ABB Advant OCS and Advant-800xA

ABB Standard Panel 15

Panels 800
2.1-inch TFT/LED display
Interaction type: Resistive touch
Display resolution, ratio: 1280 x 800 pixels

CONTROL BOARD

UDD406A 
3BHE041464R0101
CONTROL BOARD
Network Interface Module

DRIVE CONTROL BOARD

PCD237A101 
PEC80-CCM
3BHE028915R0101 
DRIVE CONTROL BOARD

CPU Board

YPQ201A
CPU Board 
CONTROL BOARD
YT204001-KA

BRIDGE ADAPTIONS BOARD

SDCS-BAB-F02 
3ADT316400R0502
Power Supply:24 V DC
BRIDGE ADAPTIONS BOARD 

MC INTERFACE BOARD

DD C779 D102 
PEC80 Converter Signal Int
MC INTERFACE BOARD
RETRO- PINT (ACS)

Control Board

3BHB000272R0101 
UFC719 AE101
Multiple I/O
Control Board

System 800xA Controller

STAINLESS STEEL VALVES
H-900-HP-SS-L-1/4-C870PCE
Enhanced controller reliability
Improved performance
Simultaneous support for all connected I/O subsystems
Downloadable firmware
100 Mbps Ethernet port 
for IEC61850 protocol communication on control level
Serial interface for Modbus RTU 
protocol communication on control level
Two redundant PROFIBUS DP lines

High Performance I/O DSP Board

High Performance I/O DSP Board Type 
PS861E 
1JNL100114‐077

Voltage Transducer Control Board

3BHE014185R0001 
UUD148 AE01 
Voltage Transducer Control Board
Input Voltage Range:0 – 5 A AC/DC
Supply Voltage:24 V DC
Power Consumption:≤ 5 W

ACS880 CONTROL PANEL

ACS-AP-I
3AUA0000088311 
ACS880 CONTROL PANEL

Analog Input Module

8 differential input channels for thermocouple/mV.
Channel 8 can be designated as
the CJ-channel (4-wire Pt100 RTD)
Variety of thermocouples with the following characteristics: 
B, C, E, J, K, N, R, S and T for AI835A also D, L and U
15 Bit resolution (A/D)
Inputs are monitored for wire-break open-circuit

AC 800M Controllers

ISA Secure certified - Read more
Reliability and simple fault diagnosis procedures
Modularity, allowing for step-by-step expansion
IP20 Class protection without the requirement for enclosures
The controller can be configured with 800xA control builder
The controller has full EMC certification
Sectioned CEX-Bus using a pair of BC810 / BC820
Hardware based on standards for optimum communication connectivity
(Ethernet, PROFIBUS DP, etc.)
Built-in redundant Ethernet Communication ports

AC 800M Controllers

ISA Secure certified - Read more
AC 800M High up to SIL 3 certified using PM857/SM812,PM863/SM812
PM865/SM811 or PM867/SM812
Supports S800 I/O High Integrity 
(PM857, PM863, PM865, PM866A and PM891)
The controller can be configured with 800xA control builder
The controller has full EMC certification
TÜV Certified SIL 2 and SIL 3
Built-in redundant Ethernet Communication ports

Safety CPU module

Use with PM857, PM863 and PM867
Package including
SM812, Safety Module
TP868, Baseplate
TK852V10, Syncronization link cable

Drive Control Unit

DCC2324B
3EST000214-2059  
Drive Control Unit
Supply Voltage:24 V DC
Power Consumption:60 W
Isolation:Reinforced 1.5 kV between logic and traction power

Digital input submodule

Rated Voltage:24 V DC (18 … 30 V)
Input Current:4 mA @ 24 V  
Thresholds:ON ≥ 15 V, OFF ≤ 5 V, 2 V hysteresis
Minimum Pulse:200 µs 
Isolation:500 V AC channel-to-back-plan 

FEEDER PROTECTION AND CONTROL

Three-phase non-directional overcurrent protection
Double earth-fault protection 
Non-directional earth-fault
Non-directional sensitive earth-fault
Directional earth-fault protection
Transient/intermittent earth-fault protection
Negative-phase-sequence protection
Phase discontinuity
Three-phase transformer inrush detector
Three-phase thermal overload, lines and cables
Circuit breaker failure protection
Electrically latched lockout relay

Power Supply

NSD570
1KHW002144R0001
Additional items NSD570
G3LK, Power Supply 110-250 VDC/VAC NSD570

Analog Signal Multiplier

Power Supply:24V DC (±10%)
Power Consumption:3.5W
Input Signals:2× (0-10V or 4-20mA)
Output Signal:0-10V or 4-20mA 
Input Impedance:1MΩ (voltage), 250Ω (current)
Isolation:1500V AC 
    

Splitter Board

Input Voltage:24V DC (±10%)
Power Consumption:2W max
Isolation Voltage:1500V AC
Input Channels:4 (configurable)
Output Channels:8 (1:2 splitting ratio)
Signal Types:4-20mA, 0-10V, digital

Exciter Control Module

Power Supply:110/220V AC ±10% or 24/48V DC
Power Consumption:50W (max)
Field Voltage :0-300V DC (adjustable)
Field Current:0-20A DC (continuous)
Control Accuracy:±0.25% of setpoint
Response Time:<10ms
Voltage Regulation:±0.5% of nominal
Frequency Range:40-70 Hz
Stability:<0.1% oscillation
Harmonic Distortion:<1% THD

Analog I/O Module

ANALOG I/O
MODULE 8AI
24 VDC
U/I/RTD
8/12BIT+SIGN 1/3-WIRE
CS31

OEI-BOARD

Power Supply:24V DC (-15%/+20%)
Power Consumption:6W typical
Optical Interfaces:2× 100BASE-FX (1300nm)
Electrical Interface:1× 10/100BASE-TX
Isolation:1500V AC
Data Rate:100Mbps full-duplex

REV H DIODE SUPPLY CONNECTOR BOARD

Input Voltage: 24V DC
Output Voltage: ±15V DC
Current Rating: ≤ 2A per
Isolation Voltage: ≥ 2500V AC
Input: 6–10-pin terminal