








Intrinsically Safe Wireless AccessPoint/Bridge
Tri-Band operation
Convert Ethernet device to wireless
Zone 1, Division 1 mountable
Rapid roaming
10/100Mbs Ethernet
ATEX / IECEx certified
FM / FMC approved
Wide temp. range –40°C to +60°C
PoEx™ Power over IS Ethernet option
Copper to Fibre Intrinsically Safe Converter
Copper to Fibre Optic Converter
10/100Mbps wire speed
Extend up to 5km (10Mbs)
Zone 1, Division 1 mountable in suitableenclosure
Transparent operation
Choice of fibre optic connection styles
ATEX / IECEx certified
FM / FMC approved
Wide temp. range –40°C to +70°C
PoEx™ Power over IS Ethernet option
Intrinsically Safe ManagedEthernet Switch
5-port 10/100Mbps links
Zone 1, Division 1 mountable insuitable enclosure
Broadcast “storm” protection
Intelligent Routing
Programmable Management
ATEX / IECEx certified
FM / FMC approved
Wide temp. range –40°C to +70°C
Half/Full Duplex
Power source for PoEx™ Power overIS Ethernet
Status LEDs to show activity
POEX INTRINSICALLY SAFE ETHERNET
Zone 2 mountable for connections toZone 0 and 1
Galvanically isolated RJ45 ports
Transparent operation
Compact alternative solution to
fibreoptics and media converters
ATEX / IECEx certified
FM / FMC approved
Wide temp. range –40°C to +70°C
Single 20–30V DC power supply
Status LEDs to show activity
Bus interface module
PROFIBUS BIM
BUS INTERFACE MODULE
LAN TO RAILBUS TO POWER SUPPY: 500 V
244 BYTES MAX
RAILBUS 12 V CURRENT 420 MA
POWER SUPPLY
POWER SUPPLY
2.9 TO 4.9 AMP
18-36 VDC
-40 TO +70 DEGREES C
Product type : System power supply
Universal Safe IO IS Interfaces Module
USIO 16CH AI/AO/DI/DO FTA CC
Input Voltage: 24 V DC
Operating Temperature Range:
-40°C to +70°C (-40°F to +158°F)
Certification: Ex ia IIC T4
Bus Interface Module
Product No.: 8502-BI-DP
Product Type: Bus Interface Module (BIM)
Protocol: Profibus
Function: Links MTL8000
node to Profibus-DP host LAN
I/O Support: Supports up to 24 I/O modules
Diagnostics: Extended diagnostics
for module and channel status
LAN Speed: Up to 6 Mbaud
Memory: Non-volatile memory for configuration
ANALOG INPUT MODULE
8 single-ended 4-20 mA input channels
Non-incendive field circuits
HART pass-through
HART variable and status reporting
2- or 4-wire transmitters
Open and short circuit detection
24 V dc bussed field power required

Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.