Operating Temperature 0° to 50° C
Storage Temperature -20° to 80° C
Operating Humidity 5 to 95% (non-condensing)
Air Composition No corrosive gases permitted
Power Budget Requirements 5 VA @ 8--30 VDC
Fuse (external) 10 A time-lag (T)
Buffer for date/time Gold capacitor
Temperature class T4 (Zone 2)
Operating temperature 0 °C...+60 °C
Storage temperature -40 °C...+85 °C
Processor Atom E3815 1.46 GHz
Main 256 MB with ECC
Static RAM 2 MB with ECC
backed up by battery
1 GB on-boad flash memory
SDHC (4 to 32 GB) Class 10
D-sub 9 pins, male (*2)
Full/Half duplex (software settings)
Synchronisation Asynchronous
Operation 0° to 55°C
Transportation/storage 40° to 85°C (*1)
Dust 0.3 mg/m3 or less
Resistance to corrosive gases
ANSI/ISA S71.04 Class G2 (Standard)
(ANSI/ISA S71.04 Class G3, option)
Resistance to vibration
0.15 mm P-P (5 to 58 Hz), 1 G (58 to 150 Hz)
Resistance to shock
15 G, 11 ms
(during power-off, for sine half-waves in XYZ-directions)
Altitude 2000 m or less
High-performance
high-elibility modular controller
Memory with ECC
Low heat dissipation eliminates the need for a fan
Awealth of RAS features -CPU self-diagnostics
temperature monitoring. 1/0 diagnostics, and more
power supply module, local bus (SB bus)
and control network can all be duplexed
and all modules are hot-swappable
Can function as link active schedulers
(L ASs) for low-speed voltage mode (H1)
FOUNDATION Fieldbus segments
and link up FOUNDATION Fieldbus-enabled feld devices
Processor Atom E3815 1.46 GHz
Main 256 MB with ECC
Static RAM 2 MB with ECC
backed up by battery
1 GB on-boad flash memory
SDHC (4 to 32 GB) Class 10
D-sub 9 pins, male (*2)
Full/Half duplex (software settings)
Synchronisation Asynchronous
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
MC68030 at 25 MHz with MMU
MC68882 at 25 MHz
Data and Instruction, each 256 KByte
On-board via the FGA-002B
16 MByte DRAM with Byte Parity
4 MByte, 32-bit
An electronic converter used
in combination with the VITO probes
HART® communication to tank gauging ATG *2
ATEX KEMA 01ATEX1212
IECEx KEM 05.0014
Kosha certificate; 13-AV4BO-0487
FM I. D. 3015746
CSA certificate 1635480
Nominal Voltage 24 VDC
Type Control Module
Output Signals 32, commoned
Voltage Range 16-32 VDC
Maximum Voltage 36 VDC
Voltage Drop < 2.8 VDC @ 1.7A, typical
Power Module Load < 13 watts
MPC8240 32-bit microprocessor
L1 cache—16KB/16KB MPC60x class
32MB of on-board SDRAM
with optional ECCprotection
Two 32-pin PLCC/CLCC sockets for Flash memory;
upto 1MB capacity for on-board firmware
or userspecified requirements
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
operating 0 to 60°C ambient
storage -40 to 85°C
Humidity 5% to 95% non condensing
Altitude 10,000 ft (3,000 m)
Vibration 0.015 inch (0.38 mm)
Peak to Peak displacement with 2.5 g peak (max)
accelerationover 5 to 2000 Hz
Shock 0 g, 11 ms duration, half-sine shock pulse
Current +5V @ 0.30A
Architecture: 32-bit RISC
Clock Speed: Up to 1 GHz
Voltage 5V DC or 12V DC
Operating Temperature: 0°C to 60°C.
Storage Temperature: -20°C to 85°C.
