ALL MANUFACTURERS

STRATEGIC LOOP CONTROLLER

CONTROLLER
SINGLE LOOP
120/240 VAC
24 VDC
19 WATT

Smart Interface Unit

SIU010
Smart Interface Unit 
24V DC (±20%)
Power Consumption "5W
Protocol PROFIBUS DP-V0/V1
9.6 kbps to 12 Mbps (auto-sensing)

Esacontrol Board

INFI 90 
SEAME08002
Esacontrol Board 
5 VA, +5 VDC
and +15 VDC

Esacontrol Board

INFI 90 
SEAM E08000
Esacontrol Board 
5 VA, +5 VDC
and +15 VDC

POWER SUPPLY

POWER SUPPLY
24 VDC OUTPUT
120/240 VAC INPUT

POWER RELAY

ODC24A
POWER RELAY
SOLID STATE
SPST-NO / 1 FORM A
18-32 VDC INPUT
60 VDC OUTPUT
3 AMP

OPTOCOUPLER MODULE

OPTOCOUPLER MODULE
ELECTRONIC INTERFACE
1 AMP
24 V
5-60 VDC
-20 TO +80 DEGREES C
DIN RAIL MOUNT

AC Output Module

OAC-24A
AC Output ModuleINFI 90
24 VDC
850 MA

AC Output Module

I/O MODULE
DIN-RAIL MOUNT
HIGH DENSITY
12-140 VAC

PLC RACK

PLC RACK
CHASSIS
12 SLOT
19 IN
NET 90
140 VA

TERMINATION LOOP CABLE

TERMINATION LOOP CABLE
COMMUNICATION
INFI 90
6 FEET

TERMINATION LOOP CABLE

TERMINATION LOOP CABLE
INFI 90
10 FEET

ANALOG TERMINATION CABLE

ANALOG TERMINATION CABLE
300V. 22AWG
INFI 90

Boot-Terminator / Diagnostic ROM Module

Boot-Terminator 
Diagnostic ROM Module
Supply Voltage:+5V DC, +3.3V DC
Power Consumption :< 1W
Memory Type:Mask ROM or Flash ROM
Rated Voltage:300V
Rated Current:2A - 4A

MC-1 Card

L34701-A1  
MC-1 Card
Bailey Infi 90
DCS systems
Typically 24 VDC
Bailey DCS systems

SSI Card PCB Circuit Board

INPUT CARD 
SSI 24VDC
100 kHz to 1 MHz
24V DC (Nominal)
< 200 mA

Current Buffer

4-20 mA 
±0.1% of full-scale value
Up to 600 Ω
<10 ms
Signal isolation
amplification
and distribution in current loop systems

Pulser

Pulser Unit
Square wave signal
5V to 24V DC
Up to 10 kHz
TTL or RS-422 compatible output
High-precision pulse generation 
with ±0.1% tolerance

E/I Converter

Input Signal:Voltage: 0-5V, 0-10V
Input Impedance:≥ 100 kΩ
Output Signal:Current: 0-20mA, 4-20mA
Output Load;0–850 Ω (for 20mA max)
Power Supply:20-30V DC (typical)
Power Consumption:< 1.5W (typical)
Accuracy:±0.1% of span (typical @ 25°C)

E/I Converter

Input Signal: 0-10 V DC 
(configurable depending on system requirements)
Output Signal: Standard 4-20 mA current loop
Accuracy: ±0.1% of full-scale value
Load Impedance: 0-600 Ω for 
current loop compatibility
Response Time: <10 ms

Transfer Relay Delay

Contact Configuration:
1 NO (Normally Open)
1 NC (Normally Closed)
Contact Rating:
AC: 250V AC, 10A (resistive)
DC: 24V DC, 10A (resistive)
Coil Voltage: 24V DC (Nominal)

Transfer Relay

AC: 250V AC, 10A 
DC: 24V DC, 10A 
Coil Voltage: 24V DC (Nominal)
Contact Material: Silver alloy for 
low contact resistance and enhanced durability
Switching Time: <10 ms 
Mechanical Life: 10 million operations
Electrical Life: 100,000 operations at rated load

Signal Monitor

Voltage: 24-240V AC/DC
Current: 0.1-5A AC 
Typically ≤ 1 ms 
Frequency:50/60 Hz (±10%) 
Contact Rating:5-8A @ 250V AC 
Power Consumption:< 3 VA

Signal Monitor

Voltage: 24-240V AC/DC
Current: 0.1-5A AC
Frequency:50/60 Hz (±10%)
Contact Rating:5-8A @ 250V AC
Isolation Voltage:2500V AC
Power Consumption:< 3 VA (typical)

118VAC Auxiliary Relay

Coil Voltage:118V AC (50/60 Hz)
Operate Voltage:80% of nominal voltage
Release Voltage:20% of nominal voltage
Coil Power Consumption: 2.2 VA
Operate Time:< 20 ms
Release Time:< 15 ms
Mechanical Life:10 x 10⁶ operations