: 4 
Voltage: ±10V, ±5V, 0-10V, 0-5V
Current: 0-20mA, 4-20mA (with HART support)
Resistance: RTD (Pt100, Pt1000)
Thermocouple: J, K, T, E, N, R, S, B
Resolution: 16-bit (0.0015% of range)
Accuracy: ±0.05% of span (typical)
Update Rate: 50ms per channel (all channels)
Common Mode Rejection: >120dB @ 50/60Hz

Control Circuit Board

Operating Voltage: 24V DC ±10%
Power Consumption: <8W typical
Isolation Voltage: 2000V AC
Analog Inputs:0-10V/±10V/4-20mA configurable
Digital Inputs:24V DC, optically isolated
Relay Outputs:250V AC/30V DC, 5A
PROFIBUS DP
CANopen
Modbus RTU

Control Circuit Board

Power Consumption:6W typical
Isolation Voltage:2000V AC (input to output)
Analog Inputs:2 channels (0-10V/4-20mA)
Digital Inputs:6 channels (24V DC)
Relay Outputs:3 channels (250V AC/5A)
Resolution: 14-bit (analog inputs)
Sampling Rate: 10kHz (control loop)
Response Time: <2ms (digital I/O)
Accuracy: ±0.1% of full scale

Control Circuit Board

Operating Voltage: 24V DC ±10%
Power Consumption: 10W typical
Isolation Voltage: 2500V AC (input to output)
Processor: 32-bit DSP + FPGA
Control Loop Update: 62.5μs
Analog Inputs:2 channels (±10V/4-20mA)
Digital Inputs:8 channels (24V DC)
Relay Outputs:3 channels (250V AC/2A)
Encoder Interface:1 channel (HTL/TTL/SSI)

Controller Card

Processor:Dual-core ARM Cortex + FPGA
Clock Speed:800 MHz (ARM), 200 MHz (FPGA)
Memory:512 MB DDR3 RAM
Operating Voltage:24V DC ±10%
Power Consumption:5W (max)
Isolation :2500V AC
Analog Inputs:4 ch (16-bit, ±10V/4-20mA)
Digital Inputs:12 ch (24V DC, 3ms debounce)
Relay Outputs:4 ch (250V AC/5A)
Encoder:2 ch (HTL/TTL/SSI/EnDat 2.2)

Controller Card

Operating Voltage: 24V DC ±10%
Power Consumption: 18W
Control Loop Speed: 31.25μs
Positioning Accuracy: ±1 encoder count
Velocity Ripple: <0.01% of rated speed
Synchronization Jitter: <100ns between axes
Analog Inputs:6 ch (16-bit, ±10V/4-20mA, 50kHz)
Digital Inputs:16 ch (24V DC, <100μs response)
Relay Outputs:6 ch (250V AC/5A, 30V DC/5A)
Encoder Inputs:3 ch (Differential RS422, 20MHz)
PTC/KTY Inputs:4 ch (Motor temp sensors)

PC BOARD

PC BOARD
PWA SMI
16 MHZ SENSOR
PWA, SENSOR MICRO-101

IGBT Module

Collector-Emitter Voltage (Vces):1200V
Collector Current (Ic @ 25°C):450A
Collector Current (Ic @ 80°C):300A
Pulse Current (Icm):900A
Power Dissipation (Ptot):1800W
Gate-Emitter Voltage (Vges):±20V
Turn-on Delay Time (tdon):110ns
Rise Time (tr):50ns
Turn-off Delay Time (tdoff):400ns
Fall Time (tf):120ns
Switching Frequency:Up to 20kHz

Bus Coupler

Supply Voltage: 24V DC (19.2-30V DC)
Power Consumption: 1.5W 
Current Capacity: 6A 
Isolation Voltage: 500V AC 
Fieldbus Protocol:PROFIBUS DP-V1
Data Rate:Up to 12 Mbps
Address Range:1-125 (PROFIBUS)
I/O Connection:S800 I/O bus

TEMP MEASURING BOARD

Input Channels:4 or 8 (isolated)
Supported Sensors:PT100/PT1000, TC (J/K/T/E), 0-20mA, ±10V
Measurement Accuracy:±0.1% FS (RTD), ±1°C (TC)
Resolution:0.01°C (RTD), 0.1°C (TC)
Update Rate:100ms per channel
Isolation:1500V AC 
Power Supply: 24V DC (±10%) via backplane
Power Consumption: <3W
Input Impedance: >1MΩ 
Max. Input Voltage: ±15V

Gate Circuit Board

DRIVE
IGBT
BOARD KIT
Modbus TCP/IP
-20°C to 60°C (-4°F to 140°F)
Number of Inputs: 16
Number of Outputs: 16

07KT98 Advant Controller 31 Basic Unit

Microprocessor-based protection
Three-phase trip-free mechanism
Front-connected auxiliary contacts
Integrated earth fault protection
Remote control and monitoring capabilities
High-performance AC800F platform
Supports a wide range of I/O modules
Supports a variety of programming languages
Suitable for a wide range of industrial applications
Compact and modular design

Frequency Converter Driver Board

Voltage Input: 380V to 690V AC (3-phase) 
Switching Frequency: 2–16 kHz range
Operating Temperature: -10°C to +50°C (ambient, typical)
Humidity: ≤95% non-condensing

Power Supply

Input Voltage Range: 85-264V AC (universal input)
Input Frequency: 47-63Hz
Inrush Current: <25A (at 115V AC), <50A (at 230V AC)
Power Factor: >0.95 (at full load)
Efficiency: 92% typical
Output Voltage: 24V DC
Output Current: 6A continuous
Current Limit: 7.5A 
Ripple & Noise: <150mV p-p 
Load Regulation: ±0.5% (10-100% load)
Line Regulation: ±0.2% (85-264V AC)

BRC400 Bridge Controller

CONTROLLER
HARMONY BRIDGE
BRC400
BUTTON CELL BATTERY
SINGLE PORT
RELAY OUTPUT

Servo Control Board

Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs

PC BOARD

JINTC1C
PC BOARD
PCB FOR ACS850-04-035A-5+E200+J400
ACS880 SERIES

DC drive motherboard

Memory:32MB SDRAM
Control Loop Time:100μs (speed)
Digital I/O:12x 24V DC inputs
Supply Voltage:24V DC ±10%
Power Consumption:15W max
Isolation :2500V AC 

Control Board

Clock Speed:150MHz (DSP), 100MHz (FPGA)
Memory:512kB Flash, 68kB SRAM
Operating Voltage:24V DC ±10%
Power Consumption:12W typical
Isolation:2500V AC
Control Loop Update: 62.5μs (speed)
Analog Inputs:2 ch (16-bit, ±10V/4-20mA)
Digital Inputs:6 ch (24V DC, 3ms filter)
Relay Outputs:3 ch (250V AC/5A)
PTC Input:2 ch (Motor temp sensors)