Data rate: 10 Mbps
Max. distance: 100m (fiber length)
ModuleBus connection to AC 800M
Supply voltage: 24 VDC (±10%)
Power consumption: <5 W
Isolation: 1500 VAC
Supports up to 12 drives per module
Power Supply:24V DC (±10%)
Tachometer input: 0-10V DC or 4-20mA
Pulse input: Up to 100kHz frequency
Analog output: ±10V DC or 4-20mA
Relay outputs: 2x SPDT (5A @ 250V AC)
Speed Range: 0-10,000 RPM (configurable)
Resolution: 0.1% of full scale or better
Digital outputs: 24V DC, 0.5A
Voltage: 0-10V DC, ±10V DC
Current: 4-20mA, 0-20mA
Load Capacity:Voltage: ≥1kΩ
Isolation:1500V AC channel-to-channel
Backplane Power: 5V DC @ 500mA (typical)
Field Power: 24V DC (±10%) for outputs
Power Consumption: 6W (typical)
Voltage Rating: 1200V–1700V
Input Voltage (DC Link): 300–1000V DC
Output Voltage (AC): 3-phase, 0–480V AC
Current Rating: Up to 500A
Switching Frequency: 2–20 kHz
16 channels for 24 V d.c.
Redundant or single configuration
Output status indicators
Advanced on-board diagnostics
Degraded mode for normally energized channels
I/O Capacity:16 digital inputs (24V DC)
Processing Speed: 1ms scan time (typical)
Memory: 64KB SRAM
Power Supply:24V DC (±10%)
Consumption: 5W (typical)
Isolation:1500V AC (channel-to-channel)
0 – 25.4 mm/s (0 – 1.0 in/s)
10 Hz to 1 kHz (600 to 60 kcps)
RMS(Root Mean Square)
Multiple Approvals
(CSA/NRTL/C,ATEX/IECEx)
ExcitationVoltage12 to 30 Vdc
SettlingTimeLess than 15 seconds
within 2%of final value
MountedResonantFrequencyGreater than 12 kHz
TransverseSensitivity Less than 5% of sensitivity
SensingElementTypeCeramic / Shear
Input Voltage: 24V DC (±10%)
Power Consumption: 5W–10W (typical)
Isolation: 500V AC (channel-to-bus)
Processor: DSP or FPGA-based
Flash: 8MB–16MB
Digital I/O: 8–16 channels
DeviceNet or Profibus
RS-232/RS-485
A metal profile
Two plastic cover plates
A ground rail with 16 ground connection screws
Two power rails with M5 holes (+24 V and 0 V)
Eight mounting holes (6.35 mm diameter)
SIMATIC S7-1500 Digital input module
DI 16x24 V DC BA
16 channels in groupsof 16, input delay typ
3.2 ms, input type 3 (IEC 61131)
frontconnector Push-in
Operating Voltage: 24V DC (±10%)
Power Consumption: 15W typical
Signal Isolation: 2500V AC
Switching Frequency: Up to 20kHz
Gate Drive Outputs:±15V gate drive voltage
Power Requirements: 24 VDC, 9.5W
Voltage Range: 12–29 VDC (Note: No reverse polarity protection)
Fuse Rating: 2 A slow-blow (5 x 20 mm)
Maximum Switched Voltage: 300 VDC / 240 VAC
Maximum Switched Current: 0.5 A
Maximum Switched Power: 10 W
330704 3300 XL 11 mm Probe
M14 x 1.5 thread,with armor
Minimum length: 50 mm
10 1.0 meter (3.3 feet)
01Miniature coaxial ClickLocconnector
with connectorprotector, standard cable
05 Multiple Approvals
Input Voltage:24V DC (±10%) or 115/230V AC
Output Voltages:+5V, ±15V, +24V DC
Power Capacity:100W (max)
Inrush Current:15A (for 20ms at 230V AC)
Efficiency:>90% (at full load)
Fiber-Optic Signal Isolation :2500V AC