Humidity: 10%–90% RH(non-condensing)
A16:D8
Four Full-Duplex Channels
Fully Programmable Synchronous
Asynchronous Operation
RS-232C, RS-423, RS-422A,
and RS-485 Compatible
0 to 1 Mbaud Data Rate
Self-Test Capability
Programmable Interrupt Capability
Modem Control Lines for Each Channel
Uses Four Industry-Standard 25-Pin Subminiature D Connectors
Double Eurocard Form Factor
Four Programmable Baud Rate Generators
(8) Sample-and-Hold
Analog Input Channels
12-Bit A/D Converter
PGA Provides Program-Controlled
Gains of x1, x2, x4, x8 and x16
125 kHz Maximum Scan Rate (Gain = x1)
Dual 128 KB Data Buffers for Analog Inputs / Outputs
Analog Function Generation
Voltage: 5V DC or 24V DC
Operating Temperature: -20°C to +70°C
Storage Temperature: -40°C to +85°C
Humidity: 10%–90% RH
Likely used in industrial control systems
Analog I/O channels
Voltage 24V DC or 5V DC
Operating Temperature: -20°C to 70°C
Storage Temperature: -40°C to 85°C
Humidity: 10–90% RH, non-condensing
8TP-1A865 #A6-4
HDMI, VGA, DVI, or composite
Voltage: Typically 12V DC or 24V DC
Operating Temperature: 0°C to 50°C
Humidity: 10–90% RH, non-condensing
Input Voltage Range 24 V DC
Operating Temperature -20°C to +60°C
Storage Temperature -40°C to +85°C
Input/Output Types Digital inputs (DI)
Operating Humidity 5% to 95% RH, non-condensing
Certification CE, UL, RoHS
High-speed processor
real-time data processing and control
Typically supports 16/32 digital inputs
Supports 4-20 mA or 0-10 V
-10°C to +55°C (14°F to 131°F)
20°C to +70°C (-4°F to 158°F)
10% to 90% non-condensing
High-speed microcontroller
embedded processor designed
for real-time control
5V or 24V
0°C to +50°C (32°F to 122°F)
-20°C to +70°C (-4°F to 158°F)
10% to 90%, non-condensing
ASKPCB
The board complies with UL 796 standards
Flame rating: V-0,
ensuring good fire resistance
Minimum conductor width: 0.28 mm
Maximum operational temperature: 130°C
Power Requirements 24 VDC
Operating Temperature Range -20°C to 60°C
Humidity Range 5% to 95%
Mounting Options
Standard DIN rail or custom rack mounting
Fully programmable customized menus
LCD color touchscreen, and buttons
Softkeys support different colors and text
Touch pad and touch ring
Ergonomic design with padded wrist rest
Variable-speed joystick with integral zoom control
L ocking power connector
Dedicated keys for commonly used functions
Dynamic menu selection
Web interface for configuration and firmware upgrades
Laser cut backlit keys
Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:
85 to 264 VAC or 100 to 300 VDC
Number of Slots:2
Output Power: 40 Watts max
Output Voltage:24 VDC, 5.1 VDC or 3.3 VDC
Output Current:0-1.6 A, 0-6 A, or 0-9 Amps
16 / 32 digital channels
16 channels can be configured as input or output
Configurable interrupt inputs
Status display for each channel via LED
Supply voltage 18 to 34 VDC
Supply voltage protected against reverse polarity
Cost effective and space saving
Head module for CANopen slave stations
Up to 30 I/O modules per slave station
Optional integrated power supply
Transfer rate 10 Kbaud to 1 Mbaud
Bus length to 5000 m (signal repeater required)
Two internally connected CAN interfaces for loop-through of the cable
Galvanic isolation between CAN interfaces and control electronics
Node address can be set via rotary switch
8 analog inputs
8 analog outputs
Connection possibility single-ended or differential
Power supply for up to 4 potentiometers
Temperature inputs for up to 4 Pt100/Pt1000 sensors
2-wire or 4-wire inputs for Pt100/Pt1000 sensors
Wire break detection for the inputs (for voltage and temperature)
Short circuit proof outputs
compact CAN slave module
16/32 channels can be freely configured as input or output
Digital outputs each with 1 A continuous current
Two internally connected CAN interfaces for loop-through of the cable
Galvanic isolation between CAN interfaces and control electronics
