
























Card
                                                    
                                                    
                                                        
                                                        Type: Printed Circuit Board
Power Supply:24V DC
Operating Temperature Range:
0°C to 60°C
                                                    
                                                
Level and Pressure Measuring
                                                    
                                                    
                                                        
                                                        Process Temperature Range:
 -40°C to +150°C (-40°F to +302°F)
Process Pressure Range: 
-1 to +40 bar (-100 to +4000 kPa)
Output Signal: 4…20 mA/HART
Power Supply: 14…36 V DC
Protection Rating: IP66/IP68 (0.2 bar)
Wetted Materials: Stainless Steel (1.4435)
Probe Length: Up to 9,000 mm
                                                    
                                                
ADVANCED MICROCONTROLLER
                                                    
                                                    
                                                        
                                                        ADVANCED MICROCONTROLLER
18-36 VDC
ETHERNET CONNECTION
VGA CONNECTION
                                                    
                                                
POWER SUPPLY
                                                    
                                                    
                                                        
                                                        PHASES:3; PN(KW):0,648
UPRI(V):575(600)-500-460(480)- 400(415)-230(240)-200
USEC(V DC):24
ISEC(A DC):27/32,5 (60/40 CEL)
F(HZ):50...60
VECTOR GR./SHIELD WNG.:II0 /0
PROTECTION CL.:I; TA/ISOKL:60 /B
W(%):4,2; IP00
 TYPE OF TERMINALS:SCREW CONNECTION
INSTALLATION:SCREW; 
EN 61558-2-6, EN61131-2 >UL
CSA-RECOGNIZED
SAFETY ISOLATING TRANSFORMER
Drive Controller
                                                    
                                                    
                                                        
                                                        DC Bus Nominal Voltage:DC 300V
Nature of Firmware:Standard
Rated Current:12A
Multi interface, general purpose
                                                    
                                                
PROFINET fieldbus module
                                                    
                                                    
                                                        
                                                        Product or component type:Communication module
Product compatibility:Lexium 32M
Accessory / separate part destination:Servo drive
Number of addresses:256
Electrical connection:2 connectors RJ45
4 LEDs (green/red) for communication status
                                                    
                                                
Servo motor
                                                    
                                                    
                                                        
                                                        Range compatibility:PacDrive 3
Device short name:SH3.....P
Product or component type:Servo motor
Maximum mechanical speed:8000 rpm
rated supply voltage:115...480 V
Network number of phases:Three phase
Continuous stall torque:1.25 N.m at 115...480 V three phase
Continuous power:690 W
Maximum current Irms:5.7 A
Servo motor
                                                    
                                                    
                                                        
                                                        Maximum mechanical speed 8000 rpm
 rated supply voltage 115...480 V
Continuous stall current 2.9 A
Continuous power 1130 W
Speed feedback resolution 128 periods
Torque constant 0.7 N.m/A at 120 °C
Back emf constant 48 V/krpm at 20 °C
Maximum axial force Fa 80 N
                                                    
                                                
ACCELEROMETER
                                                    
                                                    
                                                        
                                                        Acceleration Range: ±2g, ±5g, ±10g, or ±50g
Voltage output, typically 0-5V or 0-10V
Supply Voltage:  5V DC or 12V DC
Operating Temperature: -40°C to +85°C
                                                    
                                                
Analog Input Module
                                                    
                                                    
                                                        
                                                        Universal Input Output IOTA
Input Channels 1 16 Channels 
Common Mode Voltage, dc to 60 Hz -6 to +5 V peak
A/D Converter Resolution 16 bits 
Normal Mode Rejection Ratio, at 60 Hz 19 dB
Normal Mode Filter Response Single-pole RC, -3 dB @ 6.5 Hz
Input Impedance (voltage inputs) > 10 M Ω powered
Input Scan Rate 50 ms 
                                                    
                                                
High-Speed Network Communication Modules
                                                    
                                                    
                                                        
                                                        Supports fiber-optic medium
NFPA Class B or Class A operation
Data is immune to all environmental noise
Optical isolation prevents ground loops
High-Speed NFN fiber-optic medium
Fiber type: 62.5/125 micrometers (multi-mode); 
50/125 micrometers (multimode), 
or 9/125 micrometers (single mode)
Maximum attenuation: 10 dB with 62.5/125 μm cable, 6
                                                    
                                                
CONTROL OPERATING UNIT
                                                    
                                                    
                                                        
                                                        SIMOVERT 
MASTERDRIVESVECTOR CONTROL
MOTION CONTROLOPERATING UNIT 
W. INTEGRATED MEMORY OP 1S
                                                    
                                                
CENTRAL PROCESSING UNIT
                                                    
                                                    
                                                        
                                                        Module Type:Central Processing Unit
Number of Slots:1 (Single slot)
Battery-backed memory: 1 Mbyte
Number of Points:12K discrete inputs and outputs 
Serial Ports:1 (RS422/485 compatible)
Current Required:3.3 Amps nominal
                                                    
                                                

 
	
		Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.