
Safety Builder R100.3 Software
Model Number:FS-SMSB-ST-100
Software Name:Safety Builder R100.3
Processor:Intel i7 2.8GHz or equivalent
RAM:16GB (32GB recommended)
Storage:500GB SSD
Basic Windows 2000/XP
Digital output module
Non-safe dry digital output FTA
8 channels, NO/NC
interconnection cable
eight non-safe potential-free
relaychangeover contacts
Digital output module
Non-safe dry digital output FTA
8 channels, NO/NC
interconnection cable
eight non-safe potential-free
relaychangeover contacts
Field termination assembly module
Non-safe isolated
24 V DC input channels
Field termination assembly module
sixteen non-safe isolated
Field termination assembly module
Non-safe isolated
24 V DC input channels
Field termination assembly module
sixteen non-safe isolated
Digital output module
Non-safe digital output module
24 V DC, 0.1 A
16 channels
100 mA non-safe output channels
drive loadsup to 2.5 W
Digital output module
Non-safe digital output module
24 V DC, 0.1 A
16 channels
100 mA non-safe output channels
drive loadsup to 2.5 W
Relay output module
Non-safe relay output module
contacts, 10 channels
Driveloads up to 70 W
ten potential-free relay contact
Relay output module
Non-safe relay output module
contacts, 10 channels
Driveloads up to 70 W
ten potential-free relay contact
Digital output module
Non-safe digital output module
24 V DC, 0.55 A, 12 channels
24 V DC, 550 mA output channels
Drive loadsup to 13 W
Digital output module
Non-safe digital output module
24 V DC, 0.55 A, 12 channels
24 V DC, 550 mA output channels
Drive loadsup to 13 W
Power Distribution Board
Power Distribution board
to power 2x FS-UCOM-HSE
2 pole header with keying
2 pole socket block
Single channel ethernet surge protector
NETWORK & COMMS PROTECTION
Single channel ethernet surge protector
protection against harmful voltages
MTL 24571 can be used
for shielded twisted pair (STP) cables
48V power on pins 1, 2, 3 and 6.
universal snap-in provisions
for standard DIN EN rails
Industrial Ethernet 5-port Switch
Purpose built DIN rail casing with integral clip
Port auto-negotiation and polarity detection
Transparent to industrial Ethernet protocols
Dual 10 – 57 VDC power input
Total galvanic isolation between each cable screen
IP 21
make Westermo
Low Voltage Digital Input Module
Input Voltage Range:5-30V DC
Threshold Levels:3.5V (ON), 1.5V (OFF) ±5%
Input Current 5mA @: 24V DC
Isolation:1500V AC
Response Time:<500μs
Channels:16
Input Type:Sink/Source
Filtering Programmable:0.1ms-100ms
Diagnostics:Per-channel LED indicators
COMMUNICATION INTERFACE MODULE
COMMUNICATION INTERFACE MODULE
500MA
5 VDC
1 X RS232 OUTPUT PORT
2 X RS485 OUTPUT PORT
Common mode filter
two female connectors
24V connectors
two male connectors
dual cable
a mounting bracket
DC power supply
25—28 V DC
Power supply
1200 W – UL508 approved
UL approved switched-mode
DC power supply
Under-voltage alarm (<22 V)
An output diode for parallel operation
Copyright Notice © 2004-2024 amikong.com All rights reserved
Disclaimer: We are not an authorized distributor or distributor of the product manufacturer of this website, The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because our company is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply.While many DCS PLC products will have firmware already installed, Our company makes no representation as to whether a DSC PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Our company also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from our company, its distributors, or any other source. Our company also makes no representations as to your right to install any such firmware on the product. Our company will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.