Baud rate and node ID can be set via rotary switch
Supply voltage 18 to 34 VDC
Operating range 0 to +60°C without additional cooling
Full wiring without additional backplanes
Up to 5000 mm (typically)
High, typically <1 μm
±0.05% FS (Full Scale)
Analog (0-10V, 4-20mA)
Digital (SSI, CANopen, Profibus, EtherCAT)
-40°C to +85°C
Number of input channels 16 channels,
module isolation (*5)
Rated input range 4 to 20 mA
Permissible input range 0 to 25 mA
Input impedance during Power-OFF 500 kΩ minimum
Data update frequency 40 ms
Temperature drift ±16 µA/10 °C
Withstand voltage 1.5 kV AC between input signal and system for 1 minute
16-channel, module isolation
6 mA ± 20 %
24 V DC +20 % / -10 % (*4), 10 mA or greater
24 V DC +20 % / -10 % (*3) (*4)Current capacity: 200 mA
30.0 V DC
40 ms maximum
2 kV AC between input signal and system for 1 minute, 16-input line collectivelyconnected
16-channel, module isolation
6 mA ± 20 %
24 V DC +20 % / -10 %
10 mA or greater
24 V DC +20 % / -10 %
Current capacity: 200 mA
30.0 V DC
40 ms maximum
2 kV AC between input signal and system for 1 minute
16-input line collectivelyconnected
16-channel, module isolation
24 V DC
1 V maximum
24 V DC, 3.4 A minimum
24 V DC + 20 % / -10 %
1.6 mA
0.2 A/output line (3.2 A in total output line) (*3) (*5)
120 to 685 Ω (*6
2 kV AC between output signal lines and system for 1 minute, 16-point input linescollectively connected (negative lines)
16-channel module isolation
6 mA ± 20 %
24 V DC +20 % / -10 %
Current capacity: 200 mA
24 V DC +20 % / -10 %
10 mA or greater
30.0 V DC
40 ms maximum
2 kV AC between input signal and system for 1 minute
16-input line collectivelyconnected
290 mA maximum (5 V DC)140 mA
maximum (24 V DC)
Voltage, Current, Thermocouple
Input Range:
Voltage: ±100mV to ±10V, Current: 4-20mA
Output Range:
Voltage: 0-10V, Current: 4-20mA
Accuracy: ±0.1% of full scale
Response Time: ≤ 250 ms
Power Supply: 24V DC
Isolation Voltage: 1500V AC
Operating Temperature: -10°C to +55°C
Voltage Current
Thermocouple
Voltage: ±100mV to ±10V, Current: 4-20mA
Output Range
Voltage: 0-10V, Current: 4-20mA
Accuracy: ±0.1% of full scale
Response Time: ≤ 250 ms
Power Supply: 24V DC
Isolation Voltage: 1500V AC
Operating Temperature: -10°C to +55°C
4 to 20 mA
16, isolated, standard switch-overresponse in redundant configuration
Between output and system: 1500 V AC, for 1 minute
0 to 750 Ω
Less than 0.65 mA
±48 µA
±16 µA/10 ˚C
230 mA (5 V DC), 540 mA (24 V DC)
Operating Voltage: 24V DC
Maximum Output Current: 0.5A to 1A
Response Time: Typically 1ms to 10ms
Operating Temperature: 0°C to 60°C
Storage Temperature: -20°C to 70°C
Threaded ports for conduit connections
A probe sleeve of optional lengthl O-rings
A reverse mount proximity probe
A thread seall Optional conduit fittings
An optional standoff adapter
2 pulse-width modulated output channels
2 shielded DSub connectors
for output channels
LED (green) per output
Choice of high-power or TTL output level
Monitoring of the load current
Monitoring of the external supply voltage
Monitoring of the internal temperature
2 input channels
for incremental and SSI encoders
Full 32 bit counter
2 analog outputs (14 bit)
4 fast digital input channels for initiator and trigger
Position measurement / position storage can be initiated via triggers
Virtual for use in applications:
zero pulse, speed, etc.
Synchronization via SYNC/PreSYNC
Resolution 14 bit (16 bitmeasured value averaging)
Averaging of measured values for interference suppression
Wire break detection the inputs
Channels isolated against the system
Monitoring of the external power supply
Cold junction temperature compensated
Control of up to (8) Axes
Point to Point Moves
(20) Digital Inputs
(12) Digital Outputs
(4) Differential Analog Inputs with 12-Bit Resolution
CANopen Protocol for Peer-to-Peer Communications with MintMT Controllers
