Siemens SINAMICS

AC Frequency Inverter

SINAMICS V20 
380-480 V 3 AC -15/+10% 
47-63Hz rated power 18.5 kW 
with 150% overload for 60 sec
small output overload: 22 kW with 110% 
overload for 60 sec. 
Integrated filter C3 I/O: 4 DI, 2 DO,2 AI, 1 AQ 
fieldbus: USS/MODBUS RTU 
with built-in BOP protection: IP20/ UL open 

Measuring Processor Module

MPM MEASURING PROCESSOR MODULE 
9 ANALOG INPUTS 
16 DIGITAL INPUTS 
TDM-BUS-INTERFACE 
RS232-INTERFACE

Power Module

SINAMICS G120 PM 240 Power Module 
unfiltered with integrated braking chopper 
380-480 V 3 AC +10/-10% 47-63 Hz 
power high overload: 0.55 kW at 200% 3 s
150% 57 s, 100% 240 s
ambient temperature -10 to +50 °C 
FSA degree of protection IP20 
without Control Unit and BOP

Controller Module

FUM 280
Power Supply:24V DC (19.2-28.8V)
Current Consumption:Typically 100mA (without load)
Power Dissipation:2.5W typical
Backplane Current:1.5A max

BLOWER FANASSEMBLY

SINAMICS/MICROMASTER PX REPLACEMENT FAN 
FOR 3AC 380-480 V
50/60 HZ, 260 A
AC DRIVE/POWER/MOTOR MODULES 
CHASSIS UNIT FRAMESIZE F

POWER SECTION BOARD

SIMOVERT MD 
PEU4 POWER SECTION BOARD
Compatible Drive Rating: 75kW
DC Link Voltage Range: 510V - 650V DC
Output Current: 165A
Switching Frequency:  2kHz - 8kHz 

ACTIVE LINE MODULE

ACTIVE LINE MODULE
SINAMIC S120
3 PHASE
INPUT 380-480 VAC
50/60 HZ
OUTPUT 16 KW
27 AMP
600 VDC
INT COOL

NORMALISING MODULE

NORMALISING MODULE
ABOFOR DEVICES
186 AMP
3 PHASE
380-460 VAC AND 510-620 VDC

BASIC LINE MODULE

SINAMICS S120 BASIC LINE MODULE
INPUT: 3 PHASE
380-480 VAC
50/60HZ
OUTPUT: DC 600 V
34 AMP
20 KW
FRAME SIZE: BOOKSIZE
INTERNAL AIR COOLING
INCL. DRIVE-CLIQ CABLE

CONTROL INTERFACE BOARD

CONTROL INTERFACE BOARD
SINAMICS S
FOR 3PH
380-480 VAC
50/60 HZ
380 A MOTOR MODULE

Control Module

Voltage: 24V DC (±15%)
Power Consumption: ≤10W
Isolation: 1500V AC
Analog Inputs:0-10V/4-20mA
Processor: 32-bit ARM
Memory:128MB Flash

SENSOR BOARD

SINAMICS S120 
SENSOR MODULE SMC10 
SENSOR BOARD FOR EVALUATION 
OF A RESOLVER 
WITHOUT DRIVE-CLIQ CABLE

Flat ribbon cable

flat ribbon cable 
BOP20 8-pole 
total length approx. 200 mm

Control Unit

SINAMICS S120 
Control Unit CU310 DP
with PROFIBUS interface 
without CompactFlash card

ACTIVE LINE MODULE

SINAMICS S120 ACTIVE LINE MODULE 
INPUT: 3AC 380-480V, 50/60HZ 
OUTPUT: DC 600V, 60A, 36KW 
FRAME SIZE: BOOKSIZE INTERNAL AIR COOLING 
INCL. DRIVE-CLIQ CABLE

THYRISTOR MODULE

Current Rating:1700A
Voltage Rating:1200V 
Gate Trigger Voltage:3V typical
Gate Trigger Current:200mA typical
On-State Voltage Drop:1.6V typical at rated current
Critical Rate of Rise:100A/μs
Isolation Voltage:2500V AC

BASIC OPERATOR PANEL

BASIC OPERATOR PANEL
SINAMICS G120
BOP-2
LCD
MONOCHROME
2-LINE DISPLAY
FOR USE WITH G120 INVERTERS
IP55

IGD3/R2 DRIVER BOARD

Control side (logic): +15V / -8V 
Auxiliary power: 24V DC
Peak gate current: Up to ±15A
Gate voltage range: +15V 
Switching Frequency: Up to 20 kHz
Isolation Voltage: ≥2500V RMS

Rectifier interfaces Module

Supply Voltage:24V DC ±10%
Power Consumption:15W (max)
Isolation:2500V AC 
Response Time:<100μs (fault signals)
Communication Rate:1Mbps (fiber-optic)
Temperature Monitoring:±1°C accuracy

Circuit Board

Supply Voltage:24V DC ±10%
Power Consumption:5W (max)
Isolation Voltage:1500V AC )
Communication Speed:Up to 12Mbps
PROFIBUS DP:9-pin D-sub

ACTIVE INTERFACE MODULE

SINAMICS S120 
ACTIVE INTERFACE MODULE 
FOR 55KW ACTIVE LINE MODULE 
INPUT: 3AC 380-480V, 50/60HZ

Smart Line Module

SINAMICS S120 
Smart Line Module 
500-690V 3AC, 50/60 Hz 
Output: 675-930 V DC, 1700A 
Rated power: 1400kW 
Built-in unit IP00 Internal 
air cooling incl. Drive-CLiQ cable

