ABB

Touch screen

2x Ethernet 10/100Mbit
1x RS-232/-422/-485
2x USB 2.0 Host
1x SD-card slot
2x Expansion slot
Storage capacity user data: 256 MB
Storage type user data: Flash Disk
Storage type user program: DDR RAM
Power consumption (@Pcons): 24 W
Power supply: 24 (18 ... 30) V DC
Screen colors: 64k colors

GATE DRIVE BOARD

Voltage Rating:1700 V
Current Drive Capability:up to 10A or higher
Gate Drive Output:15V
Peak Output Drive Current: Up to 10A
Operating Temperature:  -40°C to +85°C

IMAGING CARD

Supply Voltage:24V DC (±5%)
Power Consumption:25W (typical)
Isolation :1500V AC 
Sensor Interface:GigE Vision (2 ports)
Camera Support:Up to 8MP resolution @ 60fps
Pixel Depth:8/10/12-bit
Throughput:2.5 TOPS (INT8)

Control Unit

Processor: Dual-core 32-bit RISC processor
Clock Speed: 800 MHz
Ethernet:4× 10/100/1000 Mbps (RJ45)
Serial:2× RS-485 (Modbus RTU)
IEC 61850:MMS, GOOSE, SV (Class 1)
Fieldbus:PROFIBUS DP-V1 (optional)
Power Supply: 48-250V DC or 100-240V AC
Power Consumption: 15W (typical)
Isolation: 4kV AC

Charging controllers

Input Voltage:380-480V AC, 3-phase (±10%)
Output Voltage:115 V AC or 230 V AC  ±10%, 50/60 Hz
Current Rating:20A (continuous), 30A (peak)
Efficiency:>94% (at full load)
Power Factor:>0.98 (at full load)
Overvoltage:+15% of setpoint
Overcurrent:110% for 60min
Reverse Polarity:Instant cutoff
Short Circuit:<1ms response

Servo Motor

Rated Power:4.5 kW
Rated Torque:28 Nm
Peak Torque:84 Nm (300% overload)
Rated Speed:1500 rpm
Max Speed:5000 rpm
Voltage:400V AC (3-phase)
Current:9.5A (rated), 28A (peak)
Torque Constant:1.8 Nm/A
Back EMF:110 V/krpm
Rotor Inertia:0.012 kg·m²
Stator Resistance:0.8 Ω (line-to-line)
Thermal Time Constant:45 minutes

REF542plus HMI Unit

Supply Voltage:24V DC (18-36V range)
Power Consumption:8W (typical)
Isolation :2kV AC 
Display Type:5.7" TFT LCD (color)
Resolution:320 × 240 pixels
Touch Panel:Resistive (single-touch)
Backlight:LED (50,000h lifespan)
Ethernet:10/100 Mbps (IEC 61850 MMS)
Optical Port: IR interface for local config
USB:Type B

Multi flame detector - control unit

Power Supply:120-220 Vac +/- 20%, 
45-65 Hz 24Vdc +/- 20%
AC input: 30 VA (6A / 5 ms inrush current)
DC input: 22 W (24A / 2 ms inrush current)
Operating: 0 - 60°C (32 - 140°F)
Storage: -25 - 85°C (-13 - 185°F)
Contact rating: 250 Vac 3 A 750 VA cosΦ 0.4
220 Vdc 300 mA 66 W

16 Bit Profibus DP Adapter Module

Up to 12 Mbps.
Auto-detection of baud rate
Address Range: Configurable from 0 to 126
Supply Voltage: 24 VDC ±10%.
Power Consumption: < 2 W
Operating Temperature: -10°C to +55°C.
Storage Temperature: -40°C to +70°C

CONTROL CIRCUIT BOARD

Input Voltage: +5V, +12V
Current Consumption: Typically under 2A
RS-232/RS-485
Operating Temperature: 0°C to 50°C.
Storage Temperature: -20°C to 70°C.
Relative Humidity: 5% to 85% (non-condensing)

Traction Voltage Sensors

Nominal primary voltage:2000V r.m.s
Measuring range:±3000
Primary turn number:20000
Secondary turn number:2000
Secondary current at UPN:50
Accuracy at UPN:≤±1
Offset current:≤±0.3
Linearity:≤±0.1
Thermal drift coefficient:-25 … +70°C ≤±5 

Power Supply Rack

Overvoltage:28V DC
Input Voltage:400-480V AC, 3-phase (±10%)
Output Voltage:24V DC regulated
Output Current:50A (continuous), 60A (peak)
Power Rating:1.2kW (per module)
Efficiency:>93% (at 50% load)
Power Factor:>0.95

