ALL MANUFACTURERS

Turbine Protection Module

Operating Voltage:24/48/125V DC (±20%)
Response Time:<20 ms 
Speed Range:0–9999 RPM
Redundancy:2-out-of-3 (2oo3) voting logic
Overspeed Thresholds:2x Adjustable 
Input Signals:3x Magnetic Pickups (MPU) / Proximity Sensors
Trip Outputs:3x Relay Contacts (NO/NC, 5A @ 250V AC)

Analog Control Station

Operating Voltage:24V DC (±10%), 3W typical
Accuracy:±0.5% of full scale
Resolution:0.1% (for bargraph display)
Update Rate:100 ms
Isolation: 1.5 kV AC
MODE Switch: Toggle MAN/AUTO/CAS

Drive Unit Drive Controller

Control Platform:32-bit RISC processor with FPGA logic
Control Methods:DTC , Scalar, Vector
I/O Capacity:16x DI
Operating Voltage:24 V DC (±10%)
Power Consumption:25 W (typical)
Memory:2 GB Flash (firmware/logs)
    

Controller Module

Model: KUC755AE117 / 3BHB005243R0117
Product Type: Controller Module
Power Supply Voltage: 24V DC 
Operating Temperature: 0°C to +55°C
Storage Temperature: -20°C to +70°C
Humidity: Relative humidity 5% -95%

High voltage inverter board

Rated System Voltage:3300V AC (2.3–4.16 kV range)
DC Link Voltage:5600V DC (max)
IGCT Control :24x Gate driver channels 
Gate Drive Voltage:+20V / -5V
Auxiliary Power:24V DC (±10%), 150W
Isolation Voltage:6 kV AC 
Response Time:<2 µs 

Power Supply Module

Product Type : Power Supply Module
Model : SPW481 = 
100-120V AC Input Power Supply Module
Standard type with no explosion protection
With ISA Standard G3 and temperature (-20C - 70C)

Analog Input Module

Input Channels :16 Channels
A/D Converter Resolution:16 bits
Input Range:1 4-20 mA only (through 200 Ω)
Normal Mode Rejection Ratio, at 60 Hz:19 dB
Maximum Normal Mode Input: ± 30 Volts
Crosstalk, dc to 60 Hz (channel-to-channel):-60 dB
Input Scan Rate:50 ms

Analog Output Module

Power supply:24V DC
Rated Current:55mA at 24V
Power Consumption:1.32W at 20mA
Power/DCS to Field:1500 VAC
DCS side connections:
37 pin DSUB connector on CC-UGIA01
Voltage Input:24V DC
Interface to DCS:4 to 20mA with HART

MLink Control Unit

Model: M-Link (Motor Link)
Series: ABB MNS iS Intelligent MCC System
Processor:ARM Cortex-A9 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
MCC Bus Interface:MNS Connect
Operating Voltage: 110-240V AC (50/60 Hz)
Power Consumption:≤ 15 W

Drive Control Board

Control Methods:DTC 
Communication:Embedded
Operating Voltage:24 V DC (±10%)
Power Consumption:30 W (typical)
Memory:512 MB DDR3 RAM, 4 GB Flash

Current Input Module

Number of input channels 16 channels, module isolation
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C
Withstand voltage 1.5 kV AC between input signal and system for 1 minute

UNITROL 1010 Voltage Regulator

Generator Voltage:100–690V AC (50/60 Hz), 
Field Voltage (Output):10–250V DC
Regulation Accuracy:±0.5% 
Response Time:<30 ms 
Auxiliary Supply:24/48/110/250V 
Power Consumption:≤25 W (standby)

Handheld communicator

Mobility MFC Hand Held Configuration Device
Display:4.3" TFT LCD 
Touchscreen:Capacitive (glove-friendly)
Processor:ARM Cortex-A8 @ 800 MHz
Memory:512 MB RAM, 4 GB Flash
Charging:AC adapter (100–240V)
Operating System:Linux-based RTOS

Input Module

Number of inputs 16-channel, module isolation
Input current 6 mA ± 20 % 
Contact rating 24 V DC +20 % / -10 % 
External power supply 24 V DC +20 % / -10 % 
Input response time 40 ms maximum
Withstand voltage (*1) (*2) 2 kV AC 
between input signal and system for 1 minute
16-input line collectivelyconnected