Operating Temperature 0° to 50° C
Storage Temperature -20° to 80° C
Operating Humidity 5 to 95% (non-condensing)
Air Composition No corrosive gases permitted
Power Budget Requirements 5 VA @ 8--30 VDC
Fuse (external) 10 A time-lag (T)
Buffer for date/time Gold capacitor
Temperature class T4 (Zone 2)
Operating temperature 0 °C...+60 °C
Storage temperature -40 °C...+85 °C
Processor Atom E3815 1.46 GHz
Main 256 MB with ECC
Static RAM 2 MB with ECC
backed up by battery
1 GB on-boad flash memory
SDHC (4 to 32 GB) Class 10
D-sub 9 pins, male (*2)
Full/Half duplex (software settings)
Synchronisation Asynchronous
Operation 0° to 55°C
Transportation/storage 40° to 85°C (*1)
Dust 0.3 mg/m3 or less
Resistance to corrosive gases
ANSI/ISA S71.04 Class G2 (Standard)
(ANSI/ISA S71.04 Class G3, option)
Resistance to vibration
0.15 mm P-P (5 to 58 Hz), 1 G (58 to 150 Hz)
Resistance to shock
15 G, 11 ms
(during power-off, for sine half-waves in XYZ-directions)
Altitude 2000 m or less
High-performance
high-elibility modular controller
Memory with ECC
Low heat dissipation eliminates the need for a fan
Awealth of RAS features -CPU self-diagnostics
temperature monitoring. 1/0 diagnostics, and more
power supply module, local bus (SB bus)
and control network can all be duplexed
and all modules are hot-swappable
Can function as link active schedulers
(L ASs) for low-speed voltage mode (H1)
FOUNDATION Fieldbus segments
and link up FOUNDATION Fieldbus-enabled feld devices
Processor Atom E3815 1.46 GHz
Main 256 MB with ECC
Static RAM 2 MB with ECC
backed up by battery
1 GB on-boad flash memory
SDHC (4 to 32 GB) Class 10
D-sub 9 pins, male (*2)
Full/Half duplex (software settings)
Synchronisation Asynchronous
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
MC68030 at 25 MHz with MMU
MC68882 at 25 MHz
Data and Instruction, each 256 KByte
On-board via the FGA-002B
16 MByte DRAM with Byte Parity
4 MByte, 32-bit
An electronic converter used
in combination with the VITO probes
HART® communication to tank gauging ATG *2
ATEX KEMA 01ATEX1212
IECEx KEM 05.0014
Kosha certificate; 13-AV4BO-0487
FM I. D. 3015746
CSA certificate 1635480
Nominal Voltage 24 VDC
Type Control Module
Output Signals 32, commoned
Voltage Range 16-32 VDC
Maximum Voltage 36 VDC
Voltage Drop < 2.8 VDC @ 1.7A, typical
Power Module Load < 13 watts
MPC8240 32-bit microprocessor
L1 cache—16KB/16KB MPC60x class
32MB of on-board SDRAM
with optional ECCprotection
Two 32-pin PLCC/CLCC sockets for Flash memory;
upto 1MB capacity for on-board firmware
or userspecified requirements
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