70 AS 47b-E Module

Power Supply: 24V DC (±10%)
Power Consumption: 3.5W (typical)
Number of Channels: 8
Current Output Range: 4-20mA
Voltage Output Range: 0-10V
Resolution: 16-bit
Accuracy: ±0.1% of span
Current: ≤750Ω
Voltage: ≥1kΩ

Diode Module

Input Voltage:24V DC nominal
Input Current:3-8mA per channel 
Isolation:1500V AC (field to logic)
Response Time:<1ms (ON/OFF)
Number of Channels:32 
Voltage Rating:1600V (V_RRM)
Current Rating:300A (I_FAVM)
Surge Current:8kA (I_FSM, 10ms)
Forward Voltage:1.25V @ 300A (typical)

Miniature Circuit Breaker

AC: 230/400 V
DC: 60 V
Rated Current (Iₙ): 42 A
Rated Insulation Voltage (Ui): 500 V
Rated Impulse Withstand Voltage (Uimp): 6 kV

Rotational ac motor M10

Rated Output:1.8 kW 
Peak Torque:180 Nm (transient, 1 sec)
Rated Torque:60 Nm (continuous)
Rated Speed:1,500 rpm
Max Speed:3,000 rpm
Voltage Rating:400 V AC (3-phase)
Current Rating:4.2 A (RMS, continuous) / 12.5 A (peak)
Feedback Device:Resolver (multispeed, 1x/4x)

Interface Module

Range: Typically 4-20 mA
Input Impedance:≤ 10 Ω
Load Capacity: Standard 0-500 Ω
Voltage: 24 V DC 
Test Voltage: Typically 1.5 kV AC
Typical: ±0.1% of full scale 

Communication Module

Communication Interface:RS-232, RS-485
Data Transfer Speed:Up to 115,200 bps
Power Supply:24V DC
Mounting Type:DIN rail mounted
Operating Temperature:-20°C to 60°C (-4°F to 140°F)
Storage Temperature:-40°C to 85°C (-40°F to 185°F)
Humidity Tolerance:5% to 95% non-condensing

Power Interface Module

Voltage: 125 VDC Nominal 
Power Consumption: Typically < 5W
Input-to-Input: 1500 VAC min.
Input-to-Output/Logic: 1500 VAC min.
Output-to-Output: 500 VAC min.
Output/Logic-to-S+ I/O: 500 VAC min

Rigi Crowbar Drive PCB

Power Supply:24V
Operating Temperature Range
Typically -20°C to +60°C
Storage Temperature Range
-40°C to +85°C

AUTOMATIC TRANSFER SWITCH DEVICE

Rated Voltage:400 V AC (3-phase, 4-wire)
Rated Current:22 A (continuous)
Rated Frequency:50/60 Hz
Transfer Time:< 100 ms (typical for open transition)
Withstand Current:10 kA (IEC 60947-6-1)
Mechanical Life:10,000 cycles (minimum)

Terminal Board

Number of Positions:10 Position
Pitch:9.53 mm
Current Rating:30 A
Voltage Rating:300 V
Wire Gauge Min:22 AWG
Wire Gauge Max:14 AWG
Type:Terminal Block
Number of Rows: 2 Row
Mounting Style:Panel Mount

Rack Mounted

Protocol: PROFIBUS DP-V0
Data Transfer Rates:up to 12 Mbp
Connector Type: 9-pin D-sub
Electrical Interface: RS-485
Voltage: +5 V DC 
Power Consumption: 1-2 W
Max. Input Data (to Master): Up to 244 bytes per cycle
Max. Output Data (from Master): Up to 244 bytes per cycle

Rack Mounted

Protocol: PROFIBUS DP-V0
Data Transfer Rates:up to 12 Mbp
Connector Type: 9-pin D-sub
Electrical Interface: RS-485
Voltage: +5 V DC 
Power Consumption: 1-2 W
Max. Input Data (to Master): Up to 244 bytes per cycle
Max. Output Data (from Master): Up to 244 bytes per cycle

Programmable Logic Controller (PLC) module

CPU Type: 32-bit RISC-based processor
Clock Speed: 100–200 MHz 
Program Memory: Up to 4 MB Flash
Data Memory: Up to 2 MB RAM 
Execution Speed: 0.1 ms
Input Voltage: 24V DC
Resolution: 12-bit to 16-bit