GE PACSystems RX3i

Power Supply Module

POWER SUPPLY MODULE
110/220 VAC OR 115 VDC
50/60 HZ
5 VDC OR +/-12 VDC OUTPUT
1.6/3.5/21 AMP OUTPUT
100 W MAXIMUM

CPU Processor Module

CPU PROCESSOR
1 GHZ
64 MEG OF MEMORY
2 SERIAL PORTS
OCCUPIES TWO SLOTS
REDUNDANT CPU
EXTERNAL HIGH CAPACITY BATTERY 
IC693ACC302 REQUIRED

Central Processing Unit

CONTROL MODULE
RX3I CPU
1 GHZ PROCESSOR
2 SERIAL PORTS
RS-485 / RS-232
20 MB USER MEMORY

RXi Controller

RXI CONTROLLER / PACSYSTEMS
HIGH PERFORMANCE DISTRIBUTED IO
PROGRAMMABLE
REQUIRES ICRXIACCIDM001A

RX3I PROFINET SCANNER MODULE

RX3I PROFINET SCANNER MODULE
10/100/1000 WITH FOUR PORTS
1.2AMP @ 3.3VDC
1.1AMP @ 5 VDC
SINGLE SLOT

small form-factor pluggable scanner module

Type:Scanner module
Speed:100 Mbps
Material:Multi-mode fiber (MMF)
Length:2 Kilometers
SD Card:Supported
Power:3.3 to 5 Volts
Port Connectors:Two RJ-45 and two SFP cages.
LED Indicators:Yes

Ethernet network interface unit

RX3I NIU WITH TWO SERIAL PORTS
20K OF LOCAL LOGIC
MODULE REQUIRES UNIVERSAL BASE (IC695CHSXXX)
REQUIRES ETHERNET MODULE (IC695ETM001)
NIU SUPPORTS ALL RX3I I/O MODULES

SCANNER MODULE

IC695PNS001
RX3I PROFINET SCANNER MODULE
10/100/1000 WITH FOUR PORTS
1.2AMP @ 3.3VDC
1.1AMP @ 5 VDC
SINGLE SLOT

PACSystems RX3i Universal Backplane

PACSystems RX3i Universal Backplane
(IC695 Series), occupies 1 slot
24 Vdc Nominal Operates 18Vdc to 30 Vdc
40 W Total, All Loads
14 AWG to 22 AWG, 1 wire per terminal
Power, P/S Fault, Overload, Overtemperature

Power Supply module

Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Outputs:3
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps

Analog input module

Series:PACSystem RX3i
Manufacturer:GE Intelligent Platform (GE IP); Emerson Automation (Current)
Part Number:IC694ALG221A
No of Channels:Four (4) input channels
Product Type:Input Module
Nominal Input signal:0-20 mA; 4-20 mA
Module Type:Analog
Channel update rate:2 ms
Product Description:Analog input module
Digital Resolution:12 bit
LED:1 Green "Module OK" LED
Common Mode Voltage:200 volts
Input Filter Response:325 Hz
Product Lifecycle Status:Active
Hot-Swapping:Not Supported
Accuracy:0.1 % full scale
Input filter response:325 Hz
Input impedance:250 ohms
Linearity:< 1 Least Significant Bit

CPU module

Series:RX3i PacSystem
Part Number:IC695CPE330-AFAT
Product Type:CPU module
Processor Clock Speed:1.0 Ghz
RAM:64 MB
NVRAM:64MB
I/O Points:up to 32 K I/O
Controller Redundancy:Supported
Maximum Program Blocks:512
Maximum Block Size:128 kilobytes

Abaco Systems RXI Box IPC

Dual Core COM Express CPU Module
Fanless Design
(2) Gigabit Ethernet Connectors
Operating Temperature Range of -25°C to +65°C

RX3i CPL410 Controller

Processor1.2 GHz AMD G Series Quad Core
Operating SystemVxWorks
Power requirements
Input Power (Max) - 20 Watts
Input Voltage (Min) - 18 VDC
Input Voltage (Max) - 30 VDC
DisplayOLED
SecuritySecure Boot and Trusted Platform Module (TPM)
MarineABS, DNV-GL, BV, LR

