ALL MANUFACTURERS

Control Circuit Board

Operating Voltage: 24V DC ±10%
Power Consumption: 10W typical
Isolation Voltage: 2500V AC (input to output)
Processor: 32-bit DSP + FPGA
Control Loop Update: 62.5μs
Analog Inputs:2 channels (±10V/4-20mA)
Digital Inputs:8 channels (24V DC)
Relay Outputs:3 channels (250V AC/2A)
Encoder Interface:1 channel (HTL/TTL/SSI)

Controller Card

Processor:Dual-core ARM Cortex + FPGA
Clock Speed:800 MHz (ARM), 200 MHz (FPGA)
Memory:512 MB DDR3 RAM
Operating Voltage:24V DC ±10%
Power Consumption:5W (max)
Isolation :2500V AC
Analog Inputs:4 ch (16-bit, ±10V/4-20mA)
Digital Inputs:12 ch (24V DC, 3ms debounce)
Relay Outputs:4 ch (250V AC/5A)
Encoder:2 ch (HTL/TTL/SSI/EnDat 2.2)

Controller Card

Operating Voltage: 24V DC ±10%
Power Consumption: 18W
Control Loop Speed: 31.25μs
Positioning Accuracy: ±1 encoder count
Velocity Ripple: <0.01% of rated speed
Synchronization Jitter: <100ns between axes
Analog Inputs:6 ch (16-bit, ±10V/4-20mA, 50kHz)
Digital Inputs:16 ch (24V DC, <100μs response)
Relay Outputs:6 ch (250V AC/5A, 30V DC/5A)
Encoder Inputs:3 ch (Differential RS422, 20MHz)
PTC/KTY Inputs:4 ch (Motor temp sensors)

PC BOARD

PC BOARD
PWA SMI
16 MHZ SENSOR
PWA, SENSOR MICRO-101

IGBT Module

Collector-Emitter Voltage (Vces):1200V
Collector Current (Ic @ 25°C):450A
Collector Current (Ic @ 80°C):300A
Pulse Current (Icm):900A
Power Dissipation (Ptot):1800W
Gate-Emitter Voltage (Vges):±20V
Turn-on Delay Time (tdon):110ns
Rise Time (tr):50ns
Turn-off Delay Time (tdoff):400ns
Fall Time (tf):120ns
Switching Frequency:Up to 20kHz

Bus Coupler

Supply Voltage: 24V DC (19.2-30V DC)
Power Consumption: 1.5W 
Current Capacity: 6A 
Isolation Voltage: 500V AC 
Fieldbus Protocol:PROFIBUS DP-V1
Data Rate:Up to 12 Mbps
Address Range:1-125 (PROFIBUS)
I/O Connection:S800 I/O bus

Analog Input Module

Analog Input IOTA N
on-Redundant
Circuits: 16
Size: 6"

TEMP MEASURING BOARD

Input Channels:4 or 8 (isolated)
Supported Sensors:PT100/PT1000, TC (J/K/T/E), 0-20mA, ±10V
Measurement Accuracy:±0.1% FS (RTD), ±1°C (TC)
Resolution:0.01°C (RTD), 0.1°C (TC)
Update Rate:100ms per channel
Isolation:1500V AC 
Power Supply: 24V DC (±10%) via backplane
Power Consumption: <3W
Input Impedance: >1MΩ 
Max. Input Voltage: ±15V

Gate Circuit Board

DRIVE
IGBT
BOARD KIT
Modbus TCP/IP
-20°C to 60°C (-4°F to 140°F)
Number of Inputs: 16
Number of Outputs: 16

07KT98 Advant Controller 31 Basic Unit

Microprocessor-based protection
Three-phase trip-free mechanism
Front-connected auxiliary contacts
Integrated earth fault protection
Remote control and monitoring capabilities
High-performance AC800F platform
Supports a wide range of I/O modules
Supports a variety of programming languages
Suitable for a wide range of industrial applications
Compact and modular design

Chassis for redundant I/O modules (conformal coated)

Frequency Converter Driver Board

Voltage Input: 380V to 690V AC (3-phase) 
Switching Frequency: 2–16 kHz range
Operating Temperature: -10°C to +50°C (ambient, typical)
Humidity: ≤95% non-condensing

Power Supply High Density Module

Chassis Type:Main/Expansion/RXM
Nominal Voltage:24 VDC
Input VAC @ 47-63 Hz:n/a
Input VDC:22-31
Fuse Rating and Type:15 amps, time-delay
Output Hold Time:2.8 ms minimum
Diagnostic Indicators:PASS, FAULT, ALARM, TEMP,BAT LOW

Power Supply

Input Voltage Range: 85-264V AC (universal input)
Input Frequency: 47-63Hz
Inrush Current: <25A (at 115V AC), <50A (at 230V AC)
Power Factor: >0.95 (at full load)
Efficiency: 92% typical
Output Voltage: 24V DC
Output Current: 6A continuous
Current Limit: 7.5A 
Ripple & Noise: <150mV p-p 
Load Regulation: ±0.5% (10-100% load)
Line Regulation: ±0.2% (85-264V AC)

High Density Main Chassis

8111
CHASSIS
POWER SUPPLY RACK
NO CARDS INSTALLED

BRC400 Bridge Controller

CONTROLLER
HARMONY BRIDGE
BRC400
BUTTON CELL BATTERY
SINGLE PORT
RELAY OUTPUT

Servo Control Board

Memory:64MB DDR3, 16MB Flash
Operating Voltage:24V DC ±10%
Power Consumption:15W typical
Control Loop :62.5μs update rate
Position Resolution:24-bit (0.0001°)
Velocity Ripple:<0.02% of rated speed
Torque Control:±0.5% of rated torque
Motor Outputs:3-phase PWM (up to 20kHz)
Encoder Inputs:2x EnDat 2.2/SSI (26-bit)
Digital I/O:8x 24V DC inputs, 4x 0.5A outputs

PC BOARD

JINTC1C
PC BOARD
PCB FOR ACS850-04-035A-5+E200+J400
ACS880 SERIES