ALL MANUFACTURERS

DC Speed Control Power Supply Board

Input Voltage:110–230 V AC
Rated Power:Max ~10 W total load
DC Outputs:±15V (±1%) 
Control Loop:+24V DC (±5%) 
Max Current:+15V: 700 mA†
Voltage Ripple:50 mVpp (20 MHz BW)
Frequency Stability: 50/60 Hz (±3%)

CONTROL BOARD

CONTROL BOARD
CPU BOARD
Supply Voltage: 24 V DC (±15%)
Supply Voltage: 24 V DC (±15%)
Signal Inputs: 16 mA
Signal Outputs: 250 mA
Embedded Processor: 150 MHz

ELECTRONIC CONTROL BOARD

ELECTRONIC CONTROL BOARD
ADVANCED
DC SPEED
Control electronics 
Advanced painted 
incl. terminals 32 MB 
C98043-A7100-L204

Electronic module

INPUT MODULE
ET200L
32 POINT
DIGITAL
24 VDC

Digital Input Module

Type: Digital Input Module
Channels: 40 isolated input channels
Input Voltage: Nominal 24 VDC (range: 18–32 VDC)
Input Current: 6 mA per channel typical
Input Impedance: Approx. 4 kΩ
Logic Thresholds:
Logic '1': ≥15 V
Logic '0': ≤5 V

Trusted I/O and Communication Module

SHIELD FOR I/O AND 
COMMUNICATION MODULE 1SLOT
Trusted Shield Single Slot Width
Input Voltage:24V DC
Power Consumption: 8W 
Digital Inputs: 16–32 channels

Remote Expansion Cable

Full Trusted Controller Capability
100-240 Vac Input
Portable wheeled flight case
Simulation of 60 Field Signals
Pre-wired Dual Ethernet (point to point and hub)
Serial Comms wired to terminals
Configured for Companion Slot DI, AI and DO Modules

Trusted I/O SmartSlot Cable

Model Number: TC-501-02-6M5
Type: I/O SmartSlot Cable
Configuration: Typically used for internal connections
Channels: Supports 40 channels
Termination: Connects Trusted® I/O modules 
to FTAs or VFTAs

Power supply unit

Input Voltage Range:85–264 VAC or 120–370 VDC
Input Frequency:47–63 Hz
Output Voltage:24 VDC
Output Current:Up to 16 A
Efficiency:94–95 % at full load
Protection Class:IP20
Operating Temperature:–25 °C to +55 °C

DIGITAL INPUT MODULE

DIGITAL INPUT MODULE
SIMATIC S5
115V AC/DC
16 INPUTS
ISOLATED FOR S5-115U

3200 P2 genset control model

Part Number:EasyGen 3200-1
Discrete Input Range:12/24 Vdc
Power Consumption：< .15 W
Power Supply：12/24 Vdc
Operation Temperature:-30 to 80 °C
Storage Temperature:-20 to 70 °C
Humidity:95%, non-condensing
 P/n : 8440-2051

Safety dc discrete input module

Discrete input number:16
Group of channels:1
Logic input:Positive (sink)
Discrete input voltage:24 V DC
Voltage state 1 guaranteed:11...30 V DC
Voltage state 0 guaranteed:-3...5 V DC
Current state 1 guaranteed:>= 3 mA
Current state 0 guaranteed:<= 1.5 mA
Sensor power supply:19.2…30 V
Addressing requirement:7 input words
Input impedance:3675 Ohm
Absolute maximum input:30 V

CompactFlash card

SINAMICS S120 
CompactFlash card 
without performance expansion 
V4.8

POWER CONTROLLER MODULE

SIMOVERT 
POWER CONTROLLER MODULE
F/UNITS
72 AMP
510-620V DC

POWER OUTPUT MODULE

MASTER DRIVE
SIMOVERT
POWER OUTPUT MODULE
PEU FOR DEVICES
34 AMP
3 PHASE
380-460 VAC

IGBT module

Collector-Emitter Voltage：1200 V
Continuous Collector Current：450 A
Configuration: Half-bridge module
Package Type: EconoDUAL™ 3
Switching Technology: Trench/Fieldstop IGBT4

TECHNOLOGY BOARD

TECHNOLOGY BOARD
T300
WITHOUT LBA AND MEMORY MODULE
SIMOVERT MASTERDRIVES

Driver board

BOARD
IGD2/R4
480 V / 650 VDC
310 AMP
SINAMICS S120
MULT-AXIS

POWER SUPPLY MODULE

POWER SUPPLY
SITOP PSU8200
STABALIZED
3 PHASE
INPUT: 400-500 VAC
50/60 HZ
OUTPUT: 10 AMP
48 VDC
-25 TO +70 DEGREES C

Power output module

SIMOVERT Masterdrives 
Power output module 
PEU For devices 47 A 
510-620 V DC

Power output module

SIMOVERT MASTERDRIVES
MODULE
380-480VAC
50/60HZ
79.2 AMP
37 KWATT
3 PHASE

Control board

Component Type:CUCP 
Power Supply:24 VDC
Operating Voltage:24 VDC
Operating Temperature:0°C to +50°C
Storage Temperature:–25°C to +70°C

Control Interface Board

MICROMASTER 440 
PX replacement Control Interface Board 
for 380-480 V 3AC
50/60 Hz
380 A AC Drive

CONTROL INTERFACE BOARD

SINAMICS S 
CONTROL INTERFACE BOARD 
FOR 3PH 380-480 V
50/60 HZ, 210 A 
MOTOR MODULE

Control Interface Board

SINAMICS S 
Control Interface Board 
for 500-690V 3AC
50/60 Hz, 1270A 
Motor Module