ABB

Analog Input Terminal Board

Model: NTRO12-A
Type: Analog Input Terminal Unit
Signal Type: High-Level Analog Signals
Number of Channels: 12
Product Type: Module_Termination_Unit

Analog Input Terminal Board

Model: NTAI05-A
Type: C
Number of Channels: 16 Channels
Signal Type: High-Level Analog Signals
Product Type: Module Termination Unit

ACS800 R2 to R6 STO Frequency Converter

Safety Category:Category 3 (EN 954-1) 
Response Time:≤ 20 ms
Supply Voltage:24 V DC ±10%
Power Consumption:≤ 2 W
Input Signal:24 V DC (Pulse test: 0.5 Hz, 1 ms)
Input Current:6 mA per channel
Isolation Reinforced isolation : 500 V AC

IGCT Module

Blocking Voltage 4500 V DC
Reverse Voltage:30 V 
Max RMS Current:4000 A
Peak Surge Current :32 kA
Turn-On Time: ≤ 3 µs
Turn-Off Time: ≤ 5 µs
Switching Loss: ≤ 15 kJ/s at 500 Hz

Inverter Filter Plate

Rated Voltage:380–480 V AC, 3-phase (±10%)
Rated Current:100 A (at 40°C ambient)
Frequency:50/60 Hz
Leakage Current:< 5 mA (at 480 V AC)
Insulation Resistance:> 100 MΩ (500 V DC)
Dielectric Strength:3000 V AC

CONVERTER POWER BOARD

3-phase AC: 380–480 V AC
DC Bus Voltage:520–720 V DC
Power Rating:Typically 1–50 kW
Operating Temperature:-10°C to +50°C
Storage Temperature:-40°C to +85°C

CANopen Adapter Module

Product Type:CANopen Slave Interface Module
Catalog Number:160-NCAN-02C
Compatible Networks:CANopen
Power Supply:24V DC (±10%), 120 mA typical
Terminals:5-pin removable screw terminal

Memory Board 8MB

Memory Type:Fast Page Mod
Battery Backup:Integrated 3.6V Lithium Battery 
Capacity:8 MB SDRAM
Data Retention:≥72 hours 
Interface:96-pin DIN 41612 connector (Type C)

Communication Module

Order Code:3BHE019958R0101
Functional Designation:UA D206 A
Power Supply:5 V DC
Consumption: 500 mA (max)
Data Rate:300 bps – 115.2 kbps (per port)
Isolation:500 V AC 

Interface Module

Signal Channels:16 single-ended analog inputs
 Voltage: ±10V, ±5V, ±1V, 0–10V
Current: 4–20mA, 0–20mA 
Resolution:16-bit (including sign bit)
Accuracy:±0.05% of full scale (25°C)
Sampling Rate:10 ms/channel 
Input Impedance:>1 MΩ
Overvoltage Protection:±30V continuous
Common-Mode Rejection:>120 dB at 50/60 Hz

Control Board

Clock Speed 800 MHz
Memory:128 MB NOR Flash 
Backplane Interface:PCI-104
Power Requirements:5V DC @ 3.5A
Vibration: 5g @ 10–500Hz

Millmate Controller

Processor: 1.2 GHz 
Power Supply: 24V DC ±10%
Power Consumption: 120W
MTBF: >200,000 hours
Control Loop Speed: 0.5–5 ms (configurable)
Max I/O Points: 5,000 digital / 2,000 analog

Communication Module

Supply Voltage: 5V DC
Power Consumption: 1.2A @ 5V DC (6W)
2× RS-485 ports (9-pin D-sub male).
Baud Rate: 9.6 kbps to 12 Mbps (auto-detect)
Max Stations: 125 slaves per segment
Redundancy Switchover: < 100 ms

Circuit Board

Voltage: 24V DC
Input Impedance: 3 kΩ
Current: 0–20 mA, 4–20 mA
Resolution: 12-bit
Isolation Voltage: 2 kV AC
Altitude: ≤ 2000 m

Analog Input Module

Function:16 AI: U, I, RTD, DI
Number of Analog Configurable I/Os:0
Analog Inputs:16
Input Signal:U, I, RTD, DI
Resolution:Analog Input 13 bit
Degree of Protection:Housing IP20
Supply Voltage:24 V DC
Ambient Air Temperature:
Operation 0 ... +60 °C
Storage -40 ... +70 °C

Robot spray accessory controller

Supply Voltage: 24V DC (±10%), 5A max.
Atomization air pressure control
Fluid flow regulation (via PWM or analog valve)
HV electrostatic control (up to 100 kV)
Solvent purge management
Diagnostic monitoring (clogs, pressure faults)
Power Consumption: 120W (peak)

Panel unit

Module Slots: 8 slots for S800 I/O modules
Orientation: Vertical
Bottom/top gland openings 
(M20/M25 cable glands)
Knockouts for field wiring

Binary In/Out Module

Input Impedance:  3-5 kΩ (High Range)
Maximum Continuous Voltage: 300V DC.
Maximum Surge Voltage: 1 kV, 1.2/50 µs waveform.
Operating Time: < 5 ms.
Release Time: < 5 ms.

