
Power Distribution Module
Nominal AC Input Voltage 100 - 240 VAC
AC Input Voltage Range 85 to 264 VAC
DC Input Voltage Range 90 to 375 VDC
Frequency 43 to 67 Hz
Nominal Current 3.2 – 1.0 A
Efficiency > 90% typ. (24 W)
Inrush Current (max) Typ. < 30 A
Power Factor Correction Active power factor correction to better than 0.92
Voltage Phase Type Single phase (AC voltage)
PanelView Plus 6 700 Color Terminal Touch Screen
Operator Input:Touch
Lifecycle status:End of life
Resolution:640 x 480, 18-bit color graphics
Touch:Analog Resistive
Integrated ports:Ethernet, RS-232, 2 USB host
Input Voltage range:18-30VDC
Product Line:Panelview 6 Plus
Input Type:Touchscreen
Armoured Extension Cable
080 8.0 meters (26.2 feet)
01 Armored cable
05 CSA, ATEX, IECEx Approvals
3300 XL Standard Extension Cable
3300 XL Proximitor Sensor
3300 XL Proximitor Sensor
90 9.0 meters (29.5 feet)
system length,panel mount
Gap Voltage Output:-2 V to -18 V DC
Vibration Output:±5 V AC peak
Dynamic Range:0–10 kHz
Linearity:±1% over full scale
SLC 500 DeviceNet Scanner Module
Module Width:Single Slot
Compatible controllers:SLC 5/02 or later
Pass through:Supported
Communication Port:One (1) DeviceNet
Data Transfer speed:125Kbps
Storage Temperature:-40 to 85 C (-40 to 185 F)
Vibration: Tested 5 g @ 10-500Hz per IEC 68-2-6
Operating Shock:30 g peak acceleration, 11(+1)ms pulse width
Series:SLC 500
Digital Output Module
Extensive internal diagnostics to ensure data integrity
Optional redundancy
Electronic Overcurrent protection
Configurable Safe-state (FAILOPT)
Latched, pulsed or pulse-width
modulated output(per channel)
900H030102
DISCONTINUED BY MANUFACTURER
OUTPUT MODULE
DIGITAL
8-CHANNEL
120-240 V AC
50/60 HZ
REPLACED BY 900H03-0202
TKHAO081
DISCONTINUED BY MANUFACTURER
OUTPUT MODULE
ANALOG
8 CHANNEL
HART ENABLED
0-20 MA
10 VDC
TCIDA161
DISCONTINUED BY MANUFACTURER
HONEYWELL
TC-IDA161
INPUT MODULE AC DIGITAL 120VAC 50/60HZ 24VDC 13MA
900G030102
DISCONTINUED BY MANUFACTURER
INPUT MODULE
16 POINT
2.6 MA MAX/CHANNEL
120/240VAC
5 VDC
51304584100
DISCONTINUED BY MANUFACTURER
I/O MODULE
EPDGP BOARD
TDC 3000
FOR THE EPDG AND EPDG2 PERIPHERAL INTERFACE
900B010101
DISCONTINUED BY MANUFACTURER
OUTPUT MODULE
ANALOG
HC900
750OHM
0-60DEGREE C
21MA
5VDC
Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.