RX3i CPE400 Controller

Processor1.2 GHz AMD G Series Quad Core
Operating SystemVxWorks
Power requirements
Input Power (Max) - 20 Watts
Input Voltage (Min) - 18 VDC
Input Voltage (Max) - 30 VDC
DisplayOLED
SecuritySecure Boot and Trusted Platform Module (TPM)
MarineABS, DNV-GL, BV, LR

RX3i CPL410 Controller CPU

Processor1.2 GHz AMD G Series Quad Core
Operating SystemVxWorks
Power requirementsInput Power (Max) - 20 Watts, 
Input Voltage (Min) - 18 VDC
Input Voltage (Max) - 30 VDC
DisplayOLED
SecuritySecure Boot and Trusted Platform Module (TPM)
MarineABS, DNV-GL, BV, LR

RX3i CPL410 Controller CPU

Processor1.2 GHz AMD G Series Quad Core
Operating SystemVxWorks
Power requirementsInput Power (Max) - 20 Watts, 
Input Voltage (Min) - 18 VDC
Input Voltage (Max) - 30 VDC
DisplayOLED
SecuritySecure Boot and Trusted Platform Module (TPM)
MarineABS, DNV-GL, BV, LR

Central Processing Units

Series:PACSystem RX3i
Product Description Rackless: CPU
RAM:64 MB
Operating System:VxWorks
Flash Memory:64 MB
Operating system:VxWorks
No. of Program blocks:768 Program block
Input Power Requirement:20 Watts
Maximum Program block size 128 KB
Display:OLED
Local display:OLED display

INPUT MODULE

INPUT MODULE
32POINT
LOGIC
SERIES 90-30
POSITIVE/NEGATIVE
7 AMP MAX
24 VDC

POWER SUPPLY

IC694PWR321
POWER SUPPLY
120/240 VAC
125 VDC STANDARD

POWER SUPPLY

IC694PWR331
POWER SUPPLY
24 VDC
HIGH CAPACITY
FOR RX3I

OUTPUT MODULE

OUTPUT MODULE
12/24 VDC
POSITIVE LOGIC
32 POINTS
INTERFACE USES FUJITSU CONNECTOR

Relay Output module

Series:PACSystem RX3i
Part Number:IC694MDL930
No of Channels:Sixteen (16), individually isolated
Description:AC/DC Voltage Output Module
No. of channels:Eight (8), individually isolated
Operating Voltage:5 to 30 Volts DC or 5 to 250 Volts AC
Contact form:Normally Open (N.O.) Form A contacts
Output voltage range:5-250VAC / 5-30 VDC
Nominal output voltage:120-240 VAC; 24 VDC
Max. Backplane Draw:6.0 Milliamps
Minimum load:10 mA
Inrush Rating:5.0 Amps
Maximum inrush:5:00 AM
Relay contact life:150,000 -1,000,000 operations

Motion Controller Module

Series:RX3i PacSystem
Part Number:IC695PMM335
Catalog:IC695
No. of Axes:4
No of Master axes:1
Backplane Support:Universal Support
Motion Path Planning:1ms
Number of Slots:1 (single slot)
Position Loop Update Rate:500μs
Controlled Axes/Module:4
FSSB Velocity Loop Update Rate:125μs
Motion Path Planning:1 ms
FSSB Torque Loop Update Rate:62.5μs
Power Consumption at 5 V:0.45 A
Servo Command Interface:Fiber Optic
Power Consumption at 3.3 V:1.1 A
Floating Point:Yes

Analog input module

Manufacturer:Emerson Automation
Series:PACSystem RX3i
Product Description:Analog input module
Part Number:IC694ALG221
No of Channels:Four (4) input channels
Product Type:Input Module
Nominal Input signal:0-20 mA; 4-20 mA
Module Type:Analog
Channel update rate:2 ms
Number of inputs:4
Digital Resolution:12 bit
Input filter response:325 Hz
Input impedance:250 ohms
Input Filter Response:325 Hz
Common Mode Voltage:200 volts