Automatic voltage regulators

VOLTAGE REGULATOR
AUTOMATIC
COMPACT
SERIAL PORT
(UNITROL 1000)

I/O TERMINAL BOARD

System Power: 24 V DC
Field Power:24V DC
Data Transfer Rate: 
up to 12 Mbps for PROFIBUS DP

Binary Control Module

Range: Typically 20.4 V DC
Series: 83SR Safety Relay System
Channel-to-Backplane/Logic: Yes 
Isolation Voltage: Typically 250V AC
Safety Certification: TÜV Rheinland certified

MNS iS Motor Control Center

PROFIBUS DP (-V0) and PROFIBUS DP-V1
MODBUS RTU / TCP 
Power Supply 24V DC
Power Consumption Typical 1000mA

INVERTER TRIGGER DRIVER BOARD

Input Voltage: 24 V DC
Operating Temperature: -10°C to +70°C.
Storage Temperature: -25°C to +85°C.
Humidity: 5% to 95% non-condensing.

AC drive

Output Current: 105 A
Integrated Filter: L500 
Frame Size: R7
Cooling Method: Air cooling 
Voltage:3-phase 380–480 V AC (±10%)
Frequency:47–63 Hz
 Input Current:120 A
Motor Power Range:55–75 kW 
 Apparent Power (S1):89 kVA (at 480 V)

Pressductor PillowBlock Web Tensiometer

Measurement Range:0–50 kN 
Accuracy"±0.5% of full scale (typical)
Digital Option:RS-485 Modbus RTU 
Excitation Voltage:10–30 V DC
Bridge Resistance:350 Ω ±1%
Cable Length:Standard 10m
Overload Capacity:150% of rated range 

CONTROL DISTRIBUTION BOARD

Rated Operational Voltage (Ue) :230/400V AC (50/60 Hz)
Rated Insulation Voltage (Ui):500V AC
Rated Current (In):Up to 100A
Short-Circuit Capacity (Icn):10 kA 
Mounting Depth:10–120 mm
Material :Galvanized steel 

Main Circuit Interface Card

System Voltage:24 V DC (19.2–30 V DC)
Power Consumption:≤ 1.5 W (typical)
Communication Protocol:Profibus DP-V1
Modbus RTU (via FCI module)
Isolation:Galvanic isolation between 

HRC FUSE LINK

Fuselink
rated current 500A
size NH3
rated voltage 500VAC / 250VDC
utilization category gG
rated breaking capacity 120 kA (AC) / 80 (kA DC)

Binary Input Unit

Input Channels:16 
Input Type:Dry Contact or 24V DC Sourcing
Voltage Range:19–30 V DC
Input Current:3–5 mA per channel 
Logic Levels:"1" (ON): +15–30 V DC
"0" (OFF): 0–5 V DC
Response Time:≤ 2 ms (ON/OFF)
Overvoltage Protection:60 V DC (continuous), 75 V DC (1s)
Isolation:1500 V AC

UNITROL CARD

Input Voltage :24 V DC (±20%) 
or 48 V DC (±20%)
Analog Inputs:6 channels 
Digital Inputs:8 channels 
Analog Outputs:4 channels 
(0–20 mA / 4–20 mA)
Digital Outputs:6 channels
Processing Speed:32-bit DSP 
Communication:RS-485 Modbus RTU, CANopen

I/O Module Adaptor

Data Transfer Rate:Up to 12 Mbps (PROFIBUS)
Isolation Voltage:1.5 kV AC
Power Supply:24 V DC
Power Consumption:≤ 1.2 W

Binary I/O Module

Input Channels:16x Binary Inputs
Output Channels:10x Binary Outputs
Contact Rating (Outputs):5A @ 250V AC/30V DC
Input Voltage Ranges:24/48/110/125 V DC
Input Threshold (ON):>70% of rated voltage
Response Time:<10 ms 
Isolation Voltage:2.5 kV AC 
Power Consumption:≤ 5 W

Fiber Optic Remote I/O Termination Unit

Isolation Voltage:1.5 kV AC
Power Supply:24 V DC (±15%), 5 W typical
Redundancy:Dual fiber ports 
Fiber Interface:2x ST/PC connectors 
Data Rate:10 Mbps
Max. Distance:2 km 

Turbine Auto Sync Module

Input Voltages:100–120V AC
Voltage Diff: ±0.5%
Slip Freq: ±0.05 Hz
Operating Voltage:24/48/125V DC
Response Time:<20 ms

