










INPUT TERMINATION BOARD
DS200TBQBG1ACB
DISCONTINUED BY MANUFACTURER
PC BOARD SDCC MARK V SYSTEM
TERMINAL BOARD R-S-T ANALOG 78WAY
DS200TBCAG1AAB
DISCONTINUED BY MANUFACTURER
PC BOARD
TRANSITION MODULE
RTD INPUT
ANALOG
Terminal Digital Connector Board
Series Mark V
Part Number DS200DTBBG1ABB
Product Type Contact Input Expansion Termination Module
Revision Quantity 3 Revisions
Backwards-Compatibility 1st two revisions
Mark V Series Grouping Group 1
DS200DTBAG1AAA
DISCONTINUED BY MANUFACTURER
DIGITAL INPUT TERMINAL BOARD
PC BOARD SDCC MARK V SYSTEM
PC BOARD
DS200TCEAG1B
DISCONTINUED BY MANUFACTURER
PC BOARD
EMERGENCY OVERSPEED BOARD
MARK V
DS200DTBCG1AAA
DISCONTINUED BY MANUFACTURER
PC BOARD
SDCC MARK V SYSTEM
ANALOG I/O CONTROL CARD
TERMINATION BOARD
FOR RELAY/SOLENOID OUTS
Excitation Amplifier Module
IS200EXAMG1AAB
EX2100
Excitation Amplifier Module
Bridge and Protection Module
Exciter PT/CT Board
IS200EPCTG1AAA
Mark VI
EX2100 series
0-10 V or 4-20 mA
Input/Output Terminal Board
RX7i 17 Slot Rack Wall (Rear) Mount
Brand:GE Fanuc
Series:Rx7i PACsystem
Part Number:IC698CHS017
Description:I/O Rack
Application:Rx7i System
I/O Capacity:17 Slots
Fan Assembly:Optional
Mounting Type:Rear Mounting
Power Supply module
Series:Series 90-70
Manufacturer:GE Fanuc
Part Number:IC697PWR710
Product Description:Power Supply module
Input Power:90 Watts at full load
Input half cycle peak inrush:3 A, typical
Input Power:90 Watts, maximum
Output Power:56 Watts, maximum
Power factor:> .95
Output Power:56 Watts
DC Output:5VDC up to 11 Amps
Output voltage, nominal:5.1 VDC
Location on Baseplates:Leftmost Slot
Mounting location:Leftmost Slot
Output voltage, range:4.90 - 5.25 VDC
Overcurrent protection:12 A, typical
Protection Type:Fuses
Ride through time:21 ms
DISCRETE INPUT MODULE
Brand:GE Fanuc
Series:Series 90-70
Part Number:IC697MDL654
Rated voltage:48 Volts DC
Input current:4.7 milliAmps
Input voltage range:-3 to 56 Volts DC
Required current:0.3 Amps
Number of inputs per module:32
Isolation voltage:1500 Volts
High-Speed Counter
Series:Series 90-70
Manufacturer:GE Fanuc (Former); Emerson Automation (Current)
Part Number:IC697HSC700
Product Description:High-Speed Counter (HSC) module
Product Type:High-Speed Counter
Processing speed:200 KHz
Input Voltage:5 VDC; 10-30 VDC
Input Voltage Range:10-30 V DC
Output protection:Short circuit protection
Output Voltage:30 V DC
Maximum count rate:up to 200 kHz
Input/Output Type:Positive Logic
Current draw:250 mA at 5VDC
Number of Inputs:12 single-ended
Power Consumption:500 milliamps at 5 V DC
RX3i Mid range controller
IC695CPE310
2 SLOT CPU
1.1 GHZ PROCESSOR
10MG MEMORY
1 RS-232 PORT
1 RS- 485 PORT
1 ETHERNET PORT

Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.