Smart Line Module

AC Input Voltage:3-phase, 380–480 V AC ±10%
Rated Input Current:41 A 
DC Link Output Voltage:510–720 V DC
Rated DC Link Power:30 kW
Peak Power:45 kW 
Efficiency:>98.5% 
Power Factor:≥0.99 

Inverter control Module

Inverter control Module 
IGD8 for devices 500-690V 3 AC
50/60 Hz and 675-930V DC
570A and 1080A

Parallel connection module

Parallel connection module 
For infeed units 3 AC 500-575V
50/60Hz und 660-690 V 3 AC
50/60 Hz

SMART LINE MODULE

SINAMICS S120 SMART LINE MODULE 
INPUT: 3AC 380-480V, 50/60HZ 
OUTPUT: 600VDC, 17A, 10KW 
FRAME SIZE: BOOKSIZE INTERNAL 
AIR COOLING 
INCL. CONTROL VOLTAGE 
ADAPTER MODULES PAINTED

Rectifier interfaces Module

Rectifier interfaces Module 
PER2 for infeed/regenerative 
feedback Supply units 
with Designs H and K 
380-480 V 3 AC, 50/60 Hz

Inverter control Module

Inverter control Module 
IGD7 for devices 500-690V 3 AC
50/60 Hz and 675-930V DC, 452A

Control Interface Board

MICROMASTER 440 PX 
replacement Control Interface Board 
for 380-480 V 3AC
50/60 Hz
310 A AC Drive

CONNECTOR BOARD

CONNECTOR BOARD 
PAINTED C98043-A7125-L100
Voltage Rating:≤ 60 V DC (signal level)
Current Capacity:2 A per bus line 

Power Interface Module

Power Interface incl. 
erminals C98043-A7106-L1
Electronic short-circuit protection (auto-reset)
Fuse monitoring (LED per channel)
Overvoltage clamp (40V max)
X1/X2: 24V DC Input (2x 4-pin terminal)
X10–X60: Output channels
X200/X201: Relay contacts

SINUMERIK 840D/DE CNC-HARDWARE

SINUMERIK 840D/DE CNC hardware
NCU 571.5B, 900 MHz 128 MB 
without system 
software memory: NC 3 MB, PLC 128 KB 
PROFIBUS DP prepared

Signal Conditioning Module

Normalizing module 
ABO For devices 
3 AC 380-460V 
and 510-620V DC
260 A

NTC thermistor

NTC thermistor 
for heat sink B57045-K682-K2 
with UL cable

Flat ribbon cable

Flat ribbon cable 
20-pole 900 A to 2000 A

SINAMICS BRAKING MODULE

SINAMICS BRAKING MODULE 
INPUT: 600 V DC 
OUTPUT: 250 KW/15 S 
FOR CHASSIS UNIT GX

Inverter Control module

Inverter Control module 
IGD4 for DEV 3 AC 380-460V, 
50/60 Hz and 510-620V DC, 370A

DCM DC converter

SINAMICS DCM 
DC converter for two-quadrant drives 
B6C connection 
Input: 400V 3AC, 50 A 
controllable: Field rectifier 
D485/60 MRE-GEE6S22 
Output: 485 V DC, 60A

Inverter snubber Module SML3

SIMOVERT MASTERDRIVES VC
600 V DC (nominal)
Typically up to 750 V DC
Peak Voltage Capability 900 V DC 

Inverter CU5 Control Board

Product:CU5 Control Board (Control Unit 5)
Article Number:6SA8252-0AC61
Series:SIMODRIVE 611
Function:Control and regulation of inverter modules
Application:Servo and spindle drive control
Communication Interfaces:- Serial interfaces (RS-232/RS-485)

CONTROL UNIT

SINAMICS CU320 
CONTROL UNIT 
WITHOUT COMPACT FLASH CARD 
WITHOUT UL APPROVAL

Inverter control Module

Inverter control Module 
IGD8 for devices 500-690V 3 AC
50/60 Hz and 675-930V DC
650 A and 1230 A

Flat ribbon cable

Flat ribbon cable 
20-pole 15 A and 30 A

Flat ribbon cable

Flat ribbon cable 
64-pole for device 
type 15 A to 600 A

SINAMICS SENSOR MODULE

SINAMICS 
SENSOR MODULE 
SME25 ABSOLUTE 
ENCODER: ENDAT 
PROTECTION IP67

Motor Control Module

TSE module
C98043-A7007-L1 

POWER INTERFACE COATED

Power Interface coated 
option L05 
C98043-A7107-L100

ACTIVE LINE MODULE

SINAMICS S120 
ACTIVE LINE MODULE 
INPUT: 3AC 380-480V, 50/60HZ 
OUTPUT: DC 600V, 92A, 55KW 
FRAME SIZE: BOOKSIZE INTERNAL 
AIR COOLING INCL. DRIVE-CLIQ CABLE

SINAMICS DRIVE CLiQ CABLE

SINAMICS DRIVE CLiQ CABLE 
IP20/IP20 Length: 2100mm

Inverter ABO Board

Normalizing module 
ABO For devices 3 AC 
660-690V and DC 890-930V
118A