Turbine Protection Module

Operating Voltage:24/48/125V DC (±20%)
Response Time:<20 ms 
Speed Range:0–9999 RPM
Redundancy:2-out-of-3 (2oo3) voting logic
Overspeed Thresholds:2x Adjustable 
Input Signals:3x Magnetic Pickups (MPU) / Proximity Sensors
Trip Outputs:3x Relay Contacts (NO/NC, 5A @ 250V AC)

Analog Control Station

Operating Voltage:24V DC (±10%), 3W typical
Accuracy:±0.5% of full scale
Resolution:0.1% (for bargraph display)
Update Rate:100 ms
Isolation: 1.5 kV AC
MODE Switch: Toggle MAN/AUTO/CAS

Drive Unit Drive Controller

Control Platform:32-bit RISC processor with FPGA logic
Control Methods:DTC , Scalar, Vector
I/O Capacity:16x DI
Operating Voltage:24 V DC (±10%)
Power Consumption:25 W (typical)
Memory:2 GB Flash (firmware/logs)
    

Controller Module

Model: KUC755AE117 / 3BHB005243R0117
Product Type: Controller Module
Power Supply Voltage: 24V DC 
Operating Temperature: 0°C to +55°C
Storage Temperature: -20°C to +70°C
Humidity: Relative humidity 5% -95%

High voltage inverter board

Rated System Voltage:3300V AC (2.3–4.16 kV range)
DC Link Voltage:5600V DC (max)
IGCT Control :24x Gate driver channels 
Gate Drive Voltage:+20V / -5V
Auxiliary Power:24V DC (±10%), 150W
Isolation Voltage:6 kV AC 
Response Time:<2 µs 

MLink Control Unit

Model: M-Link (Motor Link)
Series: ABB MNS iS Intelligent MCC System
Processor:ARM Cortex-A9 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
MCC Bus Interface:MNS Connect
Operating Voltage: 110-240V AC (50/60 Hz)
Power Consumption:≤ 15 W

Drive Control Board

Control Methods:DTC 
Communication:Embedded
Operating Voltage:24 V DC (±10%)
Power Consumption:30 W (typical)
Memory:512 MB DDR3 RAM, 4 GB Flash

UNITROL 1010 Voltage Regulator

Generator Voltage:100–690V AC (50/60 Hz), 
Field Voltage (Output):10–250V DC
Regulation Accuracy:±0.5% 
Response Time:<30 ms 
Auxiliary Supply:24/48/110/250V 
Power Consumption:≤25 W (standby)

Handheld communicator

Mobility MFC Hand Held Configuration Device
Display:4.3" TFT LCD 
Touchscreen:Capacitive (glove-friendly)
Processor:ARM Cortex-A8 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
Charging:AC adapter (100–240V)
Operating System:Linux-based RTOS

Power Voting Unit

Input Channels:24V DC signals
Response Time:<10 ms
Operating Voltage:24V DC
Power Consumption:≤ 5 W
Isolation:1.5 kV AC

POWER SUPPLY BOARD

Acs880/580 Series Inverter
Input Voltage: 1-phase/3-phase input 
AC Input: 200–500 VAC
DC Input: 500–700 VDC
Frequency: 50/60 Hz
Output Power: ≤ 100 W
Output Voltage: Supplies +24 VDC
Load Capacity: 5 A @ 24 VDC

MC INTERFACE BOARD

Input Voltage: Typically 24V DC
Output Signals: Digital and analog signals for 
motor control and feedback.
Current Consumption:100-500mA 
Communication Voltage Levels: 3.3V or 
5V logic levels for digital communication.

Touch screen

Screen Size: 7 inches (diagonal).
Resolution: 800 x 480 pixels.
Display Type: TFT LCD with vibrant colors and excellent contrast.
Touch Screen Type: Resistive touch for accurate and reliable input.
Brightness: 400 cd/m².
Colors: 65,536 colors for sharp and detailed visualization.
Viewing Angle: ±70° )

Main Control Board

DCS880
SDCS-CON-H01
Main Control Board
Operating Voltage:24 V DC (±10%)
Current Consumption:≤1.5 A
Digital I/O Channels:32 optoisolated DC I/O points
Analog I/O:±10 V DC / 4–20 mA

ACS880 AC Drive- 500V, 3PH, wall mount, regenerative

LV AC industrial wall-mounted regenerative single drive
Input Supply:3-phase 380–480V AC (±10%), 50/60 Hz
Output Power:5.5 kW (7.5 HP) @ 400V AC
Output Current:21 A continuous (40°C ambient)
Overload Capacity:110% for 60s, 150% for 2s
Output Frequency:0–500 Hz (motor-dependent)
Efficiency:>98% (at full load)
Power Factor:0.98 (min)

Terminal base

Terminal base
For AC500 V3. 1 slot for communication module. 
2 Ethernet interfaces
1 serial interface
1 CAN interface (TB5610-2ETH)