ALL MANUFACTURERS

Output Module

Brand:GE Intelligent Platforms/GE Fanuc
Series:Series 90-70
Part Number:IC697MDL340
Product Type:Output Module
Rated Voltage:120 V AC
Outputs:16
DC Power:No
AC Power:Yes
LED Indicators:Yes

Universal analog input module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695ALG600
Module Type:Universal Analog
No of Channels:Eight (8)
Number of Inputs:8 general purpose
No. of groups:Two (2)
Cold Junction Compensation:2 channels
No. of channels per group:Four (4)
Power Dissapation:5.4W max
Humidity:5 to 95%, non-condensing
Module conversion method:Sigma-delta
Module resolution:11-16 Bits
Internal Power:3.3V: 350mA; 5V: 400 mA

printed circuit board

Input Voltage: 24V DC
Operating Temperature: Typically between -30°C to +65°C
Humidity: Typically 0-95% (non-condensing)

PACSystems RX3i Power Supply module

Part Number:IC695PSD140
Product Description:Power Supply module
Input voltage range:85 to 264 VAC 100 to 300 VDC
Power Supply:40 Watts
Nominal Rated Voltage:120/240 VAC or 125 VDC
Input Voltage Range:18 to 30 VDC
Input Power:60 Watts maximum at full load
Ripple:150 mV
Output Current:5.1 VDC
Noise:150 mV
Isolation:None
Number of Daisy-Chained PSD140:Up to 4
Terminal Current:6 Amps

NETWORK INTERFACE MODULE

Brand:GE Fanuc
Series:Versamax
Part Number:IC200BEM003
Description:VersaMax master module
Data:3854 input/output
Data Rate:9.6 k baud to 12 M baud
Connector:9 Pin D-sub
Bus Voltage:5 Volts
Slave Devices:125

RX3i 24VDC power supply, 40 watts.

▪+5.1 VDC output
▪ +24 VDC relay output that can be used to power circuitson Output Relay modules
▪ +3.3 VDC. This output is used internally by RX3i moduleswith IC695 catalog numbers 
▪Isolation NONE
▪Ripple (all outputs) 50 mV
▪Noise (all outputs) 50 mV 

I/O MODULE

Brand:GE Fanuc
Series:Genius I-O
Part number:IC660BRD020
Output circuits:16
Circuit type:Source
Weight:1.8 kilograms
Maximum ripple:10%

9905968
DISCONTINUED BY MANUFACTURER
LINKNET NODES AND I/O CONTROLLER MODULE
6-CH ANALOG INPUT
4-20 MA
WITHOUT 24 V LOOP

DS200GDPAG1AEB
DISCONTINUED BY MANUFACTURER
POWER SUPPLY BOARD
HIGH FREQUNCY
25 KHZ
MARK V

5501376
ANALOG MODULE

5466031
LINKNET CONTROLLER MODULE
4-CHANNEL
NETCON I/O

9905760
DISCONTINUED BY MANUFACTURER
LINKNET
TERMINATION RESISTOR MODULE

9905971
DISCONTINUED BY MANUFACTURER
INPUT MODULE
16 CHANNEL DISCRETE INPUT
24 VDC

Linknet 6-Channel Analog Input Module

Display Type: 2 line x 24 characters
Accuracy: 1 % at 25 °C
Power Supply Input: (18 to 32) V (dc)
Network to I/O channel: 277 V (ac)
Power supply input to network: 277 V (ac)
Power supply input to I/O channel: 500 V
Humidity Standards: 20 and 55 °C at 95% for 48hrs
Input Voltage: +24 Vdc at 1 A
Keypad/Display: 30 Multi-function Keypad
Temperature Range: (–40 to +55) °C

Output module

Brand:GE Fanuc
Series:RX3i PacSystem
Part Number:IC694MDL742
Type:Output module
Rated Voltage:12/24V DC
Isolation:250V AC continuous;
Electronic Short-Circuit Protection (ESCP):Yes
LEDs:Yes
Hot Insertion and Removal:Yes

5466409
DISCONTINUED BY MANUFACTURER
PC BOARD
MICRONET PENTIUM CPU
64 MB
233 MHZ

Discrete Output Module

Series:Versamax
Part Number:IC200MDL740
Number of Points:16 Outputs
Number of groups:1
Group to Group Isolation:None
Point to Point Isolation:None
Fuse:None

RX3i PACSystem option Module

Series:PACSystem RX3i
Manufacturer:Emerson Automation
Part Number:IC695CHS016
Product Description:Universal backplane
Grounding bar:Integrated
Module Hot-swap:Supported
Lifecycle status:Active
Mounting:Rack
No of slots:Sixteen (16)
Type:Universal backplane
Number of Slots:16
Input:+24 Volts
Recommended wire size:14 to 22 AWG
Enclosure:IP54 or greater

CPU MODULE

Series:RX3i PacSystem
Part Number:IC695CPE305
Clock Speed:1.1 GHz
RAM:5MB
NVRAM:10MB
Serial Communication:RS-232
Serial Ports:2
Communication standards:RS232; RS485
Ethernet Port:One (1)
Maximum Program Blocks:512
Number of Slots:1
Number of Local Racks:8
Program Storage:5 MB of User Memory
Type of Memory Storage:SRAM, Flash
Processor Speed:1.1G Hertz
Maximum Block Size:128 kilobytes

I/O pack

CARD
INPUT/OUTPUT PACK
PROTECTION TYPE
FOR MARK VIE TURBINE CONTROL SYSTEM
2 ETHERNET PORTS
POWER SUPPLY
LOCAL PROCESSOR
DATA ACQUISITION BOARD

9905970
DISCONTINUED BY MANUFACTURER
LINKNET MODULE
6-CHANNEL ANALOG INPUT
100 OHM RTD

Communications Module

UR7HH
DISCONTINUED BY MANUFACTURER
INTER-RELAY COMMUNICATIONS MODULE
HORIZONTAL UNIT
820 NM
MULTI MODE
LED
2 CHANNELS

Simplex Discrete I/O Module

5466258
DISCRETE I/O MODULE
SIMPLEX
48 INPUT
24 OUTPUT

55011432
CONTROLLER

NETWORK MODULE

NETWORK MODULE
PROFIBUS MASTER
SERIES 90-30
RS-232

Embedded Controller Module

Software: ControlST V04.03.18C
Relative humidity: 5% to 95%, no-condensing
Power Requirements +32 V dc to 18 V dc
Microprocessor: Freescale Power PC 
(Power QUICC II PRO 667 MHz)
Memory: 256 MB DDR SDRAM

I/O carrier barrier style

Brand:GE Fanuc
Series:Versamax
Part Number:IC200CHS001
Product Type:Barrier-style I/O carrier
Barrier-Style Terminals:36
Carrier Mounting:DIN rail
Max. I/O Points:32
Current per Point:Max 2 Amps

Analog input module

Manufacturer:GE Fanuc
Series:Versamax
Part Number:IC200ALG240
Product Type:Analog Input Module
Number of Inputs:8
Intelligent Module:Yes
Input Data:16-Bit Input Data
Operating Modes:Current Mode or Voltage Mode
Current Range:1 to 20 milliamps
Voltage Range:-10 to 10 Volts DC

INTERFACE MODULE

Brand:GE Fanuc
Series:Versamax
Part Number:IC200PBI001
I/O Modules:64
Network Address:1-125
User Diagnostics Data:5 bytes
Connector:9 Pin D-sub

CONTROLLER APPLICATION BOARD

531X139APMARM7
DISCONTINUED BY MANUFACTURER
PC APPLICATION BOARD

CPU MODULE

Manufacturer:GE Fanuc
Series:RX3i PACSystem
Part Number:IC698CRE030
Product Type:CPU
User Memory:64 MB
CPU:Redundancy CPU

Analog Output module

Series:RX3i PacSystem
Brand:GE Fanuc / Emerson Automation
Output Current Range:4 to 20 mA and 0 to 20 mA
Output Voltage Range:0 to 10V and -10 V to +10V
External Supply Voltage Range:20 VDC to 30 VDC
External Power Supply Voltage Ripple:10% (maximum)

Power Supply Module

Nominal rated voltage:120/240 VAC
Input Power:160 watts maximum at full load
Product Type:Power Supply Module
Load Capacity:100 Watts
No. of Outputs Three (3)
AC Input:90 to 264 VAC
Frequency:47 to 63 Hz
DC Input:100 to 150 VDC
Voltage regulation:5, 12, and -12 VDC

PROGRAMMABLE COPROCESSOR MODULE

Brand:GE Fanuc
Series:Series 90-70
Part Number:IC697PCM711
Power Supply:1.0 Amp
Connectors:3PL and 4PL
Slot Model:Single-slot Model
PC Programming:Supported

Ethernet Module

Series:Series 90-70
Product Type:Ethernet Interface
Restart Method:Pushbutton
Module Operating Voltage:+5 VDC, +12 VDC
+5 VDC, +12 VDC (from PLC power supply)
2.0 Amps (+5 VDC), typical
0.5 Amps (+12 VDC), 
maximum when powering an external AUItransceiver
0o C to +55oC (32oF to 131oF), ambient

Power Supply Module

Manufacturer:GE Fanuc
Series:RX3i PacSystems
Part Number:IC694PWR321
Product Type:Power Supply Module
Current Rating:2 Amps
Load-Sharing Redundancy:Not Supported

CPU Module

Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693CPU341P
Product Description:Modular CPU
Product type:CPU module
User memory:80 Kbytes
Processor type:80188
Processor speeds:20 MHz
Voltage input:5 Volts DC
Current draw:490 milliamps
Timers / Counters:> 2000
Serial port:1
Current load:490 mA

CPU Module

Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693CPU341N
Product Description:Modular CPU
Product type:CPU module
User memory:80 Kbytes
Processor type:80188
Processor speeds:20 MHz
Voltage input:5 Volts DC
Current draw:490 milliamps
Timers / Counters:> 2000
Serial port:1
Current load:490 mA

CPU Module

Series:Series 90-30
Manufacturer:GE Fanuc
Part Number:IC693CPU341J
Product Description:Modular CPU
Product type:CPU module
User memory:80 Kbytes
Processor type:80188
Processor speeds:20 MHz
Voltage input:5 Volts DC
Current draw:490 milliamps
Timers / Counters:> 2000
Serial port:1
Current load